Posts made by the_gibson

@crpalmer @Dougal1957 @T3P3Tony

Turned out to be a Z-offset in my slicer I dismissed because I needed it before.

All is working as it should now.

Thank you for your help, and the debugging assist!

@the_gibson

ok, I'm dumb... z-offset in the slicer was the culprit.

now mostly printing... have some tuning to do... but working.

@crpalmer said in Tevo LM recent conversion and z step issues:

M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E403.00 ; set steps per mm'

Adjusted back to these settings.

printing one now... this is going to be funny.

@crpalmer I have reduce the extruder steps all the way down to 160... still happening...

Starting to rule out overextrusion.

adding current config.g

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.4 on Sun Oct 10 2021 10:43:02 GMT-0400 (Eastern Daylight Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"HOWEE"                                      ; set printer name
M555 P2
M665 R157 L397.107 B175 H525                        ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0.15 Y0.08 Z0.07                                      ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 S1                                            ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S1                                         ; physical drive 0 goes forwards
M569 P1 S1                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X32 Y32 Z32 E32 I1                            ; configure microstepping with interpolation
M92 X160 Y160 Z160 E810							; set steps per mm
M566 X1500.00 Y1500.00 Z1500.00 E1500.00           ; set maximum instantaneous speed changes (mm/min)
M203 X39960 Y39960 Z39960 E3000.00        ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1500.00           ; set accelerations (mm/s^2)
M906 X1100 Y1100 Z1100 E880 I30                   ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 Z0 S1                                         ; set minimum Z

; Endstops
M574 X2 Y2 Z2 S1                                   ; set active high endstops

; Z-Probe
M307 H3 A-1 C-1 D-1                                ; disable heater on PWM channel for BLTouch
M558 P9 H5 F120 T6000                              ; set Z probe type to bltouch and the dive height + speeds
M558 H30                                           ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
G31 P500 X0 Y20 Z4.4                                 ; set Z probe trigger value, offset and trigger height
M557 R150 S45                                      ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 0
M143 H0 S100                                       ; set temperature limit for heater 0 to 100C
M305 P1 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 1
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1                             ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                          ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

@crpalmer I am leaning toward overextrusion now as well.

@dougal1957 Definitely 20's.

@dougal1957 I have not. Assumed they were what was listed on the printer specs. You think they are 16's?

@dougal1957 Stock 20 tooth pulleys.

@t3p3tony like the Z steps aren't moving appropriately. As soon as the second layer starts, you can hear the hotend dragging across the print, eventually either breaking the extruded material free of the bed, or creating a very deformed print. This still feels like either an extrusion issue, or a z steps being off issue.

but first problem is definitely fixed.

@the_gibson It is better, but definitely still dragging the print. first layer goes down great.

@the_gibson ok, looking good now.

G32
Calibrated 6 factors using 13 points, deviation before 0.036 after 0.035

Going to try another print.

@dougal1957 Already all over that... and yes, carriage is good now.

I'll be posting back with results shortly.

definitely getting better.

G32
Calibrated 6 factors using 13 points, deviation before 0.085 after 0.031

@the_gibson

How about that...

G32
Calibrated 6 factors using 13 points, deviation before 1.177 after 0.026

@dougal1957 said in Tevo LM recent conversion and z step issues:

G30 P3 X0 Y-140 H0 Z-99999

Testing now!

@t3p3tony High deviance no matter how many times I run it... I think I found why, and now I'm working on figuring it out. When the furthestmost forward Probe point is attempted, the sled for the X Axis is hitting the end of it's bottom travel, and bumping twice before it triggers the probe. That reading has to be throwing the whole thing off.

Going to work on adjusting the height of the bottom pulley, but is there a way to adjust the probing pattern? This is odd, because no mechanical changes were made, and the old smoothie board worked fine in this way.

@crpalmer Latest returns:

M665
Diagonals 397.190:397.190:397.190, delta radius 159.764, homed height 528.280, bed radius 155.0, X 2.836°, Y 1.408°, Z 0.000°

M666
Endstop adjustments X-0.53 Y-0.74 Z1.27, tilt X0.00% Y0.00%

@the_gibson I am however, pretty far from stock myself, just not on the motors. BMG, Mosquito, all the typical noise mods.

@crpalmer You may be right, but it worked fine with this deviation (I am assuming since the geometry didn't change) on the old setup.

I'll tune it further.

@crpalmer Conversely, do you have a known good config I could compare it to?

@crpalmer
Calibrated 6 factors using 13 points, deviation before 4.965 after 0.453

I am, because when I remove that I get an error about the Z probe not triggering when it plainly does. willing to address that one AFTER I print the board mounts.