G32 ERROR

[Phaedrux]

@moe-adams9093 said in G32 ERROR:

M574 Z2 S1 p"!exp.e2stop+exp.e3stop+exp.e5stop+exp.e6stop"

You have one of the switches inverted with !, but not the rest. I assume they are all the same type of switch, yes? If so, you would need a ! before each pin name.

[moe.adams9093]

No I will do that tonight when I get back home and do some recrackin.

[moe.adams9093]

@Phaedrux man your sharp yes I think thats the problem. I will try it tonight because when I homed only that axis was moving and the rest wasn't moving at all. I thought when I combine all of them they should automatically be the same type. Thanks

[moe.adams9093]

So I went ahead and did combine all of my endstops on a single line in this order

M574 Z2 S1 p"!exp.e2stop+!exp.e3stop+!exp.e5stop+!exp.e6stop";

it crashed my firmware so I had to do a hard reset and erase firmware and reupload new firmware but this time I did install 3.2. and also I did try just one endstop
M574 Z2 S1 p"!exp.e2stop . ti did ignore the bed to go down to 500 it went to -500.

[Veti]

@moe-adams9093 said in G32 ERROR:

M574 Z2 S1 p

dunno if it matter but use a capital P

[moe.adams9093]

I tried CAP P still doing the same thing

[Veti]

@moe-adams9093 said in G32 ERROR:

it crashed my firmware

please post a M122 after the crash

[moe.adams9093]

its to late to post M112 because I already fixed this issue. now Im dealing with homing-all problem it just not working. I don't know if the duet can allow to use EndStops on max and Zprob On MIN

[fcwilt]

@moe-adams9093 said in G32 ERROR:

its to late to post M112 because I already fixed this issue. now Im dealing with homing-all problem it just not working. I don't know if the duet can allow to use EndStops on max and Zprob On MIN

Yes it can - just need to get the settings right.

Is homing using the Z end stop sensors working?

Frederick

[moe.adams9093]

so now I was able to get one end stop to work but when press the end-stop all 4 z motors stop not individually.

[moe.adams9093]

@moe-adams9093 said in G32 ERROR:
when I write this code and hit save and restart the board Deg light will flash red and the bord is not reachable at this stage so I had to manually erase the firmware and reupload all files again

M574 Z2 S1 P"!exp.e2stop+!exp.e3stop+!exp.e5stop+!exp.e6stop";

[moe.adams9093]

M574 Z2 S1 P"!duex.e2stop+!duex.e3stop+!duex.e5stop+!duex.e6stop"; 
 

this line of Code it did work but when I press any of the end-stop all 4 Z motors Stop not individually

[fcwilt]

@moe-adams9093 said in G32 ERROR:

M574 Z2 S1 P"!duex.e2stop+!duex.e3stop+!duex.e5stop+!duex.e6stop"; 
 

this line of Code it did work but when I press any of the end-stop all 4 Z motors Stop not individually

I have no idea why you should have had to erase the firmware - that makes no sense at all.

In any case since you had to upload all the files again but post config.g and homeall.g using the </> tag to be sure we are looking at the most recent.

Frederick

[Phaedrux]

Can you please send M122 and M98 P"config.g" and post the results?

We are assuming you are on RRF3 but I don't think we've actually checked yet.

@moe-adams9093 said in G32 ERROR:

I don't know if the duet can allow to use EndStops on max and Zprob On MIN

It certainly can. The endstops are configured with M574 and called into action with a G1 H1 Z move, and the probe is configured with M558/G31 and called into action with G30. So as long as both are configured, you can choose which to use by either using a G1 H1 Z move or a G30/G29.

[moe.adams9093]

@Phaedrux Ok so after long hours of troubleshooting and looking on duet documentation and also at duet form to find someone had the same issue. so at first when I added this code line to my config.g

M574 Z2 S1 P"!duex.e2stop+!duex.e3stop+!duex.e5stop+!duex.e6stop";
 

the moment when I hit save and restart the system never came back online my Degnostic light on the DuetEthernet Board was flashing red. at that stage, I went and connected via USB to enable M552S1 but my Yat Couldn't find the duet so I went ahead and jumped the 2 erase headers and reinstall the firmware everything came back as it supposed I went back a gain and added same code and it worked fine after that I'm not sure why the board did crash. so now this is my latest configuration files

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Oct 13 2020 21:14:55 GMT-0500 (Central Daylight Time)
 
