• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Mini 5 (with toolboard) and leveling using X2 Motors

Scheduled Pinned Locked Moved Solved
General Discussion
4
25
969
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    JayJay @Veti
    last edited by JayJay 31 Dec 2020, 13:35

    @Veti

    yes it does.

    I re-installed my Duet-2 all is working again with the same bed.g file.

    i have compared my Duet-2 & mini-5 config's and i can see nothing wrong with the mini-5 config

    undefined 1 Reply Last reply 31 Dec 2020, 14:03 Reply Quote 0
    • undefined
      Veti @JayJay
      last edited by 31 Dec 2020, 14:03

      @JayJay

      neither can i. and the probing working sometimes is not something you can configure.

      undefined 1 Reply Last reply 31 Dec 2020, 14:42 Reply Quote 1
      • undefined
        JayJay @Veti
        last edited by 31 Dec 2020, 14:42

        @Veti said in Mini 5 (with toolboard) and leveling using X2 Motors:

        @JayJay

        neither can i. and the probing working sometimes is not something you can configure.

        Thank for the help, i will just wait and see what any of the duet team have to say , this board was a christmas gift so i will ask my uncle where he bought it

        1 Reply Last reply Reply Quote 0
        • undefined
          Phaedrux Moderator
          last edited by 31 Dec 2020, 18:13

          Firmware version? Can you post the results of M122?

          Z-Bot CoreXY Build | Thingiverse Profile

          undefined 1 Reply Last reply 1 Jan 2021, 13:13 Reply Quote 0
          • undefined
            JayJay @Phaedrux
            last edited by 1 Jan 2021, 13:13

            @Phaedrux said in Mini 5 (with toolboard) and leveling using X2 Motors:

            Firmware version? Can you post the results of M122?

            The Board is removed so the M122 will show some errors i think.

            i installed the board (and toolboard) in my core-xy , which normally has a duet-3-6hc fitted and the mini-5 runs fine in there, so im not sure why it doesnt like being in my hacked up i3, and even stranger that my Duet-2 wifi runs fine when i put it back into the i3, both printers sit side by side so its not a location related issue.

            i have been racking my brains with this one as it makes no sense at all.

            M115:

            FIRMWARE_NAME: RepRapFirmware for Duet 3 Mini 5+ FIRMWARE_VERSION: 3.2-RC2 ELECTRONICS: Duet 3 Mini5plus WiFi FIRMWARE_DATE: 2020-12-24

            M122
            === Diagnostics ===
            RepRapFirmware for Duet 3 Mini 5+ version 3.2-RC2 running on Duet 3 Mini5plus WiFi (standalone mode)
            Used output buffers: 3 of 40 (11 max)
            === RTOS ===
            Static ram: 98732
            Dynamic ram: 107196 of which 496 recycled
            Never used RAM 38792, free system stack 140 words
            Tasks: NETWORK(ready,192) HEAT(blocked,316) CanReceiv(blocked,947) CanSender(blocked,372) CanClock(blocked,360) TMC(blocked,123) MAIN(running,444) IDLE(ready,20) AIN(blocked,267)
            Owned mutexes: WiFi(NETWORK)
            === Platform ===
            Last reset 00:01:54 ago, cause: power up
            Last software reset at 2020-12-30 22:53, reason: User, GCodes spinning, available RAM 38752, slot 2
            Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00451000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
            Error status: 0x00
            Aux0 errors 0,0,0
            Aux1 errors 0,0,0
            Supply voltage: min 0.0, current 0.9, max 0.9, under voltage events: 0, over voltage events: 0, power good: no
            Driver 0: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
            Driver 1: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
            Driver 2: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
            Driver 3: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
            Driver 4: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
            Driver 5: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
            Driver 6: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
            Date/time: 2021-01-01 15:00:52
            Cache data hit count 222524317
            Slowest loop: 5.31ms; fastest: 0.11ms
            === Storage ===
            Free file entries: 10
            SD card 0 detected, interface speed: 22.5MBytes/sec
            SD card longest read time 4.2ms, write time 0.0ms, max retries 0
            === Move ===
            DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
            === MainDDARing ===
            Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
            === AuxDDARing ===
            Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
            === Heat ===
            Bed heaters = 0 -1, chamberHeaters = -1 -1
            === GCodes ===
            Segments left: 0
            Movement lock held by null
            HTTP is idle in state(s) 0
            Telnet is idle in state(s) 0
            File is idle in state(s) 0
            USB is idle in state(s) 0
            Aux is idle in state(s) 0
            Trigger is idle in state(s) 0
            Queue is idle in state(s) 0
            LCD is idle in state(s) 0
            SBC is idle in state(s) 0
            Daemon is idle in state(s) 0
            Aux2 is idle in state(s) 0
            Autopause is idle in state(s) 0
            Code queue is empty.
            === Network ===
            Slowest loop: 10.70ms; fastest: 0.00ms
            Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
            HTTP sessions: 1 of 8

