BLTouch Pin won't come out

heinrich.platau

@Veti do you mean just the config.g or all config files?

M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.2-RC2 ELECTRONICS: Duet Ethernet 1.02 or later FIRMWARE_DATE: 2020-12-24

I post my wiring in some minutes

Veti

@heinrich-platau said in BLTouch Pin won't come out:

M280 P7 S10

ok this is not the command for version 3 firmware

version 3 is
M280 P0 S10

i would suggest that you generate the config with the configurtor, as it will generate it correctly for version 3

also post your config.g

heinrich.platau

retractprobe.g deployprobe.g config.g

Phaedrux

@heinrich-platau said in BLTouch Pin won't come out:

t FIRMWARE_VERSION: 3.2-RC2

Also please update your firmware to 3.2 final. Upload this zip file as is to the system tab in DWC.

https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/Duet2and3Firmware-3.2.zip

heinrich.platau

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.1 on Fri Jan 15 2021 19:04:07 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"X400-PLATAU" ; set printer name

; Network
M552 P172.192.196.112 S1 ; enable network and set IP address
M553 P255.255.255.0 ; set netmask
M554 P172.192.196.1 ; set gateway
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1:4 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X66.67 Y66.67 Z2400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E480.00 ; set maximum instantaneous speed changes (mm/min)
M203 X24000.00 Y24000.00 Z300.00 E4800.00 ; set maximum speeds (mm/min)
M201 X2000.00 Y2000.00 Z80.00 E800.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X400 Y400 Z320 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F500 T4000 X0 Y0 Z1 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-37 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X15:385 Y15:385 S20 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 R0.085 C1598.722:1598.722 D40.63 S1.00 V24.3 B0 ; set the process parameters for heater 0
M308 S1 P"e0temp" Y"thermistor" T500000 B4723 C1.19622e-7 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S350 ; set temperature limit for heater 1 to 350C
M950 P0 C"exp. heater7" ; BLTouch - Heaters. Disable the 7th Heater to free up PWM channel 5 on the DuexBoard (Outbreak-Port)

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"Druckteil-Kühler" S0 H1 T200 ; set fan 0 name and value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"HotEnd-Lüfter" S1 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

Phaedrux

Your retract and deploy macros need to change.

M280 P7 S90 I1 ; retract BLTouch

The P7 needs to be P0 in both. And remove the I1.

Veti

M950 P0 C"exp. heater7" ; BLTouch - Heaters. Disable the 7th Heater to free up PWM channel 5 on the DuexBoard (Outbreak-Port)

remove this line

M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"Druckteil-Kühler" S0 H1 T200 ; set fan 0 name and value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"HotEnd-Lüfter" S1 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on

this means you have no part cooling fan. is that really what you want?

M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent

is that the correct current for your motors?

FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.2-RC2

please update to 3.2 final

heinrich.platau

@Phaedrux thank you,

I have changed the macros to P0.

Also I have updated the firmware to 3.2 final.

Phaedrux

Send M98 P"config.g" to check the rest of your config.g for any syntax errors.

heinrich.platau

@Veti thank you very much Veti

after removing the line M950 P0C"exp. heater7" the BLTouch works.

Can you please help me further with you other questiones.

Just right now I don't have installed a part cooling fan. But I thought that I've configured the duet so, that there is a part cooling fan and I will just need to plug the fan in.

(First I need to order 24V Fans. My old fans from the old setup were 12V Fans)

The current for my motors? It's 800 mA for each motor. That's the default in configtool.... I haven't tuned them so far. Do you have another suggestion for default setting for the current?

heinrich.platau

@Phaedrux after sending M98 duet says:

M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

What does this mean? That I have duplicate lines in my config?

Veti

@Veti said in BLTouch Pin won't come out:

M106 P0 C"Druckteil-Kühler" S0 H1 T200

you want

M106 P0 C"Druckteil-Kühler" S0 H-1

this allows the slicer to control the fan with the M106 command.

if you have a buck converted you can use 12v fans with the duet.
if you connect 12v to the v_fan selector pin.
see https://cdn.thingiverse.com/assets/aa/49/81/b2/23/wiring_12v_fan_on_24v_system-min.jpg

The current for my motors? It's 800 mA for each motor. That's the default in configtool.... I haven't tuned them so far. Do you have another suggestion for default setting for the current?

go for 75% of the rated current of the motors.