Temprature sensor error unknown temperature sensor channel
-
@Phaedrux i extracted to documents then uploaded the lot from there?
-
The zip files are meant to be uploaded as is. The DWC handles the extraction and firmware installation. This also ensures you have all the required IAP files and DWC files.
When you send M115 what does it say is installed for firmware version?
-
@Phaedrux version 3 now
-
Alright, if 3.0 is installed you should try replacing the DWC files with the zip linked above. That may get you back on track.
Once in the web interface, just upload the whole 3.0 zip file as is to the /sys folder in DWC. Then upload the 3.1.1 zip file. Don't extract them first.
-
@Phaedrux i cant get in the web interface it is just a blank screen? sorry to be such a pain .
-
@Phaedrux said in Temprature sensor error unknown temperature sensor channel:
If the web interface wasn't updated along the way with the firmware, you can manually install the DWC files by extracting the DWC zip file into the /www folder on the SD card with your PC.
https://github.com/Duet3D/RepRapFirmware/releases/download/3.1.1/DuetWebControl-SD-3.1.1.zip
You'll have to do this.
-
@Phaedrux im hopeless at this stuff ! i loaded that file onto the sd card and now i get this message from the web face
Your Duet rejected the HTTP request: page not found
Check that the SD card is mounted and has the correct files in its /www folder -
@JTM said in Temprature sensor error unknown temperature sensor channel:
i loaded that file onto the sd card
you have to upack the zip file
the content of the zip file has to be in the folder www on the sd card
-
@Veti i extracted those files to the sd card www file? is that right?
-
@Veti i switched it on and off and now its working !!!! i have web interface again !
-
now my zprobe doesnt deploy
on the bright side the temp probe is showing temp, but when i tried to heat the hotend i got an error it was too slow. -
Alright you're getting somewhere.
Have you uploaded the 3.0 and 3.1.1 zip files?
@Phaedrux said in Temprature sensor error unknown temperature sensor channel:
Alright, if 3.0 is installed you should try replacing the DWC files with the zip linked above. That may get you back on track.
Once in the web interface, just upload the whole 3.0 zip file as is to the /sys folder in DWC. Then upload the 3.1.1 zip file. Don't extract them first.
-
@Phaedrux yes mate, when sending the M115 command i now get firmware 3.1.1
-
The heaters will need to be PID tuned. That should get rid of the too slow error.
Here's how: https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+4:+Calibration/40#s161
For the probe please post your config.g and deployprobe.g and retractprobe.g macros from the /sys folder. Also homeall.g
Copy and paste the text here.
-
@Phaedrux the z probe code
; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 M558 P9 H5 F100 T2000 ; set Z probe type to bltouch and the dive height + speeds
G31 X0 Y0 Z0 P25 ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20 ; define mesh grid -
@Phaedrux deploy probe M280 P3 S10 I1 ; deploy BLTouch
retract probe M280 P3 S90 I1 ; retract BLTouch
homeall G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-505 Y-455 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-505 Y-455 F600 ; move slowly to X and Y axis endstops once more (second pass)
G90 ; absolute positioning
G1 X15 Y15 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning -
In the deploy and retract files change the P3 to P0 and remove the I1
-
@Phaedrux i changed the macro test files to P0 and delted the I1 but didnt work, re added the I1 and the macros work, but when i try to home z i get this error message?
G28 Z
Error: in file macro line 9: G30: Z probe 0 not found
Error: Homing failed -
thanks everyone for your help, it is really appreciated !
-
@JTM said in Temprature sensor error unknown temperature sensor channel:
M558 M558 P9 H5 F100 T2000 ; set Z probe type to bltouch and the dive height + speeds
Does that line in your config.g actually have double M558 at the start?
Can you post your full config.g?
