Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    CR-10S5 Firmware

    Scheduled Pinned Locked Moved Unsolved
    Firmware installation
    15
    145
    8.2k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Gost101undefined
      Gost101
      last edited by

      Is there a way to make the axis move faster besides changing the steps/mm?

      1 Reply Last reply Reply Quote 0
      • Phaedruxundefined
        Phaedrux Moderator
        last edited by

        Change the feed rate of the move.

        Z-Bot CoreXY Build | Thingiverse Profile

        1 Reply Last reply Reply Quote 0
        • Gost101undefined
          Gost101
          last edited by

          Which command is that?

          1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator
            last edited by

            That's the F parameter of the G1 moves

            Z-Bot CoreXY Build | Thingiverse Profile

            1 Reply Last reply Reply Quote 0
            • Gost101undefined
              Gost101
              last edited by

              Here is the latest config files.
              I need to print the BLTouch mount before I can begin using it.
              Everything heats up, however I'm having trouble with the e3D Volcano extruding (I just bough a Bondtech Extruder to hopeful solve this as the stock extruder is skipping. I will try to see if the hotend is clogged, I don't think it is due to being a e3D nozzle X.
              Everything works at the moment, so I will attempt a benchy.

              Config.g: config.g

              ;config.g
              ; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 MST (6:00PM for Civs). 
              ; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr-10s5-firmware/37
              ; Contact gost1017@gmail.com for more help.
              
              ; General preferences
              G90                                      ; send absolute coordinates...
              M83                                      ; ...but relative extruder moves
              M550 P"A.C.E."                           ; set printer name
              M669 K0                                  ; select Cartesian mode
              
              ; Network
              M551 P"12345"                            ; set password
              M552 S1                                  ; enable network
              M586 P0 S1                               ; enable HTTP
              M586 P1 S0                               ; disable FTP
              M586 P2 S0                               ; disable Telnet
              
              ; Drives
              M569 P0 S1                               ; X physical drive 0 goes forwards
              M569 P1 S1                               ; Y physical drive 1 goes forwards
              M569 P2 S0                               ; Z physical drive 2 goes backwards
              M569 P2 S0                               ; Z physical drive 2 goes backwards
              M569 P3 S1                               ; E physical drive 3 goes forwards
              M584 X0 Y1 Z2 E3                         ; set drive mapping
              M350 X16 Y16 Z16 E16 I1                  ; configure microstepping with interpolation
              M92 X80.00 Y78.00 Z400.00 E420.00        ; set steps per mm
              M566 X900.00 Y900.00 Z1400.00 E120.00    ; set maximum instantaneous speed changes (mm/min)
              M203 X6000.00 Y6000.00 Z1400.00 E1200.00 ; set maximum speeds (mm/min)
              M201 X500.00 Y500.00 Z1400.00 E250.00    ; set accelerations (mm/s^2)
              M906 X800 Y800 Z8000 E800 I30            ; set motor currents (mA) and motor idle factor in per cent
              M84 S30                                  ; Set idle timeout
              
              ; Axis Limits
              M208 X0:500 Y0:500 Z0:500                ; set axis maxima
              
              ; Endstops
              M574 X1 Y1 Z1 S1                         ; set active high endstops
              
              ; Z-Probe
              M558 P0 H5 F120 T6000                    ; disable Z probe but set dive height, probe speed and travel speed
              M557 X15:215 Y15:195 S20                 ; define mesh grid
              
              ; Heaters
              M305 P0 T100000 B4138 R4700              ; set thermistor + ADC parameters for heater 0
              M143 H0 S120                             ; set temperature limit for heater 0 to 120C
              M305 P1 T100000 B4138 R4700              ; set thermistor + ADC parameters for heater 1
              M143 H1 S280                             ; set temperature limit for heater 1 to 280C
              
              ; Fans
              M106 P0 S0 I0 F500 H-1                   ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
              M106 P1 S1 I0 F500 H1 T45                ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
              
              ; Tools
              M563 P0 D0 H1 F0                         ; define tool 0
              G10 P0 X0 Y0 Z0                          ; set tool 0 axis offsets
              G10 P0 R0 S0                             ; set initial tool 0 active and standby temperatures to 0C
              
