Thank you @Phaedrux , i made every step you said, and now the first layer sticks on the bed.
I swear i leveled the whole printer about 20 times...
Nevermind, it works now and im really happy

Thank you again

Is my heightmap okay, or should i optimize it a bit more?

I have currently one problem, the True Bed Leveling (G32) doesnt move on my leadscrew positions.
When it should move to the first leadscrew (X70 Y10) it moves to (X23 Y26), why does this happen?

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sat Mar 06 2021 14:18:36 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90                                     ; send absolute coordinates...
M83                                     ; ...but relative extruder moves
M550 P"Ender 5"                         ; set printer name

; Network
M552 S1                                 ; enable network
M586 P0 S1                              ; enable HTTP
M586 P1 S0                              ; disable FTP
M586 P2 S0                              ; disable Telnet

; Drives
M569 P0 S1                              ; physical drive 0 goes backwards
M569 P1 S1                              ; physical drive 1 goes backwards
M569 P2 S0                              ; physical drive 2 goes forwards
M569 P3 S1                              ; physical drive 3 goes backwards
M569 P4 S0                              ; physical drive 3 goes backwards
M584 X0 Y1 Z2:4 E3                     	; set drive mapping
M350 X16 Y16 Z16 E16 I1                 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E385.00       ; set steps per mm
M566 X1200.00 Y1200.00 Z24.00 E300.00   ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E6000.00   ; set accelerations (mm/s^2)
M906 X850 Y800 Z800 E1000 I50           ; set motor currents (mA) and motor idle factor in per cent
M671 X70:70 Y10:200 S0.5 				; leadscrews at left (connected to Z) and right (connected to E1) of X axis
M84 S30                                 ; Set idle timeout


; Axis Limits
M208 X0 Y0 Z0 S1                        ; set axis minima
M208 X220 Y220 Z300 S0                  ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                     ; configure active-high endstop for high end on X via pin xstop
M574 Y1 S1 P"ystop"                     ; configure active-high endstop for high end on Y via pin ystop
M574 Z1 S2                              ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"exp.heater3"                  ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000     ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X44 Y-17 Z1.85                 ; set Z probe trigger value, offset and trigger height
M557 X15:195 Y15:195 S20                ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" B4092 R4700 	; configure sensor 0 as PT1000 on pin bedtemp
M950 H0 C"bedheat" T0   						; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.310 C384.6 D1.73 S1.00 V23.5			; disable bang-bang mode for the bed heater and set PWM limit      	
M140 H0                                 		; map heated bed to heater 0
M143 H0 S120                            		; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" B4092 R4700     ; configure sensor 1 as PT1000 on pin e0temp
M950 H1 C"e0heat" T1                    		; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 R3.417 C47.1 D3.33 S1.00 V24.0    		; disable bang-bang mode for heater  and set PWM limit
M143 H1 S275                            		; set temperature limit for heater 1 to 275C

; Fans
M950 F0 C"fan0" Q500                    ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                          ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                    ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                       ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500                    ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1:0 T45                     ; set fan 2 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                        ; define tool 0
G10 P0 X0 Y0 Z0                         ; set tool 0 axis offsets
G10 P0 R0 S0                            ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined
; BLTouch startup
G4 S2									; Pause a couple seconds
M280 P64 S160							; Clear any alarms
G4 S2									; Pause a couple seconds
M402									; retract pin just in case	

M912 P0 S-11							; CPU Temp Calib

Hello my friends,

i have a huge problem with my ender 5, the first layer wont stick anymore.
To explain how it all happened. I printed something and when it was finished I wanted to take it off the heatbed and tore it too much, since nothing want stuck on the heatbed.

I tried leveling and it really did at least 20 times, then I bought this and it didn't help either. I also exchanged the BLTouch without success.

Then I updated the firmware and since then the belt is skipping some gears when homeing.

I added a Z-axis to the Ender 5 and the automatic adjustment of G32 doesn't work, so I put the second Z-motor on Z2 and adjusted it manually.

