Wifi module idle

show us M587 with no parameters?

tkdirp

@bearer
What does it mean to have an M587 with no parameters? I just don't know because I am pretty new to this.

Dougal1957

@tkdirp said in Wifi module idle:

@bearer
What does it mean to have an M587 with no parameters? I just don't know because I am pretty new to this.

just send M587 on its own with nothing after it then the Duet will tell us what it has set!

just send M587 (with no S"......" P".....")

it should return the stored netwoks in the wifi module.

tkdirp

@bearer @Dougal1957
SSID: U+Net48C4
PW: 8040P8C0#1

what firmware are you running?

check with M122. The Duet board firmware will be at the top, and the Wifi firmware will be in a a section at the bottom.

tkdirp

@bearer
seem to be 2.03
Screen Shot 2020-07-04 at 4.23.59 PM.png

@tkdirp said in Wifi module idle:

2.03

thats just the RepRapFirmware version, as I said when you run M122 it will also print the version of the firmware running om the Wifi module.

tkdirp

@bearer
This happens if I send a M122 command...
Screen Shot 2020-07-04 at 7.45.15 PM.png

right, wifi not happy.

btw could you try running stty -F /dev/tty.usbmodem14101 inlcr in another terminal and see if it sorts the line endings for you? (edit or stty -F /dev/tty.usbmodem14101 -icrnl)

then lets try the nuke from orbit approach.

M552 S-1
M552 S0
M588 S"*"
M587 S"U'+Net48C4" p"8040P8C0#1" 
M552 S1

M552 S-1 resets the wifi module
M588 S"*" clears the wifi credentials

edit fixed typo ~~M589~~ to M588

tkdirp

@bearer said in Wifi module idle:

in another terminal

So, on another computer?

@tkdirp said in Wifi module idle:

another computer?

no, same computer just another window with a terminal. (but its not that important, it just makes it easier to read if the end of line characters actually causes a new line - and I'm not sure if it would work on a Mac)

tkdirp

@bearer said in Wifi module idle:

M552 S-1 resets the wifi module
M589 S"*" clears the wifi credentials

The nuke plan failed...
Screen Shot 2020-07-04 at 8.26.26 PM.png

but M122 shows the wifi version now?

if not lets try

M552 S-1
M552 S0
M588 S"*"
M122

edit: fixed typo ~~M589~~ to M588

tkdirp

@bearer
M122 is still not working

tkdirp

@bearer said in Wifi module idle:

M552 S-1
M552 S0
M589 S"*"
M122

Worked.
Screen Shot 2020-07-04 at 8.46.44 PM.png

ah, okay, was about to suggest just updating it without finding out which version it is, but thats all up to date then. (1.23 is the latest iirc)

if you run M111 P14 S1 it will enable debug output for wifi.

then run M587 S... P.... (with your credentials) followed by M552 S1

(but I suspect you really need to find another terminal for that to be usefull, or have screen translate LF into CR/LF)

((edit: if you must use screen maybe log to a file and view the file (in another window) with fixed line endings tail -F my.log | sed 's/$/\r/' ))

tkdirp

@bearer said in Wifi module idle:

M111 P14 S1

After that commend, the M587 S"U'+Net48C4" P”8040P8C0#1" dos not seem to have any significant effect
Screen Shot 2020-07-04 at 9.05.45 PM.png

@tkdirp said in Wifi module idle:

dos not seem to have any significant effect

thats okay, was primarily after the ouput that say WiFi: ../src/Sock <...> found network U+Net48C4.

Either the + is a problem or there is some sort of interoperability issue with the router.

I would suggest checking the encyption type, or change it to WPA(2)/TKIP, changing the SSID and Passphrase to something without special charters.

Or optionally use M589 to set up the duet as an access point.

But first, repeat https://forum.duet3d.com/post/164593 as I had made a typo in the command to clear the wifi settings. (However as you did get an OK at some point i doubt it'll make a difference)

forgot the link to M589 to try AP mode
https://duet3d.dozuki.com/Wiki/Gcode#Section_M589_Configure_access_point_parameters