              ; Custom settings are not defined
              

              Home All: homeall.g

              ; homeall.g
              ; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 (6:00PM for Civs). 
              ; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr-10s5-firmware/37
              ; Contact gost1017@gmail.com for more help.
              ; Y-Axis
              G91                ; relative positioning
              G1 S1 Y-505 F3000  ; move quickly to Y axis endstop and stop there (first pass)
              G1 Y5 F1000        ; go back a few mm
              G1 S1 Y-505 F360   ; move slowly to Y axis endstop once more (second pass)
              G90                ; absolute positioning
              ; X-Axis
              G91                ; relative positioning
              G1 S1 X-505 F1800  ; move quickly to X axis endstop and stop there (first pass)
              G1 X5 F6000        ; go back a few mm
              G1 S1 X-505 F360   ; move slowly to X axis endstop once more (second pass)
              G90                ; absolute positioning
              ; Z-Axis
              G91                ; relative positioning
              G1 S1 Z-505 F10000 ; move Z down until the endstop is triggered
              G92 Z0             ; set Z position to axis minimum (you may want to adjust this)
              G1 Z3 F800         ; go back a few mm
              G1 S1 Z-505 F80    ; move slowly to X axis endstop once more (second pass)
              G90                ; absolute positioning
              

              Home X: homex.g

              ; homex.g
              ; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 MST (6:00PM for Civs). 
              ; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr-10s5-firmware/37
              ; Contact gost1017@gmail.com for more help.
              G91               ; relative positioning
              G1 S1 X-505 F1800 ; move quickly to X axis endstop and stop there (first pass)
              G1 X5 F6000       ; go back a few mm
              G1 S1 X-505 F360  ; move slowly to X axis endstop once more (second pass)
              G90               ; absolute positioning
              

              Home Y: homey.g

              ; homey.g
              ; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 MST (6:00PM for Civs). 
              ; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr-10s5-firmware/37
              ; Contact gost1017@gmail.com for more help.
              G91               ; relative positioning
              G1 S1 Y-505 F3000 ; move quickly to Y axis endstop and stop there (first pass)
              G1 Y5 F1000       ; go back a few mm
              G1 S1 Y-505 F360  ; move slowly to Y axis endstop once more (second pass)
              G90               ; absolute positioning
              

              Home Z: homez.g

              ; homez.g
              ; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 MST (6:00PM for Civs). 
              ; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr10s5-firmware/37
              ; Contact gost1017@gmail.com for more help.
              G91                  ; relative positioning
              G1 S1 Z-505 F10000   ; move Z down until the endstop is triggered
              G92 Z0               ; set Z position to axis minimum (you may want to adjust this)
              G1 Z3 F800           ; go back a few mm
              G1 S1 Z-505 F80      ; move slowly to X axis endstop once more (second pass)
              G90                  ; absolute positioning
              ; Uncomment the following lines to lift Z after probing
              ;G91                 ; relative positioning
              ;G1 S2 Z5 F100       ; lift Z relative to current position
              ;G90                 ; absolute positioning
              
              1 Reply Last reply Reply Quote 0
              • JamesMundefined
                JamesM
                last edited by

                Your thermistor settings are wrong for both your bed and hotend.....The bed should be M305 P0 T100000 B3950 R4700 and the volcano if it has the E3D cartridge thermistor should be M305 P1 T100000 B4725 C7.060000e-8 R4700

                1 Reply Last reply Reply Quote 1
                • Gost101undefined
                  Gost101
                  last edited by

                  Thanks, I changed that before this print: ![alt text]IMG_20190929_174503.jpg alt text

                  1 Reply Last reply Reply Quote 0
                  • Gost101undefined
                    Gost101
                    last edited by

                    I've got a lot of tweaking to do.

                    1 Reply Last reply Reply Quote 0
                    • Phaedruxundefined
                      Phaedrux Moderator
                      last edited by

                      It's not... THAT bad... I guess.

                      Z-Bot CoreXY Build | Thingiverse Profile

                      1 Reply Last reply Reply Quote 0
                      • Gost101undefined
                        Gost101
                        last edited by

                        The e3D volcano keeps getting clogged. In between the nozzle and the Capricorn tube there is a little gap that wont close and the filament expands into that and wont let me extrude. I purchased the bontech extruder to hopefully overpower the clog. Any thoughts on what to do?

                        1 Reply Last reply Reply Quote 0
                        • jay_s_ukundefined
                          jay_s_uk
                          last edited by

                          When holding the bowden tube firmly in place, fit the little clip. This should prevent the bowden tube from moving and the gap opening.
                          If you don't have a clip, fit a tie wrap to keep the bowden fitting in the heat sink in its highest position.

                          Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                          1 Reply Last reply Reply Quote 0
                          • Gost101undefined
                            Gost101
                            last edited by

                            I have a clip, however this dose not work. Confusion?????

                            1 Reply Last reply Reply Quote 0
                            • jay_s_ukundefined
                              jay_s_uk
                              last edited by

                              I had an instance where the bowden tube wasn't seating correctly in my volcano. I ended up shaving the end of the tube to give it the same angle as the bottom of the hole in the heat break so it sat further down.tube.png

                              Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                              1 Reply Last reply Reply Quote 0
                              • Gost101undefined
                                Gost101
                                last edited by

                                I was think of doing that, but have been to lazy to do anything today. Latterly been sleeping all day and playing CIV VI. I did add the bondtech extruder today, so I wasn't as lay as I wanted. I had to take the X-Axis arm off just to switch one bolt around, took about 4 hours of laziness away 😞 . I will post pictures and the new config code for the bondtech hopefully tomorrow. Then I will start the second print. May the odds ever be in my favor.

                                1 Reply Last reply Reply Quote 0
                                • Gost101undefined
                                  Gost101
                                  last edited by

                                  I will post the code later, I just purchased a new z nut as the one on the right is very hard to use. (All the weight is on the right). The right Z-Axis motor is tough to turn now, lol.IMG_20191004_213253.jpg

                                  Gost101undefined 1 Reply Last reply Reply Quote 0
                                  • Gost101undefined
                                    Gost101 @Gost101
                                    last edited by

                                    @Gost101 I'm done trying to use the volcano, I'm going to try to return it. It always clogs, I've tried tapering the Capricorn tube, it always clogs even mid print if I can get it started. I've tried putting a bontech extruder on this. I'm very frustrated and pissed off.

                                    alansrobotlabundefined 1 Reply Last reply Reply Quote 0
                                    • Gost101undefined
                                      Gost101
                                      last edited by

                                      Lol, it prints slow. I cannot increase the speed. Can anyone help?

                                      1 Reply Last reply Reply Quote 0
                                      • jens55undefined
                                        jens55
                                        last edited by

                                        Just as an additional data point: I also use a Volcano system and I have no problems now. It was frustrating to set up initially but it's working nicely now. Too much retraction was an issue with me but the one thing that stumped me for the longest time was the fact that I had the heatbreak too far out of the heatsink (Chimera setup). The necked down section of the heatbreak must be located within about 2 mm of the heatsink bottom otherwise the heat travels up too far in the heatbreak and can cause clogs where the capricorn tube meets the heat break.
                                        The Chimera setup has no threads on the heatbreak section that goes into the heatsink and with the heater and thermistor in the cramped space above the heat block, I just ended up having everything just a tad too far out of the heatsink. It was a real pain to figure this out because sometimes everything worked, sometimes it would clog on retraction, sometimes it would clog when the filament was pushed through too slow - it was a nightmare.
                                        Heat paste on the heatbreak section that is in the heatsink is also highly advisable.

                                        1 Reply Last reply Reply Quote 0
                                        • Gost101undefined
                                          Gost101
                                          last edited by

                                          In addition, I did a test print once going back to the original hotend. It was very slow and would stop after every move and leave a little blob. I cannot speed it up through the g.code files, or the web interface. I will post a video shortly of what is happening.

                                          1 Reply Last reply Reply Quote 0
                                          • Gost101undefined
                                            Gost101
                                            last edited by

                                            Here is the video link: Print Video

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA