Posts made by trout thug

Ok just a quick google search and M569 P3 S0 made the difference. I'm still too close to the buildplate but there is pla flowing.

Again much thanks,
Bill in colorado

Ah haa, I just found another problem. My extruder motor is going in the wrong direction. After forcing the pla thru I was able to get some plastic on the buildplate so how does one change the extruder in the correct direction and I believe I can finally over 3 months print my test cube. I can't believe that it is something as simple as that. But with the z height change I can atleast now get the plastic thru.

I'm getting giddy with the closeness of this project.

Thanks adavidm,
Bill in colorado

So another step closer and more tweaking. Its a smart effector and 200 temp. The problem now is that the hot end is too close to the build surface. Its not allowing the pla to come out of the end. I run the automatic bed leveling and from there its just too close to the build surface. I will try tomorrow again to go over the initial steps of getting the bed level but the change in the M208 command got me closer.

So I'll try again tomorrow, and thanks,
Bill in colorado

Ok its closer now the extruder motor isn't feeding the pla, alot of clicking from the motor so I will investigate to see why it isn't feeding the pla into the hot end.

But it is slowly looking like it should and when it tried to print the hot end was much closer to the build plate.

Getting excited and thank you to all who have helped. There is no way that I would be able to do this on my own. So thank you again.
Bill in colorado

@adavidm said in So close to printing getting Error: G1/G2/G3::

M208 Z-0.1 S1

Ok sorry I have been at my sons lacrosse tournament in California, I'm booting up my delta right now with the change. I'll report back when I make the changes.

Again thanks,
Bill in colorado

Ah I knew there was something easy.

It doesn't make sense to me but here it is.