            • WiFi -
              Network state is active
              WiFi module is connected to access point
              Failed messages: pending 0, notready 0, noresp 0
              WiFi firmware version 1.25beta0
              WiFi MAC address f4:cf:a2:6f:bd:af
              WiFi Vcc 3.37, reset reason Power up
              WiFi flash size 2097152, free heap 25264
              WiFi IP address 192.168.0.115
              WiFi signal strength -57dBm, mode 802.11n, reconnections 0, sleep mode modem
              Clock register 00002002
              Socket states: 0 0 0 0 0 0 0 0
              === CAN ===
              Messages queued 1015, send timeouts 1012, received 0, lost 0, longest wait 0ms for reply type 0, free buffers 16
            undefined 1 Reply Last reply 1 Jan 2021, 17:28 Reply Quote 0
            • undefined
              Phaedrux Moderator @JayJay
              last edited by 1 Jan 2021, 17:28

              @JayJay said in Mini 5 (with toolboard) and leveling using X2 Motors:

              the mini-5 runs fine in there, so im not sure why it doesnt like being in my hacked up i3

              That is confusing. An intermittent short in something connected?

              Z-Bot CoreXY Build | Thingiverse Profile

              undefined 1 Reply Last reply 5 Jan 2021, 14:27 Reply Quote 0
              • undefined
                JayJay @Phaedrux
                last edited by JayJay 1 May 2021, 14:58 5 Jan 2021, 14:27

                @Phaedrux said in Mini 5 (with toolboard) and leveling using X2 Motors:

                @JayJay said in Mini 5 (with toolboard) and leveling using X2 Motors:

                the mini-5 runs fine in there, so im not sure why it doesnt like being in my hacked up i3

                That is confusing. An intermittent short in something connected?

                its the exact same wiring between the mini-5 and the Duet-2 and i thought about that and have been probing for shorts and found nothing

                1 Reply Last reply Reply Quote 0
                • dc42undefined
                  dc42 administrators
                  last edited by dc42 1 May 2021, 15:20 5 Jan 2021, 15:16

                  Some thoughts:

                  • Is the tool board definitely running 3.2RC2 as well?
                  • Try adding a settling delay parameter (R) to the M558 command, e.g. R0.2 or R0.5
                  • You said the probe doesn't register as triggered, yet you don't get a head crash. That means either the dive height is too low to probe deep enough, or the probe trigger is being registered for the purpose of stopping the Z move but not for the purpose of recording the stop height. So try increasing the dive height - very carefully!

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  1 Reply Last reply Reply Quote 0
                  • undefined
                    JayJay
                    last edited by 20 Jan 2021, 21:52

                    @dc42
                    @Phaedrux
                    @Veti

                    Well I finally fixed it....

                    My homeall.g had G30 S-3 in the script.

                    I removed that and changed it to single G30 command on its own and now it completes the G32 action with no errors, I dont know why it works fine on my Duet-2 with the S-3 switch in my homeall but the mini 5 doesnt like it

                    dc42undefined 1 Reply Last reply 20 Jan 2021, 21:54 Reply Quote 1
                    • dc42undefined
                      dc42 administrators @JayJay
                      last edited by 20 Jan 2021, 21:54

                      @JayJay said in Mini 5 (with toolboard) and leveling using X2 Motors:

                      @dc42
                      @Phaedrux
                      @Veti

                      Well I finally fixed it....

                      My homeall.g had G30 S-3 in the script.

                      I removed that and changed it to single G30 command on its own and now it completes the G32 action with no errors, I dont know why it works fine on my Duet-2 with the S-3 switch in my homeall but the mini 5 doesnt like it

                      Perhaps your Duet 2 is running old firmware that doesn't support the S3 parameter?

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      undefined 1 Reply Last reply 20 Jan 2021, 21:59 Reply Quote 0
                      • undefined
                        JayJay @dc42
                        last edited by 20 Jan 2021, 21:59

                        @dc42 said in Mini 5 (with toolboard) and leveling using X2 Motors:

                        @JayJay said in Mini 5 (with toolboard) and leveling using X2 Motors:

                        @dc42
                        @Phaedrux
                        @Veti

                        Well I finally fixed it....

                        My homeall.g had G30 S-3 in the script.

                        I removed that and changed it to single G30 command on its own and now it completes the G32 action with no errors, I dont know why it works fine on my Duet-2 with the S-3 switch in my homeall but the mini 5 doesnt like it

                        Perhaps your Duet 2 is running old firmware that doesn't support the S3 parameter?

                        The Duet-2 was/is on Release 3.2-RC1

                        And to confirm

                        Duet-2 WOULD complete the action with G30 S-3

                        Duet-3 Mini-5+ WOULD NOT complete the action G30 S-3

                        The Mini-5+ would only complete after i removed the S-3 switch

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA