• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

BLTouch Pin won't come out

Scheduled Pinned Locked Moved
General Discussion
3
14
497
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    heinrich.platau
    last edited by 15 Jan 2021, 20:15

    Hello everyone,

    I followed the tutorial from betrue3d.dk to set up my BLTouch.

    BLTouch is wired to "heater7" just like in the tutorial.

    Unfortunately the pin from my BLTouch will not go down when I send "M280 P7 S10"

    Can you help me out? What's the problem?

    When turning on the printer, the BLTouch lights red and the pin comes out two times automatically and drives in (lifts up). That's it. No manually positioning of the pin.

    undefined 1 Reply Last reply 15 Jan 2021, 20:40 Reply Quote 0
    • undefined
      Veti
      last edited by 15 Jan 2021, 20:33

      post your config.

      output of M115

      and a picture of your wiring

      undefined 1 Reply Last reply 15 Jan 2021, 20:38 Reply Quote 0
      • undefined
        heinrich.platau @Veti
        last edited by 15 Jan 2021, 20:38

        @Veti do you mean just the config.g or all config files?

        M115
        FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.2-RC2 ELECTRONICS: Duet Ethernet 1.02 or later FIRMWARE_DATE: 2020-12-24

        I post my wiring in some minutes

        undefined 1 Reply Last reply 15 Jan 2021, 20:42 Reply Quote 0
        • undefined
          Veti @heinrich.platau
          last edited by 15 Jan 2021, 20:40

          @heinrich-platau said in BLTouch Pin won't come out:

          M280 P7 S10

          ok this is not the command for version 3 firmware

          version 3 is
          M280 P0 S10

          i would suggest that you generate the config with the configurtor, as it will generate it correctly for version 3

          also post your config.g

          1 Reply Last reply Reply Quote 0
          • undefined
            heinrich.platau
            last edited by 15 Jan 2021, 20:40

            retractprobe.g deployprobe.g config.g

            1 Reply Last reply Reply Quote 0
            • undefined
              Phaedrux Moderator @heinrich.platau
              last edited by 15 Jan 2021, 20:42

              @heinrich-platau said in BLTouch Pin won't come out:

              t FIRMWARE_VERSION: 3.2-RC2

              Also please update your firmware to 3.2 final. Upload this zip file as is to the system tab in DWC.

              https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/Duet2and3Firmware-3.2.zip

              Z-Bot CoreXY Build | Thingiverse Profile

              1 Reply Last reply Reply Quote 0
              • undefined
                heinrich.platau
                last edited by 15 Jan 2021, 20:42

                ; Configuration file for Duet WiFi (firmware version 3)
                ; executed by the firmware on start-up
                ;
                ; generated by RepRapFirmware Configuration Tool v3.2.1 on Fri Jan 15 2021 19:04:07 GMT+0100 (Mitteleuropäische Normalzeit)

                ; General preferences
                G90 ; send absolute coordinates...
                M83 ; ...but relative extruder moves
                M550 P"X400-PLATAU" ; set printer name

                ; Network
                M552 P172.192.196.112 S1 ; enable network and set IP address
                M553 P255.255.255.0 ; set netmask
                M554 P172.192.196.1 ; set gateway
                M586 P0 S1 ; enable HTTP
                M586 P1 S0 ; disable FTP
                M586 P2 S0 ; disable Telnet

                ; Drives
                M569 P0 S1 ; physical drive 0 goes forwards
                M569 P1 S0 ; physical drive 1 goes backwards
                M569 P2 S0 ; physical drive 2 goes backwards
                M569 P3 S1 ; physical drive 3 goes forwards
                M584 X0 Y1:4 Z2 E3 ; set drive mapping
                M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                M92 X66.67 Y66.67 Z2400.00 E420.00 ; set steps per mm
                M566 X900.00 Y900.00 Z60.00 E480.00 ; set maximum instantaneous speed changes (mm/min)
                M203 X24000.00 Y24000.00 Z300.00 E4800.00 ; set maximum speeds (mm/min)
                M201 X2000.00 Y2000.00 Z80.00 E800.00 ; set accelerations (mm/s^2)
                M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
                M84 S30 ; Set idle timeout

                ; Axis Limits
                M208 X0 Y0 Z0 S1 ; set axis minima
                M208 X400 Y400 Z320 S0 ; set axis maxima

                ; Endstops
                M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
                M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
                M574 Z1 S2 ; configure Z-probe endstop for low end on Z

                ; Z-Probe
                M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch
                M558 P9 C"^zprobe.in" H5 F500 T4000 X0 Y0 Z1 ; set Z probe type to bltouch and the dive height + speeds
                G31 P500 X-37 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
                M557 X15:385 Y15:385 S20 ; define mesh grid