;TIME:1122
;Filament used: 0.614537m
;Layer height: 0.3
;Generated with Cura_SteamEngine 3.5.1
T0
M190 S60
M104 S200
M109 S200
M82 ;absolute extrusion mode
G28 ;Home
G32
;G29 S1
G92 E0 ; Set the extruder to zero
G1 E8 ; Prime the nozzle
M83 ;relative extrusion mode
G1 F1500 E-6.5
;LAYER_COUNT:67
;LAYER:0
M107
G0 F3600 X17.8 Y-10 Z0.3
;TYPE:SKIRT
G1 F1500 E6.5
G1 F1800 X17.8 Y10 E0.37621
G1 X17.76 Y10.789 E0.01486
G1 X17.641 Y11.569 E0.01484
G1 X17.443 Y12.334 E0.01486
G1 X17.169 Y13.074 E0.01484
G1 X16.821 Y13.783 E0.01486
G1 X16.403 Y14.454 E0.01487
G1 X15.92 Y15.078 E0.01484
G1 X15.377 Y15.651 E0.01485
G1 X14.778 Y16.166 E0.01486
G1 X14.13 Y16.617 E0.01485
G1 X13.439 Y17.001 E0.01487
G1 X12.714 Y17.313 E0.01485
G1 X11.961 Y17.55 E0.01485
G1 X11.187 Y17.709 E0.01486
G1 X10.402 Y17.79 E0.01484
G1 X10 Y17.8 E0.00756
G1 X-10 Y17.8 E0.37621
G1 X-10.789 Y17.76 E0.01486
G1 X-11.569 Y17.641 E0.01484
G1 X-12.334 Y17.443 E0.01486
G1 X-13.074 Y17.169 E0.01484
G1 X-13.783 Y16.821 E0.01486
G1 X-14.454 Y16.403 E0.01487
G1 X-15.078 Y15.92 E0.01484
G1 X-15.651 Y15.377 E0.01485
G1 X-16.166 Y14.778 E0.01486
G1 X-16.617 Y14.13 E0.01485
G1 X-17.001 Y13.439 E0.01487
G1 X-17.313 Y12.714 E0.01485
G1 X-17.55 Y11.961 E0.01485
G1 X-17.709 Y11.187 E0.01486
G1 X-17.79 Y10.402 E0.01484
G1 X-17.8 Y10 E0.00756
G1 X-17.8 Y-10 E0.37621
G1 X-17.76 Y-10.789 E0.01486
G1 X-17.641 Y-11.569 E0.01484
G1 X-17.443 Y-12.334 E0.01486
G1 X-17.169 Y-13.074 E0.01484
G1 X-16.821 Y-13.783 E0.01486
G1 X-16.403 Y-14.454 E0.01487
G1 X-15.92 Y-15.078 E0.01484
G1 X-15.377 Y-15.651 E0.01485
G1 X-14.778 Y-16.166 E0.01486
G1 X-14.13 Y-16.617 E0.01485
G1 X-13.439 Y-17.001 E0.01487
G1 X-12.714 Y-17.313 E0.01485
G1 X-11.961 Y-17.55 E0.01485
G1 X-11.187 Y-17.709 E0.01486
G1 X-10.402 Y-17.79 E0.01484
G1 X-10 Y-17.8 E0.00756
G1 X10 Y-17.8 E0.37621
G1 X10.789 Y-17.76 E0.01486
G1 X11.569 Y-17.641 E0.01484
G1 X12.334 Y-17.443 E0.01486
G1 X13.074 Y-17.169 E0.01484
G1 X13.783 Y-16.821 E0.01486
G1 X14.454 Y-16.403 E0.01487
G1 X15.078 Y-15.92 E0.01484
G1 X15.651 Y-15.377 E0.01485
G1 X16.166 Y-14.778 E0.01486
G1 X16.617 Y-14.13 E0.01485
G1 X17.001 Y-13.439 E0.01487
G1 X17.313 Y-12.714 E0.01485
G1 X17.55 Y-11.961 E0.01485
G1 X17.709 Y-11.187 E0.01486
G1 X17.79 Y-10.402 E0.01484
G1 X17.8 Y-10 E0.00756
G0 F3600 X17.4 Y-10
G1 F1800 X17.4 Y10 E0.37621
G1 X17.36 Y10.768 E0.01447
G1 X17.241 Y11.528 E0.01447
G1 X17.043 Y12.271 E0.01446
G1 X16.769 Y12.99 E0.01447
G1 X16.422 Y13.676 E0.01446
G1 X16.006 Y14.323 E0.01447
G1 X15.525 Y14.923 E0.01447
G1 X14.984 Y15.47 E0.01447
G1 X14.389 Y15.958 E0.01448
G1 X13.747 Y16.381 E0.01446
G1 X13.064 Y16.736 E0.01448
G1 X12.349 Y17.017 E0.01445
G1 X11.607 Y17.223 E0.01449
G1 X10.849 Y17.351 E0.01446
G1 X10 Y17.4 E0.016
G1 X-10 Y17.4 E0.37621
G1 X-10.768 Y17.36 E0.01447
G1 X-11.528 Y17.241 E0.01447
G1 X-12.271 Y17.043 E0.01446
G1 X-12.99 Y16.769 E0.01447
G1 X-13.676 Y16.422 E0.01446
G1 X-14.323 Y16.006 E0.01447
G1 X-14.923 Y15.525 E0.01447
G1 X-15.47 Y14.984 E0.01447
G1 X-15.958 Y14.389 E0.01448
G1 X-16.381 Y13.747 E0.01446
G1 X-16.736 Y13.064 E0.01448
G1 X-17.017 Y12.349 E0.01445
G1 X-17.223 Y11.607 E0.01449
G1 X-17.351 Y10.849 E0.01446
G1 X-17.4 Y10 E0.016
G1 X-17.4 Y-10 E0.37621
G1 X-17.36 Y-10.768 E0.01447
