RepRapFirmware 3.0beta 11 released

dc42

@stereo said in RepRapFirmware 3.0beta 11 released:

Do all home X, Y work fine? Am I the only one? show homex.g
On beta10

G91 ; relative positioning
G1 Z5 F6000 H2 ; lift Z relative to current position
G1 H1 X-335 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F6000 ; go back a few mm
G1 H1 X-335 F360 ; move slowly to X axis endstop once more (second pass)
G1 Z-5 F6000 H2 ; lower Z again
G90 ; absolute positioning

work good.

On beta11 goto Z5,Z-5,X5.. but does not go to the microswitch.

Please post your config.g file. Which Duet are you using?

stereo

@dc42

M574 X1 S1 P"io0.in" or
M574 X1 S0 P"io0.in"
on beta11 always triggered YES.

IF RUN "M574 Y2 S0","M574 X1 S0" work fine NO...

normal config on beta10:
M574 X1 S0 P"io0.in"

Duet3

A Former User

@dc42 FOUND THE CAUSE OF THE BUG

This is ZPROBE.IN in beta10 (bltouch disconnected)

as you can see ~3V with some ugly 50Hz garbage that should not interfere

but this is ZPROBE.IN in beta11 (bltouch disconnected)

as you can see it's floating around 1V at 50Hz so I'd say ZPROBE.IN is HIZ at this point and there is no pullup enabled... I don't see on schematic where zprobe_in becomes zprobe_mcu, are you using external pullup or you just need to configure it as in with pullup enabled .. anyhow .. there's no pullup on zprobe.in with beta11

A Former User

found the zprobe_in to zprobe_mcu .. just 10k trough and 2n2 down .. so def port configuration missing

and I also found the commit that introduced the bug:

src/Endstops/LocalZProbe.cpp:42

https://github.com/dc42/RepRapFirmware/blame/c25d73194252791ceb479ced79ffc77b31c810fe/src/Endstops/LocalZProbe.cpp#L42

you switched it from PinAccess::readWithPullup; to PinAccess::read;

A Former User

This will probbly work ok with bltouch v2 or v1 as they have 0/1 output, v3/v3.1 is open drain output so it can only pull low. Not sure why you switched from readWithPullup to read, but maybe create a new probe type with pullup, or should we add external pullup if this is to remain without one on the port?

Nuramori

@smece sadly, I saw your posts 3 minutes too late :p.

Thought my errant height map was a fluke due to a part swap. I dug a nice groove into my test spring plate (luckily I always use a sacrificial test plate whenever I change anything on the printer, hardware or software).

Moving back to 10 brought everything back to “normal”.

dc42

@smece said in RepRapFirmware 3.0beta 11 released:

so I'd say ZPROBE.IN is HIZ at this point and there is no pullup enabled... I don't see on schematic where zprobe_in becomes zprobe_mcu, are you using external pullup or you just need to configure it as in with pullup enabled .. anyhow .. there's no pullup on zprobe.in with beta11

Thanks for tracking this down. I removed implicit enabling of pullup resistors in beta 11 because it meant that you couldn't turn them off. If you want to enable the pullup resistor, you need to be explicit by using C"^zprobe.in" in your M558 command.

The BLTouch that I test with is the older version that drives the output high when triggered, that's why I didn't see the problem during testing.

I'll update the documentation to make this clear.

A Former User

@dc42 said in RepRapFirmware 3.0beta 11 released:

you need to be explicit by using C"^zprobe.in" in your M558 command.

Perfect, this solves the problem. Everything works ok now.

M558 P9 C"^zprobe.in" H5 F120 T3000 A2
M950 S0 C"exp.heater3"
G31 P100 X35 Y0 Z2.2

fma

I just installed RRF3.0beta11 on my DuetWifi2, and I have troubles configuring Fans. In my config.g file, I have:

M950 F0 C"heater1" Q100    ; Fan 0 (water pump) is connected to heater 1, PWM at 100Hz
M950 F1 C"heater2" Q100    ; Fan 1 (Berd air pump) is connected to heater 2, PWM at 100Hz
M950 F2 C"duex.fan3" Q100  ; Fan 2 (Leds) is connected to heater 2, PWM at 100Hz
M950 S0 C"fan0"            ; Servo 0 is connected to "fan0" pin

; Tools
M563 P0 D0 H1 F1 S"Manual"  ; Define tool 0 using Drive 0, Heater 1 and Fan 1

But I don't see any fan controls in DWC2... What I missed?

