@deckingman Yes, it is RepRap. I disconnected the Paneldue and was able to do a 2.5 hour print with no issues and no Bad commands appearing in the logs.
I will be changing the PanelDue cable to a shielded one later today (after work) and trying again.
@T3P3Tony I don't believe it is an SD card issue, or file corruption issue as I tried with a new card and new file. I also verified the files are proper when compared to eachother.
@deckingman this has all my config files and a copy of the G-code.
https://www.dropbox.com/sh/yvealx81yym4kqh/AACMONG_FHO9DB7TqGrw7dyia?dl=0
Also, Note. I tried using different slicers, and got the error in all of them.
Feel free to take a look and let me know if you can see what's happening.
It was a fresh g-code. I also tried a different print and it ended up giving the same Attempting to extrude error.
I changed out the SD card with a new out of the box class 10 one. This was my output of the eventlog. The print did complete.
2020-09-27 00:25:13 Event logging started
2020-09-27 00:25:35 Error: Bad command: J184 M409 F"d99f"*71
2020-09-27 00:26:15 Error: M409: control character in string
2020-09-27 00:26:56 Warning: the height map was loaded when the current Z=0 datum was not determined probing. This may result in a height offset.
2020-09-27 00:31:03 Error: M409: control character in string
2020-09-27 00:36:36 Error: Bad command: s73 M409 F"d99f"
2020-09-27 00:36:37 Error: Bad command: `M409 F"d99f"
2020-09-27 00:36:38 Error: Bad command: >0M409 F"d99f"+72
2020-09-27 00:36:56 Warning: M609: Command is not supported
2020-09-27 00:37:00 Error: Bad command: M<09 F"d99f"
2020-09-27 00:37:06 Error: Bad command: ^403 M409 F"d99f"*77
2020-09-27 00:37:11 Error: M409: control character in string
2020-09-27 00:37:55 Error: M409: expected string expression
2020-09-27 00:38:19 Warning: M40: Command is not supported
2020-09-27 00:38:26 Warning: M429: Command is not supported
2020-09-27 00:41:23 Error: M409: control character in string
2020-09-27 00:41:47 Error: M409: control character in string
2020-09-27 00:41:55 Warning: M429: Command is not supported
2020-09-27 00:45:03 Error: Bad command: $M409 F"d99f"
2020-09-27 00:48:07 Error: Bad command: O409 F"d99f"
2020-09-27 00:48:23 Error: Bad command: O628 M409 F"d99f"*70
2020-09-27 00:49:36 Error: Bad command: `m409 F"d99f#*78
2020-09-27 00:51:28 Error: Bad command: < M409 F"d99f"
2020-09-27 00:53:12 Error: M409: control character in string
2020-09-27 00:53:52 Warning: M40: Command is not supported
2020-09-27 00:54:20 Error: Bad command: ?17 M409 F"d99f"
2020-09-27 00:54:48 Error: M4: Command is not supported in machine mode FFF
2020-09-27 00:55:40 Error: Bad command: `M409 F"d99f"
2020-09-27 00:57:00 Error: Bad command: `M409 F"d99f"
2020-09-27 00:58:32 Warning: M40: Command is not supported
2020-09-27 01:00:28 Error: M4: Command is not supported in machine mode FFF
2020-09-27 01:02:05 Error: M409: expected string expression
2020-09-27 01:02:53 Warning: M40: Command is not supported
2020-09-27 01:05:57 Error: Bad command: :91 M409 F"d99f"
2020-09-27 01:11:05 Error: M409: expected string expression
2020-09-27 01:12:05 Error: Bad command: 3 M409 K"job" F"v"
2020-09-27 01:14:26 Error: Bad command: 018 M409 F"d99f"
2020-09-27 01:15:22 Error: M409: expected string expression
2020-09-27 01:15:34 Error: M409: expected string expression
2020-09-27 01:17:58 Error: M4: Command is not supported in machine mode FFF
2020-09-27 01:18:34 Error: Bad command: (M409 K"job" F"v"
2020-09-27 01:20:38 Error: M409: expected string expression
2020-09-27 01:24:42 Error: Bad command: J1172 M409 F"d99f"*127
2020-09-27 01:26:48 Warning: M509: Command is not supported
2020-09-27 01:28:26 Error: Bad command: y M409 F"d99f"
2020-09-27 01:30:55 Error: M4: Command is not supported in machine mode FFF
2020-09-27 01:31:11 Error: Bad command: :0 M409 K"job" F"v"
2020-09-27 01:34:27 Warning: M40: Command is not supported
2020-09-27 01:36:11 Error: Bad command: 55 M409 F"d99f"
2020-09-27 01:37:53 Finished printing file 0:/gcodes/Printer Parts/Flying_Bondtech.gcode, print time was 1h 14m
ok, Nevermind... happened again. Here is the Diagnostic logs.
