Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    New to the duet COMPLETE NEWBIE

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    5
    101
    5.6k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • jay_s_ukundefined
      jay_s_uk
      last edited by

      once you've regenerated your firmware, repost your config and we can help you out.
      Also, if its an off the shelf printer, tell it what it is so we can have a bit more info.
      If you had it running under marlin, make sure you have your previous config available so we can ask questions

      Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

      gabrealekundefined 2 Replies Last reply Reply Quote 0
      • gabrealekundefined
        gabrealek @jay_s_uk
        last edited by

        @jay_s_uk I went into cura and found this config for my printer, idk if this is the old config for it. I have a CR-10 . .

        M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
        M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
        M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
        M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk
        M220 S100 ;Reset Feedrate
        M221 S100 ;Reset Flowrate

        G28 ;Home

        G92 E0 ;Reset Extruder
        G1 Z2.0 F3000 ;Move Z Axis up
        G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
        G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
        G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
        G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
        G92 E0 ;Reset Extruder
        G1 Z2.0 F3000 ;Move Z Axis up

        END GCODE

        G91 ;Relative positioning
        G1 E-2 F2700 ;Retract a bit
        G1 E-2 Z0.2 F2400 ;Retract and raise Z
        G1 X5 Y5 F3000 ;Wipe out
        G1 Z10 ;Raise Z more
        G90 ;Absolute positionning

        G1 X0 Y{machine_depth} ;Present print
        M106 S0 ;Turn-off fan
        M104 S0 ;Turn-off hotend
        M140 S0 ;Turn-off bed

        M84 X Y E ;Disable all steppers but Z

        Idk if this is exactly what you need, i still dont know how to find my old config . .

        gabrealekundefined Phaedruxundefined 2 Replies Last reply Reply Quote 0
        • gabrealekundefined
          gabrealek @gabrealek
          last edited by

          @gabrealek this is from when i printer from the stock CR-10 motherboard V1.1.4

          1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator @gabrealek
            last edited by

            @gabrealek said in New to the duet COMPLETE NEWBIE:

            M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
            M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
            M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
            M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk

            Remove that from the cura start gcode for starters.

            Z-Bot CoreXY Build | Thingiverse Profile

            1 Reply Last reply Reply Quote 0
            • Phaedruxundefined
              Phaedrux Moderator @gabrealek
              last edited by

              @gabrealek said in New to the duet COMPLETE NEWBIE:

              I am trying to balance fixing this with dealing with my two children under 7.. please help
              at this point i dont know what anything is anymore, i GIVE UP as of NOW, until i get help that is.

              Don't despair. You've come to the right place. We can't help you with your children, but I'm quite confident we can get your printer sorted. Then maybe print them some toys.

              Z-Bot CoreXY Build | Thingiverse Profile

              1 Reply Last reply Reply Quote 1
              • Phaedruxundefined
                Phaedrux Moderator
                last edited by

                What state are you currently at? I mean with the printer, not mentally.

                Is it all wired up? Do you have the Duet Web Control interface up?

                Assuming you do, please send M122 in the console tab and post the results. Assuming the firmware updates worked you should be running 3.2

                The format of your config.g is for RRF2 though, so you'll need to generate a fresh config file set using the online tool.

                https://configtool.reprapfirmware.org/Start

                Enter the information as best you can and then download the resulting zip file and upload that to the system tab in DWC.

                Then post your config.g, homeall, homex, homey, homez here.

                Z-Bot CoreXY Build | Thingiverse Profile

                gabrealekundefined 1 Reply Last reply Reply Quote 0
                • gabrealekundefined
                  gabrealek @Phaedrux
                  last edited by

                  @Phaedrux Okay, So im wired up and in the DWC interface. I just updated
                  "FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.2 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2021-01-05"

                  Im in the RRF config now. . You guys have already made me feel so much better and secure. . i was loosing my marbles!! 😞

                  1 Reply Last reply Reply Quote 0
                  • gabrealekundefined
                    gabrealek @jay_s_uk
                    last edited by gabrealek

                    @jay_s_uk @Phaedrux

                    Okay so for everything i was unsure about, I left it at default.

                    Here is the config i just finished

                    ; Configuration file for Duet WiFi (firmware version 3)
                    ; executed by the firmware on start-up
                    ;
                    ; generated by RepRapFirmware Configuration Tool v3.2.1 on Mon Jan 18 2021 18:02:52 GMT-0500 (Eastern Standard Time)

                    ; General preferences
                    G90 ; send absolute coordinates...
                    M83 ; ...but relative extruder moves
                    M550 P"Creola" ; set printer name

                    ; Network
                    M552 S1 ; enable network
                    M586 P0 S1 ; enable HTTP
                    M586 P1 S0 ; disable FTP
                    M586 P2 S0 ; disable Telnet

                    ; Drives
                    M569 P0 S1 ; physical drive 0 goes forwards
                    M569 P1 S1 ; physical drive 1 goes forwards
                    M569 P2 S1 ; physical drive 2 goes forwards
                    M569 P3 S1 ; physical drive 3 goes forwards
                    M584 X0 Y1 Z2 E3 ; set drive mapping
                    M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                    M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm
                    M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                    M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
                    M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
                    M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
                    M84 S30 ; Set idle timeout

                    ; Axis Limits
                    M208 X0 Y0 Z0 S1 ; set axis minima
                    M208 X300 Y300 Z400 S0 ; set axis maxima

                    ; Endstops
                    M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
                    M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
                    M574 Z1 S1 P"!zstop" ; configure active-high endstop for low end on Z via pin !zstop

                    ; Z-Probe
                    M558 P1 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
                    G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
                    M557 X15:215 Y15:195 S20 ; define mesh grid

                    ; Heaters
                    M308 S0 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin e0temp
                    M950 H0 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0
                    M307 H0 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                    M143 H0 S245 ; set temperature limit for heater 0 to 245C
                    M308 S1 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin bedtemp
                    M950 H1 C"bedheat" T1 ; create bed heater output on bedheat and map it to sensor 1
                    M307 H1 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
                    M140 H1 ; map heated bed to heater 1
                    M143 H1 S80 ; set temperature limit for heater 1 to 80C

                    ; Fans
                    M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
                    M106 P0 S0 H1 T45 ; set fan 0 value. Thermostatic control is turned on
                    M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                    M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off

                    ; Tools
                    M563 P0 S"Extruder" D0 H1 F0:1 ; define tool 0
                    G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                    G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
                    M563 P1 S"Bed" F0 ; define tool 1
                    G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
                    G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

                    ; Custom settings are not defined

                    My printer model is a stock CR-10. no modifications. .

                    1 Reply Last reply Reply Quote 0
                    • Phaedruxundefined
                      Phaedrux Moderator
                      last edited by

                      Maybe take a look at this guide series that goes through the whole process. Might give you some ideas. It's for an ender 3 and RRF2, which is pretty similar to the CR-10 actually. All Creality printers are similar.

                      https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+1:+Wiring/37

                      The RRF3 version is started here, but still working on it.

                      https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+3+Mini+5++Guide+Part+1:+Wiring/87

                      Z-Bot CoreXY Build | Thingiverse Profile

                      1 Reply Last reply Reply Quote 0
                      • gabrealekundefined
                        gabrealek
                        last edited by gabrealek

                        ; Configuration file for Duet WiFi (firmware version 3)
                        ; executed by the firmware on start-up
                        ;
                        ; generated by RepRapFirmware Configuration Tool v3.2.1 on Tue Jan 19 2021 15:22:13 GMT-0500 (Eastern Standard Time)

                        ; General preferences
                        G90 ; send absolute coordinates...
                        M83 ; ...but relative extruder moves
                        M550 P"Creola" ; set printer name

                        ; Network
                        M552 S1 ; enable network
                        M586 P0 S1 ; enable HTTP
                        M586 P1 S0 ; disable FTP
                        M586 P2 S0 ; disable Telnet