I also would like to know:

how to setup thermostatic control for a fan
how to name a fan

Thanks,

PS: the tool is working fine.

gtj0

@fma You still need M106 commands...

This is for a Duet3 but

; Fans & LEDs
M950 F0 C"out7" Q25000
M106 P0 C"PartCooling" S0  H-1
M950 F1 C"out8" Q25000
M106 P1 C"HotEnd" T45 H1

M950 F2 C"out9" Q100
M106 P2 S255 B0 C"Bed LED"

fma

Ok, I see. Thanks!

fma

I also have the homing issue G0/G1: insufficient axes homed.

But it does not happen all the time. It can home fine, then it does not. I can't find a pattern, it can happens at different stages...

I'm using a Duet2Wifi.

Here are my congif.g and all homing files:

; Configuration file for Duet WiFi
; executed by the firmware on start-up

; General preferences
M111 S0  ; Debugging off
G21      ; Work in millimetres
G90      ; Send absolute coordinates...
M83      ; ...but relative extruder moves
M555 P2  ; Set firmware compatibility to look like Marlin
M667 S1  ; Select CoreXY mode

; Drives
M208 X-60:302 Y-100:305 Z0:320 U-1000:1000  ; Set axis limits
M584 X0 Y1 Z2 E5 U6                         ; Remap axes
M569 P0 S1                                  ; Drive 0 goes forwards
M569 P1 S1                                  ; Drive 1 goes forwards
M569 P2 S0                                  ; Drive 2 goes reverse
M569 P5 S0                                  ; Drive 5 goes reverse
M569 P6 S1                                  ; Drive 6 goes forward
M350 X16 Y16 Z16 E16 U16 I1                 ; Configure microstepping with interpolation
M92 X66.667 Y66.667 Z1417.323 E530 U140     ; Set steps per mm
M203 X30000 Y30000 Z1200 E3600 U3600        ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z100 E3000 U3000           ; Set accelerations (mm/s^2)
M566 X900 Y900 Z60 E600 U600                ; Set maximum instantaneous speed changes (mm/min)
M906 X1750 Y1750 Z1750 E750 U1250 I30       ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                     ; Set motors idle timeout

; Endstops (must be defined after any M584 command)
M574 X2 S1 P"xstop"  ; X min active high endstop switch
M574 Y2 S1 P"ystop"  ; Y min active high endstop switch
M574 Z1 S1 P"zstop"  ; Z min active high endstop switch

; Sensors
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700               ; bed temperature sensor uses 'bedtemp' pin
M308 S1 P"duex.e2temp" Y"thermistor" T100000 B4725 C7.06e-8 R4700  ; E0 temperature sensor uses 'deux.e2temp' pin

; Heaters
M950 H0 C"bedheat" T0          ; heater 0 uses the 'bedheat' pin and sensor 0
M143 H0 S120                   ; Set maximum heater 0 temperature to 120°C (not yet supported)
M307 H0 A105.6 C627.9 D1.5 B0  ; Auto-tune values for heater 0
M950 H1 C"duex.e2heat" T1      ; heater 1 uses the 'duex.e2heat' pin and sensor 1
M143 H1 S280                   ; Set maximum heater 1 temperature to 280C (not yet supported)

; Fans
M950 F0 C"e0heat" Q100000           ; Fan 0 connected to 'e0heat' pin, PWM at 100KHz
M106 P0 C"Part cooling"             ; Part cooling fan uses fan 0
M950 F1 C"e1heat" Q100000           ; Fan 1 connected to 'e1heat' pin, PWM at 100KHz
M106 P1 C"Water pump" T45 H1 X0.25  ; Thermostatic fan uses fan 1, monitor heater 1, max PWM 25% (6V out of 24V)
M950 F2 C"duex.fan3" Q100           ; Fan 2 connected to 'duex.fan3' pin, PWM at 100Hz
M106 P2 C"Leds"                     ; Leds uses fan 2

; Servos
M950 S0 C"fan0"  ; Servo 0 connected to 'fan0' pin

; Tools
M563 P0 D0 H1 F1 S"Manual"  ; Define tool 0 using Drive 0, Heater 1 and Fan 1
G10 P0 X0 Y0 Z0             ; Set tool 0 axis offsets
G10 P0 R190 S190            ; Set initial tool 0 active and standby temperatures
M207 S1.5 F2400             ; Set retraction length (G10/G11)
M572 D0 S0.08               ; Pressure advance

; Network
M550 PDuetWifi  ; Set machine name
M551 Pxxxxxx    ; Set password
M552 S1         ; Enable network
; Access point is configured manually via M587 by the user
M586 P0 S1      ; Enable HTTP
M586 P1 S1      ; Enable FTP
M586 P2 S0      ; Disable Telnet

; Misc
M912 P0 S-13  ; Calibrate CPU temp.
M106 P2 S0.1  ; Turn leds on 10%

; Custom settings are not configured

; homeall.g
; called to home all axes

M98 P0:/sys/homexy.g
M98 P0:/sys/homez.g
M98 P0:/sys/homeu.g

; homexy.g
; called to home the X and Y axis

G91  ; relative positioning

G1 Z1 F1200 H2  ; lift Z

G1 X325 Y325 F1800 H1  ; course home X or Y
G1 X325 H1             ; course home X
G1 Y325 H1             ; course home Y
G1 X-5 Y-5 F6000       ; move away from the endstops
G1 X325 F300 H1        ; fine home X
G1 Y325 H1             ; fine home Y

G1 Z-1 F1200 H2  ; lower Z

G90  ; absolute positioning

; homez.g
; called to home the Z axis

G91  ; relative positioning

G1 Z-325 F600 H1  ; course home Z
G1 Z5 F1200       ; move away from the endstop
G1 Z-325 F120 H1  ; Fine home Z

G90  ; absolute positioning

; homeu.g
; called to home the U axis

G92 U0

Thanks for you help.

deckingman

@fma You need to put your M584 before M667 and M208. Look at the order dependencies here https://duet3d.dozuki.com/Wiki/Gcode#Section_M584_Set_drive_mapping. Also, it probably won't make any difference but M667 is deprecated and you should really be using M669 instead of M667.

fma

Ok, thanks. I applied all these corrections, but I still have the issue.

I tried to removed the U axis: not better.

deckingman

@fma Then I guess what's needed is some way of reproducing the problem - it's always difficult to diagnose when there is an element of "randomness" involved.

Unfortunately, I'm unable to help much more because I can't home my printer at all. Some of my end stops are on expansion boards and RRF 3 firmware doesn't yet work for homing with end stops on expansion boards.

JoergS5

@fma said in RepRapFirmware 3.0beta 11 released:

M208 X-60:302 Y-100:305 Z0:320 U-1000:1000

I would propose as reason:
M208 X-60:302 Y-100:305 Z0:320 U-1000:1000
means X maximum distance is 362, Y is 405, but you home only 325 each in
G1 X325 Y325 F1800 H1
, so depending on your current position you reach one of the endstops or not, assumed, 0 position is not defined after turning the printer on. I would change to
G1 X500 Y500 F1800 H1
and the followong two also to be sure they reach the endstops..

JoergS5

This post is deleted!

JoergS5

If G1 X325 Y325 F1800 H1 reaches X immediately, M208 defines X/Y position as 302/305, but in reality Y may be at -100. So it will not reach the endstop with the following Y move, even when the first line reached an endstop. So better 500 for the following two lines also.

fma

The min values are wrong; I didn't noticed it because I home on max values. Anyway, total travel for X and Y is < 325mm, so the endstops are always reached (I'm using relative positionning). And in my tests, I'm close to the max positions, so carriage travels only a few mm before hitting the endstops.

And it was working fine with 2.02/2.03 firmwares; I just changed the S param to H param in the G1 moves.

fma

I confirm it is totally random.

Say I'm on the max position, both endstops X/Y activated. If I hit the homing button several times, I can see the machine homing X then fail, or Y, the fail, or none, or successfully home all axis.

But I find a workaround: I changed

G1 X-5 Y-5 F6000       ; move away from the endstops

to

G1 X-5 Y-5 F6000 H2    ; move away from the endstops

and it now works fine. If it can helps to find the problem...