@dc42 I tested the resistance, and it is below 0.1. Also the wires are not near any stepper motors.
m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L2MS8-6JTDD-3S06N-98HLP
Used output buffers: 3 of 24 (24 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93556 of which 92 recycled
Exception stack ram used: 528
Never used ram: 8916
Tasks: NETWORK(ready,308) HEAT(blocked,1224) MAIN(running,1788) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 00:43:59 ago, cause: software
Last software reset at 2020-09-26 21:20, reason: User, spinning module GCodes, available RAM 9316 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 4
MCU temperature: min 33.0, current 35.7, max 36.1
Supply voltage: min 24.4, current 24.6, max 24.8, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/205
Driver 1: ok, SG min/max 0/211
Driver 2: ok, SG min/max 0/201
Driver 3: standstill, SG min/max 0/193
Driver 4: standstill, SG min/max not available
Date/time: 2020-09-26 22:04:29
Cache data hit count 4029131711
Slowest loop: 59.57ms; fastest: 0.14ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 8
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 5.1ms, write time 28.9ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 166, MinFreeDm: 101, MaxWait: 703770ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 29343, completed moves: 29335, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: 3
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.3
=== GCodes ===
Segments left: 2
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 2
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 63.59ms; fastest: 0.00ms
Responder states: HTTP(4) HTTP(2) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address dc:4f:22:6e:60:44
WiFi Vcc 3.34, reset reason Unknown
WiFi flash size 4194304, free heap 24568
WiFi IP address 192.168.1.253
WiFi signal strength -51dBm, reconnections 0, sleep mode modem
Socket states: 2 2 0 0 0 0 0 0
=== Filament sensors ===
Extruder 0 sensor: ok
I am still not sure what's happening here. Can someone please assist!?!?!?
Here is a download of all the Duet Config files.
https://www.dropbox.com/s/9okmtuly2bz2gmk/Duet Configs.zip?dl=0
ok, so I have now done 2 prints without this error happening.
Here was my fix.
I have no idea why, but this worked so far. I'm going to keep this open until i get a good 10 prints with no more of this error.
Update: ran a test print, same issue.
I am now downgrading versions of the duet firmware to 3.0 to see if that resolves it.
Sorry to bring up an old thread, I am having the exact same issue. Has there been any updates to this?
I have removed that line. I'll run another test print to verify.
PID's now tuned, I'll try the print again.
I'm using only the standard 4 pin cable, I believe it's 1 meter long. The cable path is not near a stepper motor, about 6-in away from the nearest motor.
I ran a simulation, no errors.
I looked at a file from the DWC, and it does not seem that any of the commands are corrupted.
no faults, no tool change commands.
One thing I just noticed, the PanelDue 7i displays at random during a print, a bunch of random errors, like "Error: Bad command R12*27"
These errors do not show up in any console.
@Phaedrux
Thanks for the reply!
No heater errors. I have not PID Tuned, however the temp graph is stable, basically almost a straight line. The issue is that the extruder stops extruding until I send a T0.
I manually edited that gcode to add a T0 to each layer and it printed, however this is not a fix.
