Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Software package 3.3beta3 released

    Scheduled Pinned Locked Moved
    Beta Firmware
    34
    96
    10.9k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • dc42undefined
      dc42 administrators @OwenD
      last edited by

      @owend said in Software package 3.3beta3 released:

      Can you expand on what problems were being experienced using the 1 second timing?
      Whilst it is simple to run a loop within daemon.g it would be counter productive if the consequences are dire.
      Also does the 10 second count begin when daemon.g starts or finishes?
      Running a loop only makes sense if the former applies.
      Presumably, in either circumstance, daemon.g can only be run once. i.e. if it's open, then it's skipped until the next cycle.
      I have nothing currently in use that would suffer drastically from a 10 second cycle, but others may have.

      We had some evidence suggesting that the overhead of opening (or trying to open) the daemon.g file every second might be causing print slowdown and quality issues when printing a long sequence of very short moves, because of contention for the SD card. Increasing the delay to 10 seconds reduces this overhead by 90%.

      The first time that RRF tries to open daemon.g, the delay before trying to open it is one second as before so that daemon.g starts up quickly if it exists. Subsequent times (after failing to open daemon.g, or daemon.g finishing executing), the delay is ten seconds.

      I have it in mind to add a new M-code to start/stop execution of daemon.g instead.

      Duet WiFi hardware designer and firmware engineer
      Please do not ask me for Duet support via PM or email, use the forum
      http://www.escher3d.com, https://miscsolutions.wordpress.com

      Luke'sLaboratoryundefined 1 Reply Last reply Reply Quote 0
      • o_lampeundefined
        o_lampe @OwenD
        last edited by

        @owend said in Software package 3.3beta3 released:

        to reduce the load on the SD card

        Why don't we load daemon.g into memory and start it from there? That way the SD-card would only read once.
        In earlier posts, @dc42 mentioned there's plenty of RAM available on all Duet boards....

        dc42undefined 1 Reply Last reply Reply Quote 0
        • dc42undefined
          dc42 administrators @o_lampe
          last edited by

          @o_lampe said in Software package 3.3beta3 released:

          In earlier posts, @dc42 mentioned there's plenty of RAM available on all Duet boards....

          There is plenty of RAM available on the MB6HC and a reasonable margin on the Duet 3 Mini. RAM is already tight on Duet 2.

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • oc_geekundefined
            oc_geek @dc42
            last edited by oc_geek

            @dc42 i've updated to this rel (printer was off for long time) and i started to receive a rain of warnings and motors making clicking noises continuosly... powered off and powered on ...for the moment those seem gone.... what is that ??! everything is cool and at ambient temp....

            80f569b6-a98c-47e5-b9c3-f5a0384115b3-image.png

            Argoundefined 1 Reply Last reply Reply Quote 0
            • Argoundefined
              Argo @oc_geek
              last edited by

              @oc_geek

              How long was it off? I mean from which firmware did you upgrade to 3.3 beta 3?

              oc_geekundefined 1 Reply Last reply Reply Quote 1
              • oc_geekundefined
                oc_geek @Argo
                last edited by

                @argo was not asking you... 3H+ and update was from 3.3Beta2+

                dc42undefined 1 Reply Last reply Reply Quote -1
                • dc42undefined
                  dc42 administrators @oc_geek
                  last edited by

                  @oc_geek, @Argo asked the right questions and saved me having to ask them.

                  I suspect you had a bad connection in the ribbon cable between the Duet and DueX.

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  oc_geekundefined Topherundefined 2 Replies Last reply Reply Quote 0
                  • oc_geekundefined
                    oc_geek @dc42
                    last edited by oc_geek

                    @dc42 Duex ? Ribbon cable ? LOL

                    I'm on a Mini 5+ / 2+ ....
                    Actually the Third one as i had to replace them multiple times due to SD card soldering issues....

                    I'm saying i had no issue before....I install the fw after printer is completely cold at warm temperature
                    and those (nonsense) alarms came up..
                    and the steppers started clicking endless like everyting is going to break apart..

                    Take it or leave it...

