DWC 3.1.1

[luca Massimiliano]

; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT+0100 (Ora standard dell’Europa centrale)

; IN GONFIG.G OK

Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT + 0100 (Central European Standard Time)

Check your config files for that line. Some where there is a file that has that line and it's missing a ; at the start to mark it as a comment.

[Phaedrux]

What are you doing when that error message shows up?

[luca Massimiliano]

HO FATTO MENU FILAMENT IN SD CARD

[luca Massimiliano]

ECCO

[luca Massimiliano]

SE TOCCO PIANO-SONDATO .CSV SI BLOCCA TUUO.

[luca Massimiliano]

This post is deleted!

[luca Massimiliano]

DA L ERRORE QUANDO ARRIVA SUL PIATTO ED ESTRAE LA SONDA HO UN BBLTouch

[Phaedrux]

Please post all your config files. config.g homeall.g homex.g homey.g homez.g homedelta.g bed.g deployprobe.g retractprobe.g

[luca Massimiliano]

@luca-Massimiliano

[Phaedrux]

Do you have a file called mesh.g in the system folder?

[luca Massimiliano]

@Phaedrux said in DWC 3.1.1:

no non ho la mesh.g G29 Esegui il file sys / mesh.g, o se quel file non viene trovato, esegui G29 S0 ho fatto cosi errore:
G29 S0
Error: Bad command: Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT+0100 (Ora standard dell’Europa centrale)...

ora confronto ifail detti da te config files. config.g homeall.g homex.g homey.g homez.g homedelta.g bed.g deployprobe.g retractprobe.g con i vecchi senza problema se non risolvo li posto ,

[luca Massimiliano]

@luca-Massimiliano said in DWC 3.1.1:

Error: Bad command: Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT+0100 (Ora standard dell’Europa centrale)...
RISOLTO
COME DICEVI TE NO ERA NASCOSTO NEL FILE DELOYPROBLE.G

[luca Massimiliano]

non penso sia correto,

[Phaedrux]

http://boim.com/DeltaUtil/CalDoc/Calibration.html

[luca Massimiliano]

VORREI USARE REPETIER HOST TRAMITE WIFI , NON SO COME FARE , MI PUOI INDIRIZZARE ?

[Phaedrux]

@luca-Massimiliano said in DWC 3.1.1:

I WOULD LIKE TO USE REPETIER HOST VIA WIFI, I DON'T KNOW HOW TO DO IT, CAN YOU ADDRESS ME?

I do not know how to use repetier host.

[luca Massimiliano]

COSA USI PER STAMPARE?

[Phaedrux]

I upload the sliced file directly from the slicer to the Duet over the network.

[droftarts]

@luca-Massimiliano You upload gcode files to the 'Jobs' screen in DWC, print from there!
See: https://duet3d.dozuki.com/Wiki/Duet_Web_Control_v2_and_v3_(DWC)_Manual#Section_Jobs

Ian

[luca Massimiliano]

@Phaedrux said in DWC 3.1.1:

I upload the sliced file directly from the slicer to the Duet over the network.

MI PERDO NELLA TERMINOLOGIA AFFETTAO ? SO CHE SI USA MA NON CAPISCO