; General preferences
G90                                                     	; send absolute coordinates...
M83                                                     	; ...but relative extruder moves
M550 P"DIVINCI-3D (MP4560)"                             	; set printer name
M669 K1                                                 	; select CoreXY mode
 
; Network
M552 P0.0.0.0 S1                                        	; enable network and acquire dynamic address via DHCP
M586 P0 S1                                              	; enable HTTP
M586 P1 S0                                              	; disable FTP
M586 P2 S0                                              	; disable Telnet
 
; Drives
M569 P10  R1 T2:2:2:2  S1  									; physical drive 0 goes forwards
M569 P11  R1 T2:2:2:2  S1  									; physical drive 1 goes forwards
M569 P3 S1                                             		; physical drive 3 goes forwards
M569 P4 S1                                              	; physical drive 4 goes forwards
M569 P5 S1                                              	; physical drive 5 goes Backwards
M569 P6 S1 													; physical drive 6 goes Backwards
M569 P8 S0			          								; physical drive 7 goes Backwards 
M569 P9 S0                                              	; physical drive 9 goes backwards 
M584 X10 Y11 Z5:6:8:9 E3:4                              	; set drive mapping
M671 X5.0:455.0:455.0:5.0 Y25.0:25.0:455.0:455.0 S6    	; ZBelts Near Locations                    
M350 X16 Y16 Z16 E16:16 I1                              	; configure microstepping with interpolation
M92 X40.00 Y40.00 Z410.00 E415.00:415.00 					; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00:120.00              	; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z400 E1200.00:1200.00        		; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z40.00 E250.00:250.00           		; set accelerations (mm/s^2)
M906 X1800 Y1800 Z1000 E500:500 I30                     	; set motor currents (mA) and motor idle factor in per cent
M84 S30                                                 	; Set idle timeout
 
; Axis Limits
M208 X0 Y0 Z0 S1                                        	; set axis minima
M208 X460 Y460 Z460 S0                                  	; set axis maxima
 
M574 X1 S1 P"!xstop"                                    		; configure active-high endstop for low end on X via pin !xstop
M574 Y1 S1 P"!ystop"                                    		; configure active-high endstop for low end on Y via pin !ystop
M574 Z1 S2                                              		; configure Z-probe endstop for low end on Z
M574 Z2 S1 P"!exp.e2stop+!exp.e3stop+!exp.e5stop+!exp.e6stop"	; configure Z-probe endstop for low end on Z
 
 
 
 
; Z-Probe
M558 P1 C"zprobe.in" H25 F600 T6000                      	; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5                                     	; set Z probe trigger value, offset and trigger height
M557 X20:440 Y20:440 S20                                	; define mesh grid
 
 
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4725 C7.06e-8 	; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                                   	; create bed heater output on bedheat and map it to sensor 0
M307 H0 A11 C99000 D2000 B1                  				; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                 	; map heated bed to heater 0
M143 H0 S120                                            	; set temperature limit for heater 0 to 120C
M308 S1 P"spi.cs1" Y"thermocouple-max31856"             	; configure sensor 1 as thermocouple via CS pin spi.cs1
M950 H1 C"e0heat" T1                                    	; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                        	; disable bang-bang mode for heater  and set PWM limit
M308 S2 P"spi.cs2" Y"thermocouple-max31856"             	; configure sensor 2 as thermocouple via CS pin spi.cs2
M950 H2 C"e1heat" T2                                    	; create nozzle heater output on e1heat and map it to sensor 2
M307 H2 B0 S1.00                                        	; disable bang-bang mode for heater  and set PWM limit
M308 S3 P"duex.e2temp" Y"thermistor" T10000 B3950       	; configure sensor 3 as thermistor on pin duex.e2temp
M950 H3 C"duex.e2heat" T3                               	; create chamber heater output on duex.e2heat and map it to sensor 3
M307 H3 A11 C99000 D2000 B1                             	; enable bang-bang mode for the chamber heater and set PWM limit
M141 H3                                                 	; map chamber to heater 3
 
; Fans
M950 F0 C"fan0" Q500                                    	; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H-1                                          	; set fan 0 value. Thermostatic control is turned on                           
M950 F1 C"fan1" Q500                                    	; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H2 T45                                       	; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500                                    	; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1:2 T45                                     	; set fan 2 value. Thermostatic control is turned on
 