It would be nice if someone looks at my configuration, maybe I did something wrong. Would be really nice.

My setup
Printer: Ender 5
Z-Probe: BLTouch
Z-Axis : 2
Hotend: Micro-Swiss All Metal Hotend
Extruder: BMG Extruder

Start G-Code

G28 XY
M561 ; Clear bed transforms
G28 Z ; Home Z
G29 S1 ; Load mesh leveling from SD card
G92 E0 ; reset extrusion distance
G1 Z0.2 F1000.0
G1 X60.0 E9.0 F1000.0 ; priming
G1 X125.0 E12.5 F1000.0 ; priming
G1 Z0.5 F1000.0
G92 E0 ; reset extrusion distance

End G-Code

G10 P0 R-273.15 S-273.15     ; Turn off Tool0
G10 P1 R-273.15 S-273.15     ; Turn off Tool1
M140 S-273.15                ; Turn off Bed
M106 S0                      ; Object fan off
G1 Z210                      ; Move Z to Z210
G92 E0                       ; Zero Extruder
G1 E-2 F300                  ; Retract 2mm
G92 E0                       ; Zero Extruder
G28 XY                       ; Home XY
M84                          ; All motors Off

Config Files
retractprobe.g
homez.g
homey.g
homex.g
homeall.g
heightmap.csv
deployprobe.g
config-override.g
config.g
bed.g

Thanks that worked for me, downgrading solves it.

Thank you guys, i couldn't find any option under Cura to set the center at X110 Y110.
I set the axis limits to M208 X-25 Y20 Z0 S1 and it seems to be centered now.

Is visible on the Dashboard and also on the Status page under Fans

Duet Web Control 2.1.1
Board: Duet WiFi 1.02
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 2.05.1 (2020-02-09b1)
Duet WiFi Server Version: 1.23

Thank you, im using Cura 4.4!
This are my settings for my printer, and normaly it should be okay (i think)
Cura Settings

Hi,

i have an another issue, my printer dont start at the center of the bed, and i can't find the issue in my config.

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Apr 12 2020 21:12:30 GMT+0200 (Mitteleuropäische Sommerzeit)
 
; General preferences
G90                                      ; send absolute coordinates...
M83                                      ; ...but relative extruder moves
M550 P"BLV AM8"                          ; set printer name
 
; Network
M552 S1                                  ; enable network
M586 P0 S1                               ; enable HTTP
M586 P1 S0                               ; disable FTP
M586 P2 S0                               ; disable Telnet
 
; Drives
M569 P0 S0                               ; physical drive 0 goes backwards
M569 P1 S0                               ; physical drive 1 goes backwards
M569 P2 S1                               ; physical drive 2 goes forwards
M569 P3 S1                               ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                         ; set drive mapping
M350 X16 Y16 Z16 E16 I1                  ; configure microstepping with interpolation
M92 X80.456 Y80.6956 Z408.1451 E385.00   ; set steps per mm
M566 X600.00 Y600.00 Z18.00 E300.00      ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E6000.00  ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z100.00 E10000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E1000 I50            ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                  ; Set idle timeout
 
; Axis Limits
M208 X-33 Y-10 Z0 S1                     ; set axis minima
M208 X220 Y220 Z240 S0                   ; set axis maxima
 
; Endstops
M574 X1 Y1 S0                            ; set active low and disabled endstops
M574 Z1 S2                               ; set endstops controlled by probe
 
; Z-Probe
M307 H3 A-1 C-1 D-1			             ; Disable the 3th Heater to free up PWM channel 5 on the Duex board.
M558 P9 H3 F120 T6000 A10 S0.003 B1 R0.5 ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X30.44 Y-9.48 Z0.7              ; set Z probe trigger value, offset and trigger height
M557 X5:200 Y5:200 S20                   ; define mesh grid
 