                        ; Drives
                        M569 P0 S0 ; physical drive 0 goes backwards
                        M569 P1 S0 ; physical drive 1 goes backwards
                        M569 P2 S1 ; physical drive 2 goes forwards
                        M569 P3 S0 ; physical drive 3 goes backwards
                        M584 X0 Y1 Z2 E3 ; set drive mapping
                        M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                        M92 X80.00 Y80.00 Z400.00 E93.00 ; set steps per mm
                        M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                        M203 X6000.00 Y6000.00 Z600.00 E1200.00 ; set maximum speeds (mm/min)
                        M201 X500.00 Y500.00 Z120.00 E250.00 ; set accelerations (mm/s^2)
                        M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
                        M84 S30 ; Set idle timeout

                        ; Axis Limits
                        M208 X0 Y0 Z0 S1 ; set axis minima
                        M208 X300 Y300 Z400 S0 ; set axis maxima

                        ; Endstops
                        M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
                        M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
                        M574 Z1 S1 P"!zstop" ; configure active-high endstop for low end on Z via pin !zstop

                        ; Z-Probe
                        M558 P0 H18 F120 T480000 ; disable Z probe but set dive height, probe speed and travel speed
                        M557 X10:220 Y10:220 S20 ; define mesh grid

                        ; Heaters
                        M308 S0 P"e0temp" Y"thermistor" T9880 B4185 ; configure sensor 0 as thermistor on pin e0temp
                        M950 H0 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0
                        M307 H0 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                        M143 H0 S250 ; set temperature limit for heater 0 to 250C
                        M308 S1 P"bedtemp" Y"thermistor" T9880 B4185 ; configure sensor 1 as thermistor on pin bedtemp
                        M950 H1 C"bedheat" T1 ; create bed heater output on bedheat and map it to sensor 1
                        M307 H1 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                        M140 H1 ; map heated bed to heater 1
                        M143 H1 S80 ; set temperature limit for heater 1 to 80C

                        ; Fans
                        M950 F0 C"fan0" Q20 ; create fan 0 on pin fan0 and set its frequency
                        M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
                        M950 F1 C"fan1" Q20 ; create fan 1 on pin fan1 and set its frequency
                        M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

                        ; Tools
                        M563 P0 S"Extruder" D0 F0:1 ; define tool 0
                        G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                        G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                        ; Custom settings are not defined

                        ; Miscellaneous
                        M501 ; load saved parameters from non-volatile memory
                        M911 S21 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

                        ; homeall.g
                        ; called to home all axes
                        ;
                        ; generated by RepRapFirmware Configuration Tool v3.2.1 on Tue Jan 19 2021 15:30:54 GMT-0500 (Eastern Standard Time)
                        G91 ; relative positioning
                        G1 H2 Z18 F480000 ; lift Z relative to current position
                        G1 H1 X-305 Y-305 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
                        G1 H2 X5 Y5 F480000 ; go back a few mm
                        G1 H1 X-305 Y-305 F3600 ; move slowly to X and Y axis endstops once more (second pass)
                        G1 H1 Z-405 F3600 ; move Z down stopping at the endstop
                        G90 ; absolute positioning
                        G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

                        ; Uncomment the following lines to lift Z after probing
                        ;G91 ; relative positioning
                        ;G1 Z18 F8000 ; lift Z relative to current position
                        ;G90 ; absolute positioning

                        ; homex.g
                        ; called to home the X axis
                        ;
                        ; generated by RepRapFirmware Configuration Tool v3.2.1 on Tue Jan 19 2021 15:31:40 GMT-0500 (Eastern Standard Time)
                        G91 ; relative positioning
                        G1 H2 Z18 F480000 ; lift Z relative to current position
                        G1 H1 X-305 F3000 ; move quickly to X axis endstop and stop there (first pass)
                        G1 H2 X5 F480000 ; go back a few mm
                        G1 H1 X-305 F3600 ; move slowly to X axis endstop once more (second pass)
                        G1 H2 Z-18 F480000 ; lower Z again
                        G90 ; absolute positioning

                        ; homez.g
                        ; called to home the Z axis
                        ;
                        ; generated by RepRapFirmware Configuration Tool v3.2.1 on Tue Jan 19 2021 15:31:58 GMT-0500 (Eastern Standard Time)
                        G91 ; relative positioning
                        G1 H2 Z18 F480000 ; lift Z relative to current position
                        G1 H1 Z-405 F3000 ; move Z down until the endstop is triggered
                        G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

                        ; Uncomment the following lines to lift Z after probing
                        ;G91 ; relative positioning
                        ;G1 Z18 F8000 ; lift Z relative to current position
                        ;G90 ; absolute positioning

                        Ive checked my wiring and it all seems correct.