                ; Heaters
                M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
                M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
                M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                M140 H0 ; map heated bed to heater 0
                M143 H0 S120 ; set temperature limit for heater 0 to 120C
                M307 H0 R0.085 C1598.722:1598.722 D40.63 S1.00 V24.3 B0 ; set the process parameters for heater 0
                M308 S1 P"e0temp" Y"thermistor" T500000 B4723 C1.19622e-7 ; configure sensor 1 as thermistor on pin e0temp
                M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
                M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                M143 H1 S350 ; set temperature limit for heater 1 to 350C
                M950 P0 C"exp. heater7" ; BLTouch - Heaters. Disable the 7th Heater to free up PWM channel 5 on the DuexBoard (Outbreak-Port)

                ; Fans
                M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
                M106 P0 C"Druckteil-Kühler" S0 H1 T200 ; set fan 0 name and value. Thermostatic control is turned on
                M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                M106 P1 C"HotEnd-Lüfter" S1 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on

                ; Tools
                M563 P0 D0 H1 F0 ; define tool 0
                G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                ; Custom settings are not defined

                ; Miscellaneous
                M575 P1 S1 B57600 ; enable support for PanelDue
                M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

                1 Reply Last reply Reply Quote 0
                • undefined
                  Phaedrux Moderator
                  last edited by 15 Jan 2021, 20:43

                  Your retract and deploy macros need to change.

                  M280 P7 S90 I1 ; retract BLTouch

                  The P7 needs to be P0 in both. And remove the I1.

                  Z-Bot CoreXY Build | Thingiverse Profile

                  undefined 1 Reply Last reply 15 Jan 2021, 20:49 Reply Quote 0
                  • undefined
                    Veti
                    last edited by Veti 15 Jan 2021, 20:44

                    M950 P0 C"exp. heater7" ; BLTouch - Heaters. Disable the 7th Heater to free up PWM channel 5 on the DuexBoard (Outbreak-Port)

                    remove this line

                    M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
                    M106 P0 C"Druckteil-Kühler" S0 H1 T200 ; set fan 0 name and value. Thermostatic control is turned on
                    M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                    M106 P1 C"HotEnd-Lüfter" S1 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on

                    this means you have no part cooling fan. is that really what you want?

                    M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent

                    is that the correct current for your motors?

                    FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.2-RC2

                    please update to 3.2 final

                    undefined 1 Reply Last reply 15 Jan 2021, 20:54 Reply Quote 0
                    • undefined
                      heinrich.platau @Phaedrux
                      last edited by 15 Jan 2021, 20:49

                      @Phaedrux thank you,

                      I have changed the macros to P0.

                      Also I have updated the firmware to 3.2 final.

                      1 Reply Last reply Reply Quote 0
                      • undefined
                        Phaedrux Moderator
                        last edited by 15 Jan 2021, 20:53

                        Send M98 P"config.g" to check the rest of your config.g for any syntax errors.

                        Z-Bot CoreXY Build | Thingiverse Profile

                        undefined 1 Reply Last reply 15 Jan 2021, 20:56 Reply Quote 0
                        • undefined
                          heinrich.platau @Veti
                          last edited by 15 Jan 2021, 20:54

                          @Veti thank you very much Veti

                          after removing the line M950 P0C"exp. heater7" the BLTouch works.

                          Can you please help me further with you other questiones.

                          Just right now I don't have installed a part cooling fan. But I thought that I've configured the duet so, that there is a part cooling fan and I will just need to plug the fan in.

                          (First I need to order 24V Fans. My old fans from the old setup were 12V Fans)

                          The current for my motors? It's 800 mA for each motor. That's the default in configtool.... I haven't tuned them so far. Do you have another suggestion for default setting for the current?

                          1 Reply Last reply Reply Quote 0
                          • undefined
                            heinrich.platau @Phaedrux
                            last edited by 15 Jan 2021, 20:56

                            @Phaedrux after sending M98 duet says:

                            M98 P"config.g"
                            HTTP is enabled on port 80
                            FTP is disabled
                            TELNET is disabled

                            HTTP is enabled on port 80
                            FTP is disabled
                            TELNET is disabled

                            HTTP is enabled on port 80
                            FTP is disabled
                            TELNET is disabled

                            What does this mean? That I have duplicate lines in my config?

                            1 Reply Last reply Reply Quote 0
                            • undefined
                              Veti
                              last edited by Veti 15 Jan 2021, 20:57

                              @Veti said in BLTouch Pin won't come out:

                              M106 P0 C"Druckteil-Kühler" S0 H1 T200

                              you want

                              M106 P0 C"Druckteil-Kühler" S0 H-1

                              this allows the slicer to control the fan with the M106 command.

                              if you have a buck converted you can use 12v fans with the duet.
                              if you connect 12v to the v_fan selector pin.
                              see https://cdn.thingiverse.com/assets/aa/49/81/b2/23/wiring_12v_fan_on_24v_system-min.jpg

                              The current for my motors? It's 800 mA for each motor. That's the default in configtool.... I haven't tuned them so far. Do you have another suggestion for default setting for the current?

                              go for 75% of the rated current of the motors.

                              1 Reply Last reply Reply Quote 0
                              8 out of 14
                              • First post
                                8/14
                                Last post
                              Unless otherwise noted, all forum content is licensed under CC-BY-SA