; Heaters
M307 H0 B0 S1.00                         ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4725 C7.060000e-8 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S130                             ; set temperature limit for heater 0 to 130C
M305 P1 T100000 B4725 C7.060000e-8 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S275                             ; set temperature limit for heater 1 to 275C
 
; Fans
M106 P0 S0 I0 F500 H-1                   ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1                   ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H-1                   ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
 
; Tools
M563 P0 D0 H1 F0                         ; define tool 0
G10 P0 X0 Y0 Z0                          ; set tool 0 axis offsets
G10 P0 R0 S0                             ; set initial tool 0 active and standby temperatures to 0C
 
; BLTouch startup
G4 S2					                 ; Pause a couple seconds
M280 P64 S160				             ; Clear any alarms
G4 S2					                 ; Pause a couple seconds
M402					                 ; retract pin just in case	
 
M912 P0 S3.4
 
; Miscellaneous
T0                                       ; select first tool

Hi,

i just want to configure my new printer and the fan control shows up to 8 fans, but i have only the standard duet 2 wifi without an duex extension board.

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Apr 12 2020 21:12:30 GMT+0200 (Mitteleuropäische Sommerzeit)

; General preferences
G90                                      ; send absolute coordinates...
M83                                      ; ...but relative extruder moves
M550 P"BLV AM8"                          ; set printer name

; Network
M552 S1                                  ; enable network
M586 P0 S1                               ; enable HTTP
M586 P1 S0                               ; disable FTP
M586 P2 S0                               ; disable Telnet

; Drives
M569 P0 S0                               ; physical drive 0 goes backwards
M569 P1 S0                               ; physical drive 1 goes backwards
M569 P2 S1                               ; physical drive 2 goes forwards
M569 P3 S1                               ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                         ; set drive mapping
M350 X16 Y16 Z16 E16 I1                  ; configure microstepping with interpolation
M92 X80.456 Y80.6956 Z408.1451 E385.00   ; set steps per mm
M566 X600.00 Y600.00 Z18.00 E300.00      ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E6000.00  ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z100.00 E10000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E1000 I50            ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                  ; Set idle timeout

; Axis Limits
M208 X-33 Y-10 Z0 S1                     ; set axis minima
M208 X220 Y220 Z240 S0                   ; set axis maxima

; Endstops
M574 X1 Y1 S0                            ; set active low and disabled endstops
M574 Z1 S2                               ; set endstops controlled by probe

; Z-Probe
M307 H3 A-1 C-1 D-1			             ; Disable the 3th Heater to free up PWM channel 5 on the Duex board.
M558 P9 H3 F120 T6000 A10 S0.003 B1 R0.5 ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X30.44 Y-9.48 Z0.7              ; set Z probe trigger value, offset and trigger height
M557 X5:200 Y5:200 S20                   ; define mesh grid

; Heaters
M307 H0 B0 S1.00                         ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4725 C7.060000e-8 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S130                             ; set temperature limit for heater 0 to 130C
M305 P1 T100000 B4725 C7.060000e-8 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S275                             ; set temperature limit for heater 1 to 275C

; Fans
M106 P0 S0 I0 F500 H-1                   ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1                   ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H-1                   ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0                         ; define tool 0
G10 P0 X0 Y0 Z0                          ; set tool 0 axis offsets
G10 P0 R0 S0                             ; set initial tool 0 active and standby temperatures to 0C

; BLTouch startup
G4 S2					                 ; Pause a couple seconds
M280 P64 S160				             ; Clear any alarms
G4 S2					                 ; Pause a couple seconds
M402					                 ; retract pin just in case	

M912 P0 S3.4

; Miscellaneous
T0                                       ; select first tool

Is my configuration wrong?

Thanks for help

Thanks, i changed it to 117 to the center of the bed.

My mesh grid is set on X to max 180, why does it exceed?
M557 X5:180 Y5:215 S10

And why does it start at X: 49.0 Y:22.0 and not from 5 ?

@Phaedrux i hope its everything
homez.g homey.g homex.g homedelta.g homeall.g bed.g