                        @Phaedrux

                        CURRENT.PNG

                        Phaedruxundefined 1 Reply Last reply Reply Quote 0
                        • Phaedruxundefined
                          Phaedrux Moderator @gabrealek
                          last edited by

                          @gabrealek said in New to the duet COMPLETE NEWBIE:

                          ; Heaters
                          M308 S0 P"e0temp" Y"thermistor" T9880 B4185 ; configure sensor 0 as thermistor on pin e0temp
                          M950 H0 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0
                          M307 H0 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                          M143 H0 S250 ; set temperature limit for heater 0 to 250C
                          M308 S1 P"bedtemp" Y"thermistor" T9880 B4185 ; configure sensor 1 as thermistor on pin bedtemp
                          M950 H1 C"bedheat" T1 ; create bed heater output on bedheat and map it to sensor 1
                          M307 H1 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                          M140 H1 ; map heated bed to heater 1
                          M143 H1 S80 ; set temperature limit for heater 1 to 80C

                          It would be more traditional for heater0 to be the bed heater and for heater1 to be the first tool heater. I don't think that's strictly enforced now with RRF3 being more flexible about it, but still not a bad idea to conform to the standard.

                          Also, your tool definition is lacking a heater.

                          Maybe take another crack at the config tool. https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Mini+5++Guide+Part+2:+Configuration/88

                          Z-Bot CoreXY Build | Thingiverse Profile

                          gabrealekundefined 1 Reply Last reply Reply Quote 0
                          • gabrealekundefined
                            gabrealek @Phaedrux
                            last edited by

                            @Phaedrux Okay, back into the studio I go. Thank you for helping me!!!!

                            1 Reply Last reply Reply Quote 0
                            • Phaedruxundefined
                              Phaedrux Moderator
                              last edited by

                              Double check your heater and thermistor connections as well. Hopefully that will resolve the odd heater reporting in DWC.

                              Otherwise the config looks ok so far.

                              After the heaters are sorted you'd want to carefully check the motor directions are correct and endstops are working and then test homing. And then test and tune the heaters and calibrate the extruder.

                              follow along
                              https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+3:+Commissioning/39

                              Z-Bot CoreXY Build | Thingiverse Profile

                              gabrealekundefined 1 Reply Last reply Reply Quote 0
                              • gabrealekundefined
                                gabrealek @Phaedrux
                                last edited by

                                @Phaedrux thanks. Ive checked the connections and redid them as the ender tutorial and now i am having a fault in the hotend and also the bed when i try to heat it as well.

                                1.PNG

                                Here is my new config . . ive been trying to get it right all day. ive done it exactly as the tutorial as well.

                                ; Configuration file for Duet WiFi (firmware version 3)
                                ; executed by the firmware on start-up
                                ;
                                ; generated by RepRapFirmware Configuration Tool v3.2.1 on Tue Jan 19 2021 17:33:25 GMT-0500 (Eastern Standard Time)

                                ; General preferences
                                G90 ; send absolute coordinates...
                                M83 ; ...but relative extruder moves
                                M550 P"Creola" ; set printer name

                                ; Network
                                M552 S1 ; enable network
                                M586 P0 S1 ; enable HTTP
                                M586 P1 S0 ; disable FTP
                                M586 P2 S0 ; disable Telnet

                                ; Drives
                                M569 P0 S0 ; physical drive 0 goes backwards
                                M569 P1 S0 ; physical drive 1 goes backwards
                                M569 P2 S1 ; physical drive 2 goes forwards
                                M569 P3 S0 ; physical drive 3 goes backwards
                                M584 X0 Y1 Z2 E3 ; set drive mapping
                                M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                                M92 X80.00 Y80.00 Z400.00 E93.00 ; set steps per mm
                                M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                                M203 X6000.00 Y6000.00 Z600.00 E1200.00 ; set maximum speeds (mm/min)
                                M201 X500.00 Y500.00 Z120.00 E250.00 ; set accelerations (mm/s^2)
                                M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
                                M84 S30 ; Set idle timeout