*bump
I re-did the config.g as below, and am still getting this issue.
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Fri Sep 18 2020 09:00:56 GMT-0500 (Central Daylight Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"twhpredator" ; set printer name
; Delta Settings
M665 R185 L440.49 B175 H405 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them
; Network
M551 P"********" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 ; set steps per mm
M92 E91.0:91.0
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 Z0 S1 ; set minimum Z
; Endstops
M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop
M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop
; Z-Probe
M558 P8 C"zprobe.in" R0.4 H30 F1200 T5000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z0 ; set Z probe trigger value, offset and trigger height
M557 R175 S20 ; define mesh grid
;Filament Sensor
M591 D0 P2 C"e1_stop" S1 ;activate Filament Sensor
; Heaters
M308 S0 A"Heated Bed" P"bedtemp" Y"thermistor" T100000 B4300 C0 R4700 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" Q100 T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 A137.8 B0 C533.3 D1.5 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 P0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 A"E3DV6" P"e0temp" Y"thermistor" T100000 B4300 C0 R4700 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 A0
; Fans
M950 F0 C"fan0" Q24000 ;CPAP create fan 0 on pin fan0 and set its frequency !fan2+exp.pb6 with RPM readout on PB6
M106 C"PartCoolingFan" F65535 P0 S0 H-1 L0.1 ;X0.5 ; set fan 0 value. Thermostatic control is turned off L0.3 X1
M950 F1 C"fan1" Q100 ;HOTEND FAN create fan 1 on pin fan1 and set its frequency
M106 C"HotendFAN" P1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
; Tools
M563 P0 S"E3DV6" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M501 ; load saved parameters from non-volatile memory
T0 ; select first tool
@fcwilt I have tried switching the T0 and T1, did not work, heaters did not function properly.
@Phaedrux Yes the heaters work great actually. no heat creep and they pretty much stay on point even after the error is thrown.
Here is what it does physically:
Printing with PETG
I just tried it again in another slicer, and it did the same thing. So, I am now completely lost.
This is the full Config.g
; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M575 P1 B57600 S1 ;Set baud rate Duet Board
; Delta Settings
M665 L440.49 R185 H405 B185.0 X0 Y0 Z0 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 A0.00 B0.00 ; Put your endstop adjustments here, or let auto calibration find them
; Network
M550 P"TWHPredator" ; Set machine name
;M551 P"T3chn0l0gy" ; Set password
M552 S1 ; Enable network and acquire dynamic address via DHCP
M587 S"Darkweb" P"whatpassword" I192.168.1.253
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Enable Telnet
; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S0 ; Drive 1 goes backwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S0 ; Drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
;Stepper Configuration
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z80 ; Set steps per mm
M92 E91.0:91.0
