DWC 3.1.1
-
I don't know anything about proterface or repetier. I would suggest you use DWC to interact with the printer.
-
PER ME NON E' NECESSARIO USARE QUESTE APPLICAZIONI , SOLO CHE VOLEVO FARE UNA PROVA E CON IL NOSTRO DUET NON SO ANCORA USARLO ORA MI METTERO' A STUDIARE E USERO' SOLO DUET . PER LE TRADUZIONI DISONIBILE
-
This may be your best guide for learning the Duet interface.
https://duet3d.dozuki.com/Wiki/Duet_Web_Control_v2_and_v3_(DWC)_Manual
-
This may be your best guide for learning the Duet interface.
grazie 1000
-
@luca-Massimiliano I think in your config.g you have two tools defined as T0 and T1. Maybe Repetier Server has the first tool as T1, and second tool as T2. So change your config.g so that M563 uses P1 and P2, not P0 and P1. For example:
; Tools M563 P1 D0 H1 F0 ; define tool 1 G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C M563 P2 D1 H2 F0 ; define tool 2 G10 P2 X0 Y0 Z0 ; set tool 2 axis offsets G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0CIan
-
si p0 e p1 viene riconosciuto e letta la sonda ma il comando g10 p1 \p2 devo camiarli in g10 p0 e g10 p1?
-
@luca-Massimiliano yes, change lines starting G10 P0 to G10 P1, and G10 P1 to G10 P2.
Ian
-
VORREI FARE UNA PROVA DI STAMPA IN ABS E' CORRETTO
HO UNA DIFFICOLTA' SUL FILAMENO :
CONFIG.G
HO COPIATO DAL MANUALE L ESEMPIO E COPIATO ,
M207 S0.9 R0.0 F3000 T3000 Z0.0 ; firmware retraction settings for PETG
M307 H0 A214.3 C641.7 D1.3 S1.00 V24.0 B0 ; Bed PID tune for 120c
M307 H1 A491.0 C190.9 D2.8 S1.00 V23.9 B0 ; Hot end PID tune at 280c
M566 X1200 Y1200 Z60 E3000 ; jerk settings for PETG
M204 P1000 T4000
Carica macro,:
M291 P"Please wait while the nozzle is being heated up" R"Loading ABS" T5 ; Display message
G10 S200 ; Set current tool temperature to 200C
M116 ; Wait for the temperatures to be reached
M291 P"Feeding filament..." R"Loading ABS" T5 ; Display new message
M83 ; Extruder to relative mode
G1 E10 F600 ; Feed 10mm of filament at 600mm/min
G1 E470 F3000 ; Feed 470mm of filament at 3000mm/min
G1 E20 F300 ; Feed 20mm of filament at 300mm/min
G4 P1000 ; Wait one second
G1 E-10 F1800 ; Retract 10mm of filament at 1800mm/min
M400 ; Wait for moves to complete
M292 ; Hide the message
G10 S0 ; Turn off the heater again
SCARICARE macro,:
M291 P"Please wait while the nozzle is being heated up" R"Unloading ABS" T5 ; Display message
G10 S100 ; Heat up the current tool to 100C
M116 ; Wait for the temperatures to be reached
M291 P"Retracting filament..." R"Unloading ABS" T5 ; Display another message
G1 E-20 F300 ; Retract 20mm of filament at 300mm/min
G1 E-480 F3000 ; Retract 480mm of filament at 3000mm/min
M400 ; Wait for the moves to finish
M292 ; Hide the message again
M84 E0:1 ; Turn off extruder drives 1 and 2HO COPIATO DAL MANUALE L ESEMPIO E COPIATO ,
-
This post is deleted! -
-
This post is deleted! -
https://duet3d.dozuki.com/Wiki/Duet_Web_Control_v2_and_v3_(DWC)_Manual#Section_Jobs
The JOBS tab on the left side bar will show you all the gcode files.
-
E' PARTITA SPERIAMO
-
MI POTRESTI CONSIGLIARE QUALE web camera USARE ACQUISTARE PER ABBINARE ALLA STAMPENTE ?
-
There are many webcams to choose from. The important thing is that the cam can output a image URL rather than just a video feed.
I use a Raspberry Pi Zero W and a Pi cam module with MotionOS.
-
ciao Phaedrux ho ventola una e ventola 2 correttamente sulla scheda , comportamento da me chiesto al raggiungimento a 100 gradi del riscaldatore on . comportamento : ventola 1 al raggiungere 100 ok ventola 2 sempre on ecco config g riguardante
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4388 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M308 S2 P"e1temp" Y"thermistor" T100000 B4388 ; configure sensor 2 as thermistor on pin e1temp
M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H2 S280 ; set temperature limit for heater 2 to 280C; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H1 T100 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H2 T100 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 S"1" D0 H1 F-1 ; define tool 1
G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C
M563 P1 S"2" D0 H2 F-1 ; define tool 2
G10 P2 X0 Y0 Z0 ; set tool 2 axis offsets
G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0C -
@luca-Massimiliano said in DWC 3.1.1:
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H1 T100 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H2 T100 ; set fan 1 value. Thermostatic control is turned onFan1 and Fan2 or do you mean Fan0 and Fan1?
-
Fan1 and Fan2 or do you mean Fan0 and Fan1?
ho capito ,hai ragione diventa :
; Fans
M950 F2 C"fan2" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P2 S2 H2 T100 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T100 ; set fan 1 value. Thermostatic control is turned on -
io ho una delta kossel piano cerchio e diverse x y dove posso modificare il dvwc per avere una rappresentazione realistica? graze -
This post is deleted!
