Homing advice

Phaedrux

Did you copy and paste my homing files into yours?

And just to confirm...
Is the X endstop on the left or right?
Is the Y endstop at the front or back?

agent0810

yes sir, copied and pasted.

The Y is in the back right corner.
The x is on the right,

Phaedrux

M574 X2 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y2 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop

And you changed M574 to X2 and Y2?

agent0810

yes sir copied all 3 homing files and pasted over mine.

; Endstops
M574 X2 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop

Phaedrux

Alright, then we may need to change a motor direction.

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards

Try

M569 P0 S0
M569 P1 S0

agent0810

That may have done it.

X+ Moves to the right !!!!!!
Y+ Moves to the Back!!!!
Z+ Moves up!!!!!

so after i home, the "position tool" says its X - 225.0, Y 225.0, Z - 300.00 thats what i want right?

Phaedrux

@agent0810 said in Homing advice:

X - 225.0, Y 225.0, Z - 300.00

Are those negative values?

agent0810

no dashes,

Status
Printing
Mode: FFF
Tool Position
X
225.0
Y
225.0
Z
300.00

Phaedrux

The last thing to check is that when you move to 0,0 it's at the corner of the bed. If it's not, then you'll have to adjust the M208 maxima values.

agent0810

so when i "home all" it sends it to the back right corner. when i got to 0,0 it goes to the front left corner. when i try to start a print, it starts in the back right corner, bangs against the stops then the bed starts to lower all the way.

Phaedrux

What do you have in your start gcode?

agent0810

Here is the start:

;FLAVOR:Marlin
;TIME:336
;Filament used: 0.10025m
;Layer height: 0.2
;MINX:89
;MINY:95
;MINZ:0.2
;MAXX:131
;MAXY:125
;MAXZ:14.8
;Generated with Cura_SteamEngine 4.6.1
M140 S60
M105
M190 S60
M104 S230
M105
M109 S230
M82 ;absolute extrusion mode
M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk
M220 S100 ;Reset Feedrate
M221 S100 ;Reset Flowrate

G28 ;Home

G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up
G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up

G92 E0
G92 E0
G1 F5100 E-7
;LAYER_COUNT:86
;LAYER:0
M107

Phaedrux

@agent0810 said in Homing advice:

M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk

Unrelated, but delete those lines from your slicer start gcode section in Cura.

I don't see a G90 in there to make sure you're in absolute positioning mode.

Does it do the prime line correctly or does it just start crashing?

agent0810

just starts crashing.

agent0810

Here are my machine settings in cura......do the print head settings look okay?

Phaedrux

Change the Gcode flavor to RepRap.

Can you share an actual sliced gcode file?

agent0810

yea let me see what i can get. should i just place G90 in before the G92? googled it and didnt see an actual setting for it in cura but someone said they just put it in the start code.

Phaedrux

Well I'd like to see the full sliced gcode first to see what it's actually got inserted where.

agent0810

I think this is what you are looking for.

base_x.gcode

Phaedrux

Ok, try changing your start gcode to be

M220 S100 ;Reset Feedrate
M221 S100 ;Reset Flowrate

G28 ;Home
G90 ; absolute positioning.

G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up
G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up

G92 E0
G92 E0
G1 F5100 E-7

The other question I have is about your Z probe. Currently you are homing to the Z max position with an endstop. Do you also have a probe installed? Is your Z axis moving correctly?