G1 X-17.241 Y-11.528 E0.01447
G1 X-17.043 Y-12.271 E0.01446
G1 X-16.769 Y-12.99 E0.01447
G1 X-16.422 Y-13.676 E0.01446
G1 X-16.006 Y-14.323 E0.01447
G1 X-15.525 Y-14.923 E0.01447
G1 X-14.984 Y-15.47 E0.01447
G1 X-14.389 Y-15.958 E0.01448
G1 X-13.747 Y-16.381 E0.01446
G1 X-13.064 Y-16.736 E0.01448
G1 X-12.349 Y-17.017 E0.01445
G1 X-11.607 Y-17.223 E0.01449
G1 X-10.849 Y-17.351 E0.01446
G1 X-10 Y-17.4 E0.016
G1 X10 Y-17.4 E0.37621
G1 X10.768 Y-17.36 E0.01447
G1 X11.528 Y-17.241 E0.01447
G1 X12.271 Y-17.043 E0.01446
G1 X12.99 Y-16.769 E0.01447
G1 X13.676 Y-16.422 E0.01446
G1 X14.323 Y-16.006 E0.01447
G1 X14.923 Y-15.525 E0.01447
G1 X15.47 Y-14.984 E0.01447
G1 X15.958 Y-14.389 E0.01448
G1 X16.381 Y-13.747 E0.01446
G1 X16.736 Y-13.064 E0.01448
G1 X17.017 Y-12.349 E0.01445
G1 X17.223 Y-11.607 E0.01449
G1 X17.351 Y-10.849 E0.01446
G1 X17.4 Y-10 E0.016
G0 F3600 X17 Y-10
G1 F1800 X17 Y10 E0.37621
G1 X16.96 Y10.747 E0.01407
G1 X16.841 Y11.485 E0.01406
G1 X16.643 Y12.207 E0.01408
G1 X16.37 Y12.903 E0.01406
G1 X16.023 Y13.566 E0.01408
G1 X15.608 Y14.189 E0.01408
G1 X15.129 Y14.763 E0.01406
G1 X14.592 Y15.284 E0.01407
G1 X14.002 Y15.743 E0.01406
G1 X13.366 Y16.138 E0.01408
G1 X12.692 Y16.462 E0.01407
G1 X11.987 Y16.712 E0.01407
G1 X11.259 Y16.886 E0.01408
G1 X10.517 Y16.981 E0.01407
G1 X10 Y17 E0.00973
G1 X-10 Y17 E0.37621
G1 X-10.747 Y16.96 E0.01407
G1 X-11.485 Y16.841 E0.01406
G1 X-12.207 Y16.643 E0.01408
G1 X-12.903 Y16.37 E0.01406
G1 X-13.566 Y16.023 E0.01408
G1 X-14.189 Y15.608 E0.01408
G1 X-14.763 Y15.129 E0.01406
G1 X-15.284 Y14.592 E0.01407
G1 X-15.743 Y14.002 E0.01406
G1 X-16.138 Y13.366 E0.01408
G1 X-16.462 Y12.692 E0.01407
G1 X-16.712 Y11.987 E0.01407
G1 X-16.886 Y11.259 E0.01408
G1 X-16.981 Y10.517 E0.01407
G1 X-17 Y10 E0.00973
G1 X-17 Y-10 E0.37621
G1 X-16.96 Y-10.747 E0.01407
G1 X-16.841 Y-11.485 E0.01406
G1 X-16.643 Y-12.207 E0.01408
G1 X-16.37 Y-12.903 E0.01406
G1 X-16.023 Y-13.566 E0.01408
G1 X-15.608 Y-14.189 E0.01408
G1 X-15.129 Y-14.763 E0.01406
G1 X-14.592 Y-15.284 E0.01407
G1 X-14.002 Y-15.743 E0.01406
G1 X-13.366 Y-16.138 E0.01408
G1 X-12.692 Y-16.462 E0.01407
G1 X-11.987 Y-16.712 E0.01407
G1 X-11.259 Y-16.886 E0.01408
G1 X-10.517 Y-16.981 E0.01407
G1 X-10 Y-17 E0.00973
G1 X10 Y-17 E0.37621
G1 X10.747 Y-16.96 E0.01407
G1 X11.485 Y-16.841 E0.01406
G1 X12.207 Y-16.643 E0.01408
G1 X12.903 Y-16.37 E0.01406
G1 X13.566 Y-16.023 E0.01408
G1 X14.189 Y-15.608 E0.01408
G1 X14.763 Y-15.129 E0.01406
G1 X15.284 Y-14.592 E0.01407
G1 X15.743 Y-14.002 E0.01406
G1 X16.138 Y-13.366 E0.01408
G1 X16.462 Y-12.692 E0.01407
G1 X16.712 Y-11.987 E0.01407
G1 X16.886 Y-11.259 E0.01408
G1 X16.981 Y-10.517 E0.01407
G1 X17 Y-10 E0.00973
G0 F3600 X16.6 Y-10
G1 F1800 X16.6 Y10 E0.37621
G1 X16.56 Y10.725 E0.01366
G1 X16.441 Y11.442 E0.01367
G1 X16.243 Y12.141 E0.01367
G1 X15.97 Y12.814 E0.01366
G1 X15.625 Y13.453 E0.01366
G1 X15.211 Y14.05 E0.01367
G1 X14.735 Y14.598 E0.01365
G1 X14.201 Y15.091 E0.01367
G1 X13.616 Y15.521 E0.01366
G1 X12.987 Y15.885 E0.01367
G1 X12.322 Y16.178 E0.01367
G1 X11.629 Y16.396 E0.01367
G1 X10.917 Y16.536 E0.01365
G1 X10 Y16.6 E0.01729
G1 X-10 Y16.6 E0.37621
G1 X-10.725 Y16.56 E0.01366
G1 X-11.442 Y16.441 E0.01367
G1 X-12.141 Y16.243 E0.01367

