BL Touch

peter247

if it doesn't do that it is a bltouch fault and not a configuration fault.
pull the pin and see if it is bent

Gost101

I legit unplugged the bl touch wires and plugged them back in. It did the move thing and actually homed z. lol

peter247

if you get the red flash the deploy and retract doesn't work until you reset it.
reset it by power recycle OR S160 , eg M280 P3 S160

Gost101

Granted it didnt stop and kept going but progress

Gost101

The Z axis wont stop moving down even after the plunger is pushed in.

peter247

@Gost101

can you deploy and retract the probe ?

Gost101

@peter247 I can deploy and retract the probe

Veti

the wires that come with the bltouch are notoriously bad.

Gost101

@Veti Also not long enough to reach my board. lol

peter247

@Gost101

Look like you are using G30 to lower the head on homing .
Can't see a fault on your config.g , but i'm on version 3.1.1 which is different.

Gost101

@peter247 Now the printer wont home Z. lol here is the code for home all. I cannot pin up and down:

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Sep 27 2020 23:42:27 GMT-0600 (Mountain Daylight Time)
; Y-Axis
G91                ; relative positioning
G1 S1 Y-505 F1800  ; move quickly to Y axis endstop and stop there (first pass)
G1 Y5 F500         ; go back a few mm
G1 S1 Y-505 F360   ; move slowly to Y axis endstop once more (second pass)
G90                ; absolute positioning
; X-Axis
G91                ; relative positioning
G1 S1 X-505 F1800  ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F500         ; go back a few mm
G1 S1 X-505 F360   ; move slowly to X axis endstop once more (second pass)
G90                ; absolute positioning
; Z-Axis
M280 P7 S160
M280 P7 S120
M280 P7 S90 I1         ; Probe Up
M280 P7 S10 I1         ; Probe Down
M280 P7 S90 I1         ; Probe Up
M280 P7 S10 I1         ; Probe Down
M280 P7 S90 I1         ; Probe Up
M280 P7 S10 I1         ; Probe Down
G1 X15 Y15 Z10 F500
G91                    ; relative positioning
G30 		       ; Do a single probe to home our Z axis
G90 		       ; Make sure we are in absolute mode
G1 Z10 F6000           ; Rapidly move the Z axis to Z=10.

Gost101

@peter247 said in BL Touch:

M280 P3 S160

The only way to clear the blinking red light is to manually unplug the red wire: alt text

Gost101

This isn't a actually picture of my board just one I found online.

Gost101

@peter247 I tired the M280 P7 S160 through both the gcode console and in home all and it dindn't work

peter247

@Gost101

Does the up down up down up down work ?

Gost101

Nope. lol. I manually reset the bl touch but am curious if there is a reset g code for this problem.

peter247

@Gost101

this my reset code for the bltouch M280 P0 S160

peter247

@Gost101

M280 P7 S90 I1 ; Probe Up
M280 P7 S10 I1 ; Probe Down
M280 P7 S90 I1 ; Probe Up
M280 P7 S10 I1 ; Probe Down
M280 P7 S90 I1 ; Probe Up
M280 P7 S10 I1 ; Probe Down

does this work ?

Gost101

@peter247 It doesn't so far, I get error:

G28

Error: G0/G1: insufficient axes homed

after the X&Y axis home but Z wont home:

; Y-Axis
G91                ; relative positioning
G1 S1 Y-505 F1800  ; move quickly to Y axis endstop and stop there (first pass)
G1 Y5 F500         ; go back a few mm
G1 S1 Y-505 F360   ; move slowly to Y axis endstop once more (second pass)
G90                ; absolute positioning
; X-Axis
G91                ; relative positioning
G1 S1 X-505 F1800  ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F500         ; go back a few mm
G1 S1 X-505 F360   ; move slowly to X axis endstop once more (second pass)
G90                ; absolute positioning
; Z-Axis
;M280 P0 S160          ;This didn't work
M280 P7 S160
M280 P7 S90 I1         ; Probe Up
M280 P7 S10 I1         ; Probe Down
M280 P7 S90 I1         ; Probe Up
M280 P7 S10 I1         ; Probe Down
M280 P7 S90 I1         ; Probe Up
M280 P7 S10 I1         ; Probe Down
G1 X15 Y15 Z10 F500
G91                    ; relative positioning
G30 		       ; Do a single probe to home our Z axis
G90 		       ; Make sure we are in absolute mode
G1 Z10 F6000           ; Rapidly move the Z axis to Z=10.

peter247

@Gost101

M280 P7 S90 I1 ; Probe Up
M280 P7 S10 I1 ; Probe Down
M280 P7 S90 I1 ; Probe Up
M280 P7 S10 I1 ; Probe Down
M280 P7 S90 I1 ; Probe Up
M280 P7 S10 I1 ; Probe Down

this Just checks the probe not homing .
You need to home X and Y before you can home Z