Duet Web Control 2.1.1 released

chrishamm

Thanks, I've already fixed the crash that occurs when a heater fault occurs and I'll fix the filament assignment next. Both fixes will be available when RRF 3.01 is released. Likewise the "Turn off all" button has been fixed and a new DWC version will be released among the next DSF version.

SIam

@smoki3

M122 is working here

6.4.2020, 20:32:50 	m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.01-RC6 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-95BNL-MGPSJ-6J9FD-3SJ6N-K1W3Y
Used output buffers: 4 of 24 (22 max)
=== RTOS ===
Static ram: 28052
Dynamic ram: 94208 of which 24 recycled
Exception stack ram used: 576
Never used ram: 8212
Tasks: NETWORK(ready,116) HEAT(blocked,1244) DUEX(suspended,136) MAIN(running,1608) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 11:14:43 ago, cause: software
Last software reset at 2020-04-06 09:18, reason: User, spinning module GCodes, available RAM 8532 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 133.8ms, max retries 0
MCU temperature: min 21.7, current 39.7, max 41.7
Supply voltage: min 24.0, current 24.3, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/981
Driver 1: standstill, SG min/max 0/1023
Driver 2: standstill, SG min/max 0/1023
Driver 3: standstill, SG min/max 0/1023
Driver 4: standstill, SG min/max 0/1023
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max 0/1023
Date/time: 2020-04-06 20:32:48
Cache data hit count 4294967295
Slowest loop: 312.35ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 107, MaxWait: 5922743ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.7
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 789.12ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(2) FTP(0) Telnet(0)
HTTP sessions: 2 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 2c:3a:e8:0b:06:33
WiFi Vcc 3.44, reset reason Unknown
WiFi flash size 4194304, free heap 15424
WiFi IP address 192.168.188.36
WiFi signal strength -49dBm, reconnections 0, sleep mode modem
Socket states: 4 0 0 4 0 0 0 0
=== Filament sensors ===
Extruder 0 sensor: ok

GrodanB

@chrishamm said in Duet Web Control 2.1.1 released:

Great, by the way, great work. Much appreciated.

Do you require me to upgrade to RRF 3.01? Do not see the benefit to me until new functions are added at the moment I understand that soon it will be at the same function level as latest 2.x.

Again thanks.

DocTrucker

@GrodanB said in Duet Web Control 2.1.1 released:

Do you require me to upgrade to RRF 3.01?

@jay_s_uk said in Duet Web Control 2.1.1 released:

Its dependant on RRF3.01+ as it uses the object model

smoki3

@SIam said in Duet Web Control 2.1.1 released:

@smoki3

M122 is working here

6.4.2020, 20:32:50 	m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.01-RC6 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-95BNL-MGPSJ-6J9FD-3SJ6N-K1W3Y
Used output buffers: 4 of 24 (22 max)
=== RTOS ===
Static ram: 28052
Dynamic ram: 94208 of which 24 recycled
Exception stack ram used: 576
Never used ram: 8212
Tasks: NETWORK(ready,116) HEAT(blocked,1244) DUEX(suspended,136) MAIN(running,1608) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 11:14:43 ago, cause: software
Last software reset at 2020-04-06 09:18, reason: User, spinning module GCodes, available RAM 8532 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 133.8ms, max retries 0
MCU temperature: min 21.7, current 39.7, max 41.7
Supply voltage: min 24.0, current 24.3, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/981
Driver 1: standstill, SG min/max 0/1023
Driver 2: standstill, SG min/max 0/1023
Driver 3: standstill, SG min/max 0/1023
Driver 4: standstill, SG min/max 0/1023
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max 0/1023
Date/time: 2020-04-06 20:32:48
Cache data hit count 4294967295
Slowest loop: 312.35ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 107, MaxWait: 5922743ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.7
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 789.12ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(2) FTP(0) Telnet(0)
HTTP sessions: 2 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 2c:3a:e8:0b:06:33
WiFi Vcc 3.44, reset reason Unknown
WiFi flash size 4194304, free heap 15424
WiFi IP address 192.168.188.36
WiFi signal strength -49dBm, reconnections 0, sleep mode modem
Socket states: 4 0 0 4 0 0 0 0
=== Filament sensors ===
Extruder 0 sensor: ok

I just get this without an output. Are you on Duet 2 Wifi?

Bildschirmfoto 2020-04-07 um 09.37.23.png

jay_s_uk

@smoki3

i get full M122 output on a duet 3 + pi and a duet 2 ethernet

wilriker

@jay_s_uk @DocTrucker @GrodanB DWC 2.1.1 is supposed to work with RRF versions pre-ObjectModel. Unfortunately, currently there is a bug in the code that prevents it to get into legacy-mode.

SIam

@smoki3
Yes i use duet wifi

jay_s_uk

@wilriker good to know!

chrishamm

@wilriker I am not aware of this bug, in fact I successfully tested DWC 2.1 with RRF2 just a few days ago.

wilriker

@chrishamm @jay_s_uk It seems that this bug is only for very specific uncommon configurations. So it should already work with everything <3.01-something

c310

How to enable fans on GUI ?!

chrishamm

@c310 Job Status => Fans => Change Visibility

GrodanB

@wilriker said in Duet Web Control 2.1.1 released:

@jay_s_uk @DocTrucker @GrodanB DWC 2.1.1 is supposed to work with RRF versions pre-ObjectModel. Unfortunately, currently there is a bug in the code that prevents it to get into legacy-mode.

OK... so next release might contain the fix so that it is 2.x compatible?

Plan to go to 3.x but not convinced that it is as good as 2.x yet... Seems to have some bug left to remove until I feel it is worth the work... (2.x works fine for me and I only upgrade for any new features so far...)

But being able to use new DWC is a good reason for upgrade if that is necessary...

c310

@chrishamm it does not show up at all. however, if i switch to DWC1 fan is there and works...

888577df-9bc9-4b72-8db6-386786ade95e-изображение.png

chrishamm

@c310 What firmware are you using? Is the fan thermostatically controlled? If yes, no fans are displayed.

c310

@chrishamm it was 3.01RC4 with invisible symptoms ... after i upgraded to RC6 it is visible now.
why thermostatic fans are invisible?
how i can input into localization / correct some minor mistakes ?

droftarts

@c310 said in Duet Web Control 2.1.1 released:

why thermostatic fans are invisible?

Because if they're under temperature control, you can't change their speed, so there's no point having a control over them that doesn't work. If send the gcode to make them non-thermostatic, they will appear. Also (not sure exactly if it's true with the current version), fans linked to specific tools usually don't show until that tool is enabled.

Ian

smoki3

@smoki3 said in Duet Web Control 2.1.1 released:

@SIam said in Duet Web Control 2.1.1 released:

@smoki3

M122 is working here

6.4.2020, 20:32:50 	m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.01-RC6 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-95BNL-MGPSJ-6J9FD-3SJ6N-K1W3Y
Used output buffers: 4 of 24 (22 max)
=== RTOS ===
Static ram: 28052
Dynamic ram: 94208 of which 24 recycled
Exception stack ram used: 576
Never used ram: 8212
Tasks: NETWORK(ready,116) HEAT(blocked,1244) DUEX(suspended,136) MAIN(running,1608) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 11:14:43 ago, cause: software
Last software reset at 2020-04-06 09:18, reason: User, spinning module GCodes, available RAM 8532 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 133.8ms, max retries 0
MCU temperature: min 21.7, current 39.7, max 41.7
Supply voltage: min 24.0, current 24.3, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/981
Driver 1: standstill, SG min/max 0/1023
Driver 2: standstill, SG min/max 0/1023
Driver 3: standstill, SG min/max 0/1023
Driver 4: standstill, SG min/max 0/1023
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max 0/1023
Date/time: 2020-04-06 20:32:48
Cache data hit count 4294967295
Slowest loop: 312.35ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 107, MaxWait: 5922743ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.7
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 789.12ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(2) FTP(0) Telnet(0)
HTTP sessions: 2 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 2c:3a:e8:0b:06:33
WiFi Vcc 3.44, reset reason Unknown
WiFi flash size 4194304, free heap 15424
WiFi IP address 192.168.188.36
WiFi signal strength -49dBm, reconnections 0, sleep mode modem
Socket states: 4 0 0 4 0 0 0 0
=== Filament sensors ===
Extruder 0 sensor: ok

I just get this without an output. Are you on Duet 2 Wifi?

Bildschirmfoto 2020-04-07 um 09.37.23.png

@chrishamm can you help here? Looks like for some it is working. I already tried a reset of DWC but it is not working.