There is a huge amt of code from there, if you need more let me know and I hope this helps someone. I must be missing something very small.

Thanks again to all or any who read and or help,
Bill in colorado

Ok so this is going to sound stupid. I don't know how to look that up. Any ideas or tips?

Sorry for the noob problem, this is all new to me.
Bill in colorado

Howdy again,
Ok I'm soooo close I can just about taste it. I can get my delta (old monoprice garbage) to heat up, auto home, and run thru the delta auto calibration. And it gives me that 3d picture of my very uneven glass. When I go to print it runs thru the auto calibration setup and then gives me the "Error: G1/G2/G3: intermediate position outside machine limits ." I know that I'm so close to printing that I just must be missing something. I'll include my cura settings and config files.

Starting G code from Cura:
G28 ;Home
G32
;G29 S1
G92 E0 ; Set the extruder to zero
G1 E8 ; Prime the nozzle

Config files
; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves

;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.
M665 R105.6 L215 B85 H310 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z80 E663 ; Set steps per mm
M566 X1200 Y1200 Z1200 E1200 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z18000 E1200 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z1000 E1000 ; Set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z310 S1 ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S1 ; Set active high endstops

; Z-Probe
M558 P5 R0.4 H5 F1200 T6000 ; Set Z probe type to effector and the dive height + speeds
G31 P100 X0 Y0 Z-0.1 ; Set Z probe trigger value, offset and trigger height
M557 R85 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory

So I'm again back just asking for some help from the Duet Wifi heros.

Thanks again for even looking and I can't wait to have the smell of pla printing on this machine!!!

Bill in colorado

Ok so I can get heat to the delta and I can probe all around and get values. I wanted to do a test cube and I get the following error 205 command is not supported. I'm using cura (the newest version), newest firmware, and duet wifi. I also heard some strange noises coming from my delta. I hope I'm getting closer but I'm glad I can get the heater to work and the smart effector to also work.

So close to printing I can taste it,
Bill in colorado

I'm assuming yes since I got it from Filastruder, I wanted to keep the $$ with the folks that helped developed it and not a cheap clone.

Again much thanks,
Bill in colorado

Ok we are heating, after some probing the soldering job on the duet board was poor on the terminal block, on the negative side of E0. I'm now heating the end and onto some other calibration stuff. (At least my wiring was ok, so I'm not super down on myself;)

Thanks sooo much for all of your help, because without it my delta would of been sold by now. My hope now is to get a print and go from there.

You guys are awesome.
Bill in colorado

Ok can I assume that I can test from the duet board 1st from the bottom of the board (below the terminal block) on the + and - that I should get a complete circuit? (sorry about the basic question.) If I don't and the wires show a complete circuit could I have a problem with my connection with the block?

Thank again soo much,
Bill in colorado

And here is my H1 values
M307 H1
Heater 1 model: gain 340.0, time constant 140.0, dead time 5.5, max PWM 1.00, calibration voltage 0.0, mode PID, inverted no, frequency default
Computed PID parameters for setpoint change: P13.4, I0.482, D51.4
Computed PID parameters for load change: P13.4

Heater Error problems and confusion.
Howdy again, I've got the replacement smart effector and its working well now so that is a good thing. But even as before I cannot for the life of me to get the hot end heater working. I'm on a 12v power supply. I've tried new thermistor and a new premium E3d heater cartridge 12v 30w and re wired the 6 molex plug again and it still shows that I'm heating up too slow. I've tried both E0 and E1 plugs in the main duet wifi board and it still shows the error. I've tried the following as well:

11:32:14 AM
Auto tune cancelled because temperature is not increasing
11:31:37 AM
Auto tune phase 1, heater on
11:31:32 AM
M303 H1 S240
Auto tuning heater 1 using target temperature 240.0°C and PWM 1.00 - do not leave printer unattended
11:31:02 AM
M307 H0 D30
11:28:08 AM
Auto tune cancelled because temperature is not increasing
11:27:31 AM
Auto tune phase 1, heater on
11:27:26 AM
M303 H1 S240
Auto tuning heater 1 using target temperature 240.0°C and PWM 1.00 - do not leave printer unattended
11:25:19 AM
M307 H#
Heater 0 model: gain 90.0, time constant 700.0, dead time 10.0, max PWM 1.00, calibration voltage 0.0, mode bang-bang, inverted no, frequency default.