                                ; Axis Limits
                                M208 X0 Y0 Z0 S1 ; set axis minima
                                M208 X300 Y300 Z400 S0 ; set axis maxima

                                ; Endstops
                                M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
                                M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
                                M574 Z1 S1 P"!zstop" ; configure active-high endstop for low end on Z via pin !zstop

                                ; Z-Probe
                                M558 P0 H18 F120 T480000 ; disable Z probe but set dive height, probe speed and travel speed
                                M557 X10:220 Y10:220 S20 ; define mesh grid

                                ; Heaters
                                M308 S0 P"e0temp" Y"thermistor" T9880 B4185 ; configure sensor 0 as thermistor on pin e0temp
                                M950 H0 C"e0heat" T0 ; create bed heater output on e0heat and map it to sensor 0
                                M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                                M140 H0 ; map heated bed to heater 0
                                M143 H0 S250 ; set temperature limit for heater 0 to 250C
                                M308 S1 P"e1temp" Y"thermistor" T9880 B4185 ; configure sensor 1 as thermistor on pin e1temp
                                M950 H1 C"e1heat" T1 ; create nozzle heater output on e1heat and map it to sensor 1
                                M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                                M143 H1 S80 ; set temperature limit for heater 1 to 80C

                                ; Fans
                                M950 F0 C"fan0" Q20 ; create fan 0 on pin fan0 and set its frequency
                                M106 P0 C"PartCool" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off
                                M950 F1 C"fan1" Q20 ; create fan 1 on pin fan1 and set its frequency
                                M106 P1 S1 H T45 ; set fan 1 value. Thermostatic control is turned on

                                ; Tools
                                M563 P0 S"Hotend" D0 H1 F0 ; define tool 0
                                G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                                G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                                ; Custom settings are not defined

                                ; Miscellaneous
                                M501 ; load saved parameters from non-volatile memory
                                M911 S21 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                                T0 ; select first tool

                                Phaedruxundefined 1 Reply Last reply Reply Quote 0
                                • Phaedruxundefined
                                  Phaedrux Moderator @gabrealek
                                  last edited by

                                  @gabrealek said in New to the duet COMPLETE NEWBIE:

                                  T9880

                                  I think you're missing a digit in your T values.

                                  Z-Bot CoreXY Build | Thingiverse Profile

                                  gabrealekundefined 1 Reply Last reply Reply Quote 0
                                  • gabrealekundefined
                                    gabrealek @Phaedrux
                                    last edited by

                                    @Phaedrux I dont understand how i would correct that. . its in there twice. . Ive tried to look up what a T9880 is . . i cant find anything .. Is it a problem with the setting i put in the config?

                                    1 Reply Last reply Reply Quote 0
                                    • Phaedruxundefined
                                      Phaedrux Moderator
                                      last edited by

                                      The correct values are T98801

                                      Z-Bot CoreXY Build | Thingiverse Profile

                                      gabrealekundefined 1 Reply Last reply Reply Quote 0
                                      • gabrealekundefined
                                        gabrealek @Phaedrux
                                        last edited by

                                        @Phaedrux thank you. It is greatly appreciated. Also, is the estop0 supposed to light up like the x,y, and z? When I plug it in it does not light up

                                        Phaedruxundefined 1 Reply Last reply Reply Quote 0
                                        • Phaedruxundefined
                                          Phaedrux Moderator @gabrealek
                                          last edited by

                                          @gabrealek said in New to the duet COMPLETE NEWBIE:

                                          Also, is the estop0 supposed to light up like the x,y, and z? When I plug it in it does not light up

                                          That depends. What kind of switch are you plugging in as an endstop? The difference would be normally open switch or normally closed switch. The important thing is that the LED changes state when the switch is depressed.

                                          What is the intended use for the endstop?

                                          Z-Bot CoreXY Build | Thingiverse Profile

                                          gabrealekundefined 5 Replies Last reply Reply Quote 0
                                          • gabrealekundefined
                                            gabrealek @Phaedrux
                                            last edited by

                                            @Phaedrux I was just wondering. that was all .. thank you for all of your help!! i really appreciate it. Hope I didn't bother you to much. Lol

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA