Bltouch setup need help
-
Swapped
M558 and M950
hotend goes to middle of the bed and deploys probe then probe swiches off I thinkcheers for the help guys
-
@Elvis0z you should check G31 Z value also, please see my last post above.
In homeall I would move the hotend to the middle of the bed before probing Z, instead G1 X15 Y15 F6000 I would call
G1 X100 Y100 F6000
to be sure you don't probe outside of the bed one day and not triggering (when bed or endstop moved a bit eg). -
This was the last error
G28
Error: Z probe was not triggered during probing move
Error: Homing failed -
@Elvis0z was your bltouch over the bed and was it deployed?
-
@JoergS5 Yes
-
M401
M402
Both these commands work -
@Elvis0z did it have a bit of distance to the bed? There are some documentation to the installation. The Z height in reference to the nozzle is important.
The image right lower on page 1 in the https://locxess.de/3d/BLTouch_Anleitung_englisch.pdf
document, the 8mm. -
Yep it probes way above the bed.
-
@Elvis0z can you please republish config and homeall like it is now, so I can recheck?
-
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Tue Jun 09 2020 17:58:51 GMT-0700 (Mountain Standard Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Elvis Oz Tevo Black Widow" ; set printer name; Network
;M551 P"" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; enable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z1600.00 E400.00 ; set steps per mm
M566 X500.00 Y500.00 Z18.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z100.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z1200 E1300 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X360 Y230 Z280 S0 ; set axis maxima; Endstops
M574 X1 S1 P"!xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z; Elvis, The following Z-Probe below is where you will have to configure your BLTouch
; Z-Probe
M558 P9 C"^zprobe.in" H5 F60 T6000 A10 R0.5
M950 S0 C"exp.heater3"
G31 P25 X+41 Y+10 Z0.0 ; set Z probe trigger value, offset and trigger height
M557 X25:360 Y15:220 S20 ; define mesh bed level; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 A346.2 C140 D5.3 B0 S2.0 V23.8 ; enable bang-bang mode for the bed heater and set PWM limit
;M307 H0 B1 S1.00 ; Previous Command
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"spi.cs1" Y"rtd-max31865" ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M307 H3 A-1 C-1 D-1 ; Disable the 3rd Heater to free up PWM channel
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0.5 H1 T45 ; Elvis, The S0.5 is setup for a 12V Fan, set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S0.20 H-1 ; Elvis, The 0.20 is setup for a 5V Fan, set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0.0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B115200 ; Elvis, Go into the setup of your PanalDue and set the baud rate to 115200, enable support for PanelDue
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Tue Jun 09 2020 17:58:52 GMT-0700 (Mountain Standard Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-235 Y-215 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-235 Y-215 F360 ; move slowly to X and Y axis endstops once more (second pass)
G90 ; absolute positioning
G1 X100 Y100 F6000 ; go to first bed probe point and home Z
G30 ;home Z by probing the bed -
@Elvis0z to be sure: your BLtouch is right and behind the nozzle?
-
Yep right and behind
-
@Elvis0z are you sure G31 Z is 0? This would mean the BLtouch triggers when the nozzle touches the bed.
Please recheck steps 5-7 in https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe#Section_Calibrate_the_Z_probe_trigger_height . You could trial and error some values for Z also... (Z positive) - I would do that
I don't see other problems, I would only remove the + signs from
G31 P25 X+41 Y+10 Z0.0
they will probably be interpreted correctly, but I didn't see + signs in the examples, so to be sure, I would remove them. -
I cant go down on the z
As it won't home z
Should I just manually move the hotend to the bed -
@Elvis0z you can of course move Z carefully down with the small G1 Z movements (+Z0.1 etc) until you have the famous one-sheet-paper-distance, then say G92 Z0 to set 0 position. But this is no general solution. There must be a reason why it is not working as expected.
Maybe someone other has an idea what's wrong. -
-
@Elvis0z said in Bltouch setup need help:
Error: Z probe was not triggered during probing move
Error: Homing failedDouble check your white wire.
M558 P9 C"^zprobe.in" H5 F60 T6000 A10 R0.5
You can try removing the^in front of zprobe.in -
Thanks heaps hey. I'm futher ahead than I have been. At least its moving and the probe works with M401 and 2. That did not work befor
-
@Elvis0z said in Bltouch setup need help:
Hey guys need help to set this up its a v1.0 bltouch.
Is this a version with the trace to cut or does it come with the resistor? It's been a long time since I've seen anyone with a V1, so I'm wondering if it matters in this case. If it's a new Duet 1.04 it can't be hurt by 5v, but perhaps there is something in the BLtouch that will not trigger. If removing the ^ and checking your white wire is fruitless, maybe look into the trace/resistor
-
No I replaced it with a v3.1 that I had