My config file is here. I'm running the newest firmware. I do see the light try and come on with the board but then shuts off when I get the error.

Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory

Any ideas on what is wrong. I used the RRF config tool and I again must be missing something. I'm getting closer but still so far away.

Thanks for looking and any help is awesome.
Bill in colorado

Nope I'm fresh out of the vibrating tables and I didn't feel any seismic activity . I'll contact filastruder.

Thanks again to all for your help,
Bill in colorado

And here is what I see on my screen. https://youtu.be/GqBXmWTTms4.

Again thanks,
Bill in colorado

https://youtu.be/kf014E1zGjM . I turn on the power, it blinks x2 and then just goes funky. I will try to upload the pict of the z probe values on there shortly.

bill in colorado

I just tried to change the sensitivity all the way up to 200, but the green led and values keep changing. I unplugged the 6 way molex connector on the effector to eliminate the interference and I still keep getting the varying values and led's random blinking. I will go back and again check my crimping but with the fans not even connected and nothing else that could cause interference, what could I be missing? Or do I have a bad effector??

Again I thank you for reading and helping. I did take a video but I don't know how I could attach the file to show the blinking and random z values.
Bill in colorado

Howdy,
I've re crimped all of it and now I get the values from 0 (which I did go hurray) to 1000. As the smart efffector when 1st turned on it blinks twice and then with no fans turned on it just randomly blinks. The values are all over the area from 0 to 1000 on the duet web control screen. I'm going to go back on check all my crimps but I must be missing something. When you gently tap the hot end you briefly see it turn on but then goes back to the random blinking with strange 0- 1000 z probe values.

Again so much thanks to any who read this. (my wife thinks I'm crazy for trying this;)
Bill in colorado

Howdy,
I'm totally new to this idea and I have gone over the info a few times and I'm totally stuck. I can get my Delta printer (which was a micromaker D1 delta) to home but I must be doing something wrong. My G31 parameter is coming out 1000. I tried the auto calibrate option but it also doesn't work. I'm very sorry if this is a basic question but I'm a medical guy and this is scary and fun at the same time. I'll include my info from my config that I tried on the rep rap config.

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Wed Oct 03 2018 11:02:08 GMT-0600 (Mountain Daylight Time)

; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves

;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.
M665 R95 L215 B80 H300 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them

; Network
M550 PThe Delta ; Set machine name
M552 S1 ; Enable network
M587 S"Help Ive Fallen" P"muskistoo" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S1 ; Enable FTP
M586 P2 S1 ; Enable Telnet

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z80 E663 ; Set steps per mm
M566 X1200 Y1200 Z1200 E1200 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z18000 E1200 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z1000 E1000 ; Set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z0 S1 ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S1 ; Set active high endstops

; Z-Probe
M558 P5 R0.4 H5 F1200 T6000 ; Set Z probe type to effector and the dive height + speeds
G31 P100 X0 Y0 Z-0.1 ; Set Z probe trigger value, offset and trigger height
M557 R80 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S260 ; Set temperature limit for heater 1 to 260C

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings
M591 D0 C3 P1 E6.0

And here is my bed file.
; bed.g
; called to perform automatic delta calibration via G32
;
; generated by RepRapFirmware Configuration Tool on Wed Oct 03 2018 11:02:08 GMT-0600 (Mountain Daylight Time)
M561 ; clear any bed transform
G28 ; home all towers
; Probe the bed at 3 peripheral and 3 halfway points, and perform 3-factor auto compensation
; Before running this, you should have set up your Z-probe trigger height to suit your build, in the G31 command in config.g.
G30 P0 X0 Y79.9 H0 Z-99999
G30 P1 X69.2 Y-39.95 H0 Z-99999
G30 P2 X-69.2 Y-39.95 H0 Z-99999
G30 P3 X0 Y39.9 H0 Z-99999
G30 P4 X34.55 Y-19.95 H0 Z-99999
G30 P5 X-34.55 Y-19.95 H0 Z-99999
G30 P6 X0 Y0 H0 Z-99999 S3
; Use S-1 for measurements only, without calculations. Use S4 for endstop heights and Z-height only. Use S6 for full 6 factors
; If your Z probe has significantly different trigger heights depending on XY position, adjust the H parameters in the G30 commands accordingly. The value of each H parameter should be (trigger height at that XY position) - (trigger height at centre of bed)

Thanks for any help or ideas on where to start.

Bill in colorado