Stall Guard

Phaedrux · 24 Feb 2020, 00:31

I'm guess H0 isinvalid and it's using the default instead. Try H50? Possibly the same with F0? I don't have the wiki open on my phone ATM.

I don't think there is anything wrong with sending it whenever you want. Nothing really needs to be in config.g.

BlueDust · 24 Feb 2020, 00:49

@Phaedrux
I am just more confused now...
I have tried H50 already. I just went to the extreme with 0. I already use F0 for sensorless homing. It should just make it more sensitive at sharp movements and F1 should be used during normal printing.
I am just trying to get it to work during a print and just trip once so I have some proof this feature works. It currently doesn't make any sense to me why it works for homing and I can't get it to work during a print. I must have some other setting enabled/disabled that is affecting it.

Phaedrux · 24 Feb 2020, 00:54

Is this on I duet wifi? Or maestro?

BlueDust · 24 Feb 2020, 00:54

@Phaedrux

Duet2 Ethernet

Phaedrux · 24 Feb 2020, 01:01

12v or 24v?

BlueDust · 24 Feb 2020, 01:04

@Phaedrux
24v

BlueDust · 24 Feb 2020, 01:56

I don't know if this is actually relevant, but I also read that this Stall Guard may need some fine tuning pointing to this formula sheet.
I filled it out best to my understanding, but do not know how to use it.

Phaedrux · 24 Feb 2020, 02:58

Do you have a link to that sheet?

Phaedrux · 24 Feb 2020, 03:03

Have you tried getting it to detect a stall on a pure diagonal move to isolate just a single motor?

BlueDust · 25 Feb 2020, 13:36

@Phaedrux
There is a link on the Sensorless homing wiki page that takes you to another page to talk about motors. This site has a link to download the calculation sheet I shared the screen shot of.

https://duet3d.dozuki.com/Wiki/Choosing_and_connecting_stepper_motors

BlueDust · 25 Feb 2020, 13:38

@Phaedrux
I just printed a large print with long movements and held the belts still.

I can try printing a large calibration cube and see what happens.
Thanks.

dc42 · 26 Feb 2020, 09:59

@BlueDust said in Stall Guard:

M915 X Y S-10 F0 H200 R3

With S-10 I would expect the motor to register stalled nearly all the time. You can check by sending M122 during a print and looking at the driver status.

On my delta I have M915 set to warn about motor stalls. Using the same M915 settings as when I test sensorless homing on that machine, I get occasional (false) warnings. So I know that it is working at least some of the time.

BlueDust · 28 Feb 2020, 12:29

@dc42
I have been having a lot of trouble with the nozzle getting stuck in the print, and breaking different Z probes and why I want to fix this feature. I am having a lot of Z probe issues again caused by the crashes and not able to bed level. I will run m122 after I can print again.
Thanks

dc42 · 28 Feb 2020, 15:55

I have this on my list to look at, but I need to get firmware 3.01-RC3 released first. Please remind me again on Monday, assuming 3.01-RC3 is released by then.

BlueDust · 3 Mar 2020, 01:29

@dc42 said in Stall Guard:

M122

As I do use stall guard for homing, I wanted to compare both before and after I enabled it for printing...

This is before I enabled stall guard (printing)

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05 running on Duet Ethernet 1.02 or later + DueX5
Board ID: 08DGM-9T6BU-FG3S0-7JTDL-3SN6N-TS6VG
Used output buffers: 3 of 24 (24 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93836 of which 0 recycled
Exception stack ram used: 656
Never used ram: 10868
Tasks: NETWORK(ready,628) HEAT(blocked,1232) DUEX(suspended,160) MAIN(running,1300) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 70:56:51 ago, cause: software
Last software reset at 2020-02-28 21:23, reason: User, spinning module GCodes, available RAM 11240 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: c
Free file entries: 8
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 17.0ms, max retries 1
MCU temperature: min 33.7, current 36.2, max 39.4
Supply voltage: min 23.5, current 23.8, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/201
Driver 1: ok, SG min/max 0/205
Driver 2: standstill, SG min/max not available
Driver 3: ok, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max 0/1023
Driver 8: standstill, SG min/max 0/1023
Driver 9: standstill, SG min/max 0/1023
Date/time: 2020-03-02 20:20:51
Cache data hit count 4294967295
Slowest loop: 261.76ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 157, MinFreeDm: 132, MaxWait: 21532997ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 189, completed moves: 165, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.2
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 1
Stack records: 3 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X170.351 Y213.116 E12.2842" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 372.96ms; fastest: 0.05ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
Interface state 5, link 100Mbps full duplex
=== Filament sensors ===
Extruder 0: pos 280.55, errs: frame 164 parity 0 ovrun 0 pol 5 ovdue 0

This is just what I had used to enable it this time...

M915 X Y S3 F1 H100 R3

Same print as above Diagnostic text. I just ran the M915 command mentioned above, printer rehomed itself, and I copied the M122 Diagnostic text.

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05 running on Duet Ethernet 1.02 or later + DueX5
Board ID: 08DGM-9T6BU-FG3S0-7JTDL-3SN6N-TS6VG
Used output buffers: 1 of 24 (24 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93836 of which 0 recycled
Exception stack ram used: 656
Never used ram: 10868
Tasks: NETWORK(ready,628) HEAT(blocked,1232) DUEX(suspended,160) MAIN(running,1300) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 71:04:28 ago, cause: software
Last software reset at 2020-02-28 21:23, reason: User, spinning module GCodes, available RAM 11240 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: c
Free file entries: 8
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 38.3, current 38.9, max 39.2
Supply voltage: min 23.7, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 79/192
Driver 1: ok, SG min/max 80/184
Driver 2: standstill, SG min/max not available
Driver 3: ok, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Date/time: 2020-03-02 20:28:27
Cache data hit count 4294967295
Slowest loop: 3.33ms; fastest: 0.09ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 142, MinFreeDm: 128, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 4941, completed moves: 4905, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.2
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 1
Stack records: 3 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X208.678 Y124.970 E0.4618" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 6.89ms; fastest: 0.05ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
Interface state 5, link 100Mbps full duplex
=== Filament sensors ===
Extruder 0: pos 280.20, errs: frame 164 parity 0 ovrun 0 pol 5 ovdue 0

BlueDust · 13 Mar 2020, 01:51

@dc42
I know I am a little late with this... Reminder.
As always, Thank you for your help!

dc42 · 13 Mar 2020, 12:50

@BlueDust, have you tried RRF3 yet? That's where development is now focused.

BlueDust · 14 Mar 2020, 06:03

@dc42
No. I wanted to wait until there was an official release and not just an RC. Also after I got this working... That way I didn't have to troubleshoot with new code.
I may have the time to work on the conversation to RRF3 next weekend... I will follow up again after I upgrade the software and try this again.

Thanks.