M906 X2000 Y2000 Z2000 E1000 I13 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
;Normal Speed
M566 X1200 Y1200 Z1200 E3600 ; Set JERK(mm/min)
M203 X18000 Y18000 Z18000 E10000 ; Set maximum speeds (mm/min) 18k is 300mm/s
M201 X3500 Y3500 Z3500 E3500 ; Set accelerations (mm/s^2)
;M204 P2000 T3000 ; set Print accel and travel accel
; Axis Limits
M208 Z0 S1 ; Set minimum Z
; Endstops
M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop
M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop
; Z-Probe
; M558 P8 F1200 R0.4 T5000 H2 A3 I1 ; Set Z probe type to switch and the dive height + speeds 3 Probe Iterations Inverted
M558 C"zprobe.in" P8 R0.4 F1200 H30 T5000
G31 P100 X0 Y0 Z-0.1 ; Set Z probe
M557 R175 S20 ; Define mesh grid
;Filament Sensor
M591 D0 P2 C"e1_stop" S1 ;activate Filament Sensor
; Bed Heater
M308 S0 A"Heated Bed" P"bedtemp" Y"thermistor" T100000 B4300 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M950 H0 C"bedheat" Q100 T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 A137.8 C533.3 D1.5 V24.3 B0 ; Disable bang-bang mode for the bed heater and set PWM limit
M140 H0 P0 ; Create bed Heater
; Extruder Heater
M308 S1 A"E3D V6" P"e0temp" Y"thermistor" T100000 B4300 C0 R4700 ; Temperature Sensor
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 A0 ; Set temperature limit for heater 1 to 280C
;Additional Sensors
M308 S2 A"Chamber" P"e1temp" Y"thermistor" T100000 B3800 C0
; Fans
M950 F1 C"fan1" Q100 ;HOTEND FAN create fan 1 on pin fan1 and set its frequency
M106 C"HotendFAN" P1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F0 C"fan0" Q24000 ;CPAP create fan 0 on pin fan0 and set its frequency !fan2+exp.pb6 with RPM readout on PB6
M106 C"PartCoolingFan" F65535 P0 S0 H-1 L0.1 ;X0.5 ; set fan 0 value. Thermostatic control is turned off L0.3 X1
; Tools
M563 P0 D0 H1 ; Define tool 0 and fan 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
T0 ; select Tool 0
;Extrusion settings
M593 F39.1 ;Resonance Frequency WIP
;Nonlinear extrusion
;M592 D0 A-0.057410915 B0.015877315 ;Nonlinear extrusion WIP
M501 ;load config-override
;Pressure Advance
;M572 D0 S0.22 ;Rosa Silk PLA
;M572 D0 S0.15 ;PLA
;M572 D0 S0.492 ;PETG White 230
M572 D0 S0.08 ;0.8 PLA
; Retraction
M207 S2 F3000 R0 T2200 Z0 ;0.8 PLA
;M207 S2 F1400 R0 T1200 Z0 ;0.8 PETG
;M207 S2 F3000 R0 T2500 Z0.0 ;Silk PLA
;M207 S4 F3600 R0 T2400 Z0.2 ;0.8 PLA
;M207 S2 F3600 R0 T2400 Z0.0 ;ABS
;M207 S2 F3000 R0 T2500 Z0.0 ;Blue Thumann
;M207 S4 F3000 R0 T2400 Z0.0 ;PETG
;M207 S4 F1500 R0 T1200 Z0.0 ;TPU TEST
T0
anyone have any ideas?
End of Config.g
; Tools
M563 P0 D0 H1 ; Define tool 0 and fan 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
T0 ; select Tool 0
;Extrusion settings
M593 F39.1 ;Resonance Frequency WIP
;Nonlinear extrusion
;M592 D0 A-0.057410915 B0.015877315 ;Nonlinear extrusion WIP
M501 ;load config-override
;Pressure Advance
;M572 D0 S0.22 ;Rosa Silk PLA
;M572 D0 S0.15 ;PLA
;M572 D0 S0.492 ;PETG White 230
M572 D0 S0.08 ;0.8 PLA
; Retraction
M207 S2 F3000 R0 T2200 Z0 ;0.8 PLA
;M207 S2 F1400 R0 T1200 Z0 ;0.8 PETG
;M207 S2 F3000 R0 T2500 Z0.0 ;Silk PLA
;M207 S4 F3600 R0 T2400 Z0.2 ;0.8 PLA
;M207 S2 F3600 R0 T2400 Z0.0 ;ABS
;M207 S2 F3000 R0 T2500 Z0.0 ;Blue Thumann
;M207 S4 F3000 R0 T2400 Z0.0 ;PETG