; Tools
M563 P0 S"MAIN EXTRUDER" D0 H1 F0                       	; define tool 0
G10 P0 X0 Y0 Z0                                         	; set tool 0 axis offsets
G10 P0 R0 S0                                            	; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"SECOND EXTRUDER" D1 H2 F0                     	; define tool 1
G10 P1 X0 Y0 Z0                                         	; set tool 1 axis offsets
G10 P1 R0 S0                                            	; set initial tool 1 active and standby temperatures to 0C
 
; Custom settings are not defined
 
; Miscellaneous
M575 P1 S1 B57600                                       	; enable support for PanelDue
M501                                                    	; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"      	; set voltage thresholds and actions to run on power loss
T0                                                      	; select first tool
 
 

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Oct 13 2020 21:14:55 GMT-0500 (Central Daylight Time)
G91                     ; relative positioning
G1 H1 Z500 F6000          ; lift Z relative to current position
G1 H1 X-465 F8000 ; move quickly to X endstop and stop there (first pass)
G1 H1 Y-465 F8000 ; move quickly to Y endstop and stop there (first pass)
G1 H2 X5 Y5 F6000       ; go back a few mm
G1 H1 X-465 F360        ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-465 F360        ; then move slowly to Y axis endstop
G1 X235 Y235 F6000      ; Prob at Center 
M558 F600 A1 		    ; Dive fast once 
G30			            ; probe Z
M558 F300 A10 		    ; Slow second dive with more accuracy
G30			            ; probe z again
 
 

1/31/2021, 11:51:21 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet Ethernet 1.02 or later + DueX5
Board ID: 08DLM-996RU-N8PS0-7J9D8-3S86T-1B8VP
Used output buffers: 3 of 24 (24 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 70344 of which 40 recycled
Never used RAM 18236, free system stack 210 words
Tasks: NETWORK(ready,173) HEAT(blocked,309) DUEX(blocked,35) MAIN(running,452) IDLE(ready,19)
Owned mutexes:
=== Platform ===
Last reset 00:02:05 ago, cause: power up
Last software reset at 2021-01-31 23:46, reason: User, GCodes spinning, available RAM 18236, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x04
Aux0 errors 0,0,0
MCU temperature: min 26.3, current 26.8, max 27.1
Supply voltage: min 25.0, current 25.0, max 25.1, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0, standstill, SG min/max not available
Driver 6: position 0, standstill, SG min/max not available
Driver 7: position 0, standstill, SG min/max not available
Driver 8: position 0, standstill, SG min/max not available
Driver 9: position 0, standstill, SG min/max not available
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-01-31 23:51:20
Cache data hit count 194997097
Slowest loop: 8.94ms; fastest: 0.21ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.9ms, write time 2.4ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = 3 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 25.61ms; fastest: 0.07ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 2 of 8
Interface state active, link 100Mbps full duplex
=== DueX ===
Read count 0, 0.00 reads/min
 

**The Problem now when I click HomeZ only driver number 6 moves down (!exp.e6stop) and if press any end-stop it will stop it but the rest they do not move at all this is the problem I have I don't know if the Duex5 is bad and not communicating effectively with the duet ethernet board. **

[Phaedrux]

@Phaedrux said in G32 ERROR:

M98 P"config.g" and post the results?

And just to confirm, you have all Z motors and endstops connected to the Duex?

And your duex is wired up for power/ground as shown here?

https://duet3d.dozuki.com/Wiki/Duex2_and_Duex5_Features#Section_Wiring

[moe.adams9093]

1/31/2021, 11:51:56 PM: M98 P"config.g": HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: bad grid definition: Too many grid points; suggest increase spacing to 21.0mm
Warning: Macro file config-override.g not found
 

sorry I thought I did post my M98. but everything works correctly on my duex5 except my end stops. If I run M564 S0 H0 all Zmotors work correctly. the duex5 is wired correctly as and all endstops wired correctly as well

[fcwilt]

@moe-adams9093 said in G32 ERROR:

M569 P8 S0 ; physical drive 7 goes Backwards

The comment says 7 the command specifies 8.

Have you manually activated each Z end stop sensor, one at a time, and run M119 to verify the reported end stop state?

Frederick

[moe.adams9093]

Yes I did and they all trigger as Z max endstop on m119

[moe.adams9093]

M569 P5 S1
M569 P6 S1
M569 P8 S0
M569 P9 S0
Yes this is the correct format for all of my z axis motors 2 motors are mirror to the other 2 thats why I have p8 s0 and p9 s0