Danal

When trying to load heightmap, getting:

HeightmapPanel.vue:415 TypeError: Cannot read property 'add' of null
    at o.showHeightmap (HeightmapPanel.vue:313)
    at o.showCSV (HeightmapPanel.vue:258)
    at HeightmapPanel.vue:413
    at c (runtime.js:45)
    at Generator._invoke (runtime.js:274)
    at Generator.forEach.e.<computed> [as next] (runtime.js:97)
    at Dt (asyncToGenerator.js:3)
    at o (asyncToGenerator.js:25)
(anonymous) @ HeightmapPanel.vue:415
c @ runtime.js:45
(anonymous) @ runtime.js:274
forEach.e.<computed> @ runtime.js:97
Dt @ asyncToGenerator.js:3
o @ asyncToGenerator.js:25
Promise.then (async)
Dt @ asyncToGenerator.js:13
o @ asyncToGenerator.js:25
(anonymous) @ asyncToGenerator.js:32
(anonymous) @ asyncToGenerator.js:21
getHeightmap @ HeightmapPanel.vue:396
isConnected @ HeightmapPanel.vue:479
ni.run @ vue.runtime.esm.js:4568
Zn @ vue.runtime.esm.js:4310
(anonymous) @ vue.runtime.esm.js:1980
ct @ vue.runtime.esm.js:1906
Promise.then (async)
at @ vue.runtime.esm.js:1933
pt @ vue.runtime.esm.js:1990
b @ vuex.esm.js:602
v.registerModule @ vuex.esm.js:498
addMachine @ index.js:157
(anonymous) @ vuex.esm.js:744
(anonymous) @ vuex.esm.js:392
(anonymous) @ vuex.esm.js:391
v._withCommit @ vuex.esm.js:526
v.commit @ vuex.esm.js:390
commit @ vuex.esm.js:335
(anonymous) @ index.js:58
c @ runtime.js:45
(anonymous) @ runtime.js:274
forEach.e.<computed> @ runtime.js:97
Dt @ asyncToGenerator.js:3
o @ asyncToGenerator.js:25
Promise.then (async)
Dt @ asyncToGenerator.js:13
o @ asyncToGenerator.js:25
(anonymous) @ asyncToGenerator.js:32
(anonymous) @ asyncToGenerator.js:21
connect @ index.js:43
(anonymous) @ vuex.esm.js:751
v.dispatch @ vuex.esm.js:442
dispatch @ vuex.esm.js:332
F.forEach.n.<computed> @ vuex.esm.js:964
mounted @ App.vue:212
nt @ vue.runtime.esm.js:1854
Nn @ vue.runtime.esm.js:4219
insert @ vue.runtime.esm.js:3139
E @ vue.runtime.esm.js:6346
(anonymous) @ vue.runtime.esm.js:6565
On.e._update @ vue.runtime.esm.js:3945
i @ vue.runtime.esm.js:4066
ni.get @ vue.runtime.esm.js:4479
ni @ vue.runtime.esm.js:4468
In @ vue.runtime.esm.js:4073
Mi.$mount @ vue.runtime.esm.js:8415
e._init @ vue.runtime.esm.js:5018
Mi @ vue.runtime.esm.js:5085
56d7 @ main.js:20
n @ bootstrap:19
0 @ app.f1b8ca4b.js:1
n @ bootstrap:19
(anonymous) @ bootstrap:83
(anonymous) @ app.f1b8ca4b.js:1
three.module.js:15728 Uncaught TypeError: Cannot read property 'precision' of null
    at a (three.module.js:15728)
    at new bM (three.module.js:15760)
    at se (three.module.js:23461)
    at new kk (three.module.js:23510)
    at o.init (HeightmapPanel.vue:185)

RepRapFirmware height map file v2 generated at 2020-04-08 00:35, min error -0.099, max error 0.095, mean 0.002, deviation 0.046
xmin,xmax,ymin,ymax,radius,xspacing,yspacing,xnum,ynum
-225.00,225.10,-225.00,225.10,300.00,75.00,75.00,7,7
      0,  0.055, -0.039, -0.019, -0.006,  0.010,      0
  0.046,  0.095,  0.006,  0.000, -0.011, -0.062,  0.018
  0.086,  0.055,  0.020, -0.010, -0.041, -0.001, -0.045
  0.077,  0.020,  0.054, -0.019, -0.079, -0.051,  0.001
  0.070,  0.056,  0.020, -0.000, -0.055, -0.015, -0.099
 -0.002,  0.070,  0.068,  0.021, -0.020, -0.065, -0.075
      0,  0.002, -0.007, -0.002, -0.024, -0.006,      0