;M207 S4 F1500 R0 T1200 Z0.0 ;TPU TEST
T0
Sample G-code file:
; G-Code generated by Simplify3D(R) Version 4.1.2
; Sep 17, 2020 at 1:27:27 PM
; Settings Summary
; processName,Process1
; applyToModels,PredatorSpoolSupport_ExtendedGuide
; profileName,Predator_Hatchbox_PETG (modified)
; profileVersion,2020-09-14 19:46:39
; baseProfile,M2-E3Dv6-0.4mm
; printMaterial,PLA
; printQuality,Medium
; printExtruders,
; extruderName,Left Extruder
; extruderToolheadNumber,0
; extruderDiameter,0.4
; extruderAutoWidth,1
; extruderWidth,0.48
; extrusionMultiplier,1
; extruderUseRetract,1
; extruderRetractionDistance,1.6
; extruderExtraRestartDistance,0
; extruderRetractionZLift,0.6
; extruderRetractionSpeed,3000
; extruderUseCoasting,1
; extruderCoastingDistance,0
; extruderUseWipe,1
; extruderWipeDistance,5
; primaryExtruder,0
; layerHeight,0.25
; topSolidLayers,5
; bottomSolidLayers,5
; perimeterOutlines,3
; printPerimetersInsideOut,1
; startPointOption,2
; startPointOriginX,0
; startPointOriginY,0
; sequentialIslands,0
; spiralVaseMode,0
; firstLayerHeightPercentage,95
; firstLayerWidthPercentage,100
; firstLayerUnderspeed,0.4
; useRaft,0
; raftExtruder,0
; raftTopLayers,1
; raftBaseLayers,1
; raftOffset,5
; raftSeparationDistance,0.4
; raftTopInfill,80
; aboveRaftSpeedMultiplier,0.3
; useSkirt,1
; skirtExtruder,0
; skirtLayers,1
; skirtOutlines,2
; skirtOffset,5
; usePrimePillar,0
; primePillarExtruder,999
; primePillarWidth,12
; primePillarLocation,7
; primePillarSpeedMultiplier,1
; useOozeShield,0
; oozeShieldExtruder,999
; oozeShieldOffset,2
; oozeShieldOutlines,1
; oozeShieldSidewallShape,1
; oozeShieldSidewallAngle,30
; oozeShieldSpeedMultiplier,1
; infillExtruder,0
; internalInfillPattern,Triangular
; externalInfillPattern,Rectilinear
; infillPercentage,30
; outlineOverlapPercentage,30
; infillExtrusionWidthPercentage,103
; minInfillLength,2
; infillLayerInterval,1
; internalInfillAngles,0,60,-60
; overlapInternalInfillAngles,1
; externalInfillAngles,45,135
; generateSupport,1
; supportExtruder,0
; supportInfillPercentage,15
; supportExtraInflation,1
; supportBaseLayers,3
; denseSupportExtruder,0
; denseSupportLayers,3
; denseSupportInfillPercentage,100
; supportLayerInterval,1
; supportHorizontalPartOffset,0.45
; supportUpperSeparationLayers,4
; supportLowerSeparationLayers,4
; supportType,0
; supportGridSpacing,1
; maxOverhangAngle,60
; supportAngles,0
; temperatureName,Primary Extruder,Heated Bed
; temperatureNumber,0,1
; temperatureSetpointCount,2,2
; temperatureSetpointLayers,1,2,1,2
; temperatureSetpointTemperatures,240,240,80,80
; temperatureStabilizeAtStartup,1,1
; temperatureHeatedBed,0,1
; fanLayers,1
; fanSpeeds,0
; blipFanToFullPower,1
; adjustSpeedForCooling,1
; minSpeedLayerTime,8
; minCoolingSpeedSlowdown,30
; increaseFanForCooling,0
; minFanLayerTime,45
; maxCoolingFanSpeed,100
; increaseFanForBridging,0
; bridgingFanSpeed,100
; use5D,1
; relativeEdistances,1
; allowEaxisZeroing,1
; independentExtruderAxes,0
; includeM10123,0
; stickySupport,1
; applyToolheadOffsets,0
; gcodeXoffset,0
; gcodeYoffset,0
; gcodeZoffset,0
; overrideMachineDefinition,1
; machineTypeOverride,1
; strokeXoverride,260
; strokeYoverride,260
; strokeZoverride,410
; originOffsetXoverride,130
; originOffsetYoverride,130
; originOffsetZoverride,0
; homeXdirOverride,-1
; homeYdirOverride,-1
; homeZdirOverride,1
; flipXoverride,1
; flipYoverride,-1
; flipZoverride,1
; toolheadOffsets,0,0|0,0|0,0|0,0|0,0|0,0
; overrideFirmwareConfiguration,1
; firmwareTypeOverride,RepRap (Marlin/Repetier/Sprinter)
; GPXconfigOverride,r2
; baudRateOverride,250000
; overridePrinterModels,0
; printerModelsOverride
; startingGcode,G28 ; home all axes,G29 S1 ; use previous mesh calibration,
; layerChangeGcode,
; retractionGcode,
; toolChangeGcode,
; endingGcode,G28 ; home all axes,M106 S0 ; turn off cooling fan,M104 S0 ; turn off extruder,M140 S0 ; turn off bed,M84 ; disable motors
; exportFileFormat,gcode
; celebration,0
; celebrationSong,Star Wars
; postProcessing,
; defaultSpeed,3200
; outlineUnderspeed,0.5
; solidInfillUnderspeed,0.75
; supportUnderspeed,0.75
; rapidXYspeed,12000
; rapidZspeed,1200
; minBridgingArea,10
; bridgingExtraInflation,1
; bridgingExtrusionMultiplier,1.4
; bridgingSpeedMultiplier,1.25
; useFixedBridgingAngle,0
; fixedBridgingAngle,0
; applyBridgingToPerimeters,0
; filamentDiameters,1.75|1.75|1.75|1.75|1.75|1.75
; filamentPricesPerKg,24|26|26|26|26|26
; filamentDensities,1.25|1.25|1.25|1.25|1.25|1.25
; useMinPrintHeight,0
; minPrintHeight,12
; useMaxPrintHeight,0
; maxPrintHeight,15
; useDiaphragm,0
; diaphragmLayerInterval,20
; robustSlicing,1
; mergeAllIntoSolid,0
; onlyRetractWhenCrossingOutline,1
; retractBetweenLayers,1
; useRetractionMinTravel,0
; retractionMinTravel,3
; retractWhileWiping,1
; onlyWipeOutlines,1
; avoidCrossingOutline,0
; maxMovementDetourFactor,3
; toolChangeRetractionDistance,0
; toolChangeExtraRestartDistance,0
; toolChangeRetractionSpeed,360
; externalThinWallType,1
; internalThinWallType,2
; thinWallAllowedOverlapPercentage,0
; singleExtrusionMinLength,1
; singleExtrusionMinPrintingWidthPercentage,50
; singleExtrusionMaxPrintingWidthPercentage,200
; singleExtrusionEndpointExtension,0.2
; horizontalSizeCompensation,0
G90
M83
M106 S0
M140 S80
M190 S80
M104 S240 T0
M109 S240 T0
G28 ; home all axes
G29 S1 ; use previous mesh calibration
; process Process1
; layer 1, Z = 0.237
T0
G1 E-1.6000 F3000
; feature skirt
; tool H0.237 W0.480
G1 Z0.600 F1200
G1 X4.089 Y-25.940 F12000
G1 Z0.237 F1200
G1 E1.6000 F3000
G1 X4.911 Y-25.940 E0.0389 F1280
I did, and the issue still happens.
Hi all. I just did the Duet 2 Wifi Upgrade on my printer and I am getting this error when I print any file generated by Simplify3D.
Note: This issue only occurs with S3D, not any other Slicers.
History: The printer was not having this issue with S3D before the Duet 2 Wifi conversion.
This issue will happen at random points during any print. It starts the print fine, then at a random point it will throw this error. Even with the same file, it's random! I have had it happen halfway thru the 1st layer, or on the 10th layer, or the 50th while using the same .gcode file.
There is only 1 extruder, labeled as T0. In the S3D Profile. T1 is the heated bed.
Printer Specs:
Model: Anycubic Predator
Duet 2 Wifi
Paneldue 7i
Smarteffector
BMG extruder
Duet Version: RepRap Firmware 3.1.1
S3D version: 4.1.2
Please Help.