                    TBH i really have enough of the attitudes of yours of all the time i ave spent around this hw and i pretend answers from yourself
                    not from experts popping up from nowere pretending to become Duet developers overnight (sorry no offence Argo...) i'm really fed up at this point

                    out

                    dc42undefined 1 Reply Last reply Reply Quote -1
                    • dc42undefined
                      dc42 administrators @oc_geek
                      last edited by

                      @oc_geek, please remain calm and polite, that's a condition of using this forum.

                      You didn't say which board you were using in your original post, so I made the incorrect assumption that it was a Due + DueX as it had more than 5 stepper drivers.

                      If that error only occurred immediately after you upgraded, and was cleared by powering off and on again, then it probably means that the TMC2209 drivers didn't immediately adapt to the change in baud rate between firmware 3.3beta2 and 3.3beta3.

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      oc_geekundefined 1 Reply Last reply Reply Quote 1
                      • oc_geekundefined
                        oc_geek @dc42
                        last edited by oc_geek

                        @dc42 ...it's becoming harder to...

                        I had posted numerous times in the other thread about layers shifts and mesh issues so i assumed you remembered the config i had, but i understand you deal with 100s issues at day...so sorry if my post was not sharp clear from start

                        Ok understand the explanation now
                        My intention was to just report factual and that the steppers really click bad and don't stop doing that...
                        Swtcing off - on appears to solve the issue.
                        Perhaps it may be worth to mention somewhere...as someone may think things are breaking apart (as i did...)

                        dc42undefined 1 Reply Last reply Reply Quote -1
                        • dc42undefined
                          dc42 administrators @oc_geek
                          last edited by dc42

                          @oc_geek, I'll mention it in the release notes in case anyone else experiences it. Thanks for your report.

                          Duet WiFi hardware designer and firmware engineer
                          Please do not ask me for Duet support via PM or email, use the forum
                          http://www.escher3d.com, https://miscsolutions.wordpress.com

                          1 Reply Last reply Reply Quote 0
                          • PaulHewundefined
                            PaulHew
                            last edited by

                            @dc42 said in Software package 3.3beta3 released:

                            Users of Duet + SBC can upgrade from the unstable package server.

                            Being totally new to using a SBC + Duet3, are these the correct commands to run to install this firmware?

                            If you wish to use the latest unstable DSF components, you can run the following commands instead:
                            
                            wget -q https://pkg.duet3d.com/duet3d.gpg
                            wget -q https://pkg.duet3d.com/duet3d-unstable.list
                            sudo mv duet3d.gpg /etc/apt/trusted.gpg.d/
                            sudo mv duet3d-unstable.list /etc/apt/sources.list.d/duet3d-unstable.list
                            sudo chown root:root /etc/apt/trusted.gpg.d/duet3d.gpg
                            sudo chown root:root /etc/apt/sources.list.d/duet3d-unstable.list
                            

                            TIA Paul.

                            RailCore II - Duet Mini + 1LC, Voron V0.1 - Duet Mini
                            Voron 2.4 disassembled..... Waiting for the RailCore Mini....

                            jay_s_ukundefined 1 Reply Last reply Reply Quote 1
                            • jay_s_ukundefined
                              jay_s_uk @PaulHew
                              last edited by

                              @paulhew yes, then sudo apt update && sudo apt upgrade

                              Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                              PaulHewundefined 1 Reply Last reply Reply Quote 0
                              • PaulHewundefined
                                PaulHew @jay_s_uk
                                last edited by

                                @jay_s_uk Thank you.
                                Need a button in DWC somewhere so it can be done!

                                P.

                                RailCore II - Duet Mini + 1LC, Voron V0.1 - Duet Mini
                                Voron 2.4 disassembled..... Waiting for the RailCore Mini....

                                1 Reply Last reply Reply Quote 0
                                • Luke'sLaboratoryundefined
                                  Luke'sLaboratory @dc42
                                  last edited by Luke'sLaboratory

                                  @dc42

                                  We had some evidence suggesting that the overhead of opening (or trying to open) the daemon.g file every second might be causing print slowdown and quality issues when printing a long sequence of very short moves, because of contention for the SD card. Increasing the delay to 10 seconds reduces this overhead by 90%.

                                  That's some interesting context

                                  I hate to re-ask, but were those issues also related to the notes: "A separate task is now used to finalize moves for execution" where those short, small moves were causing issues?

                                  My first print on 3.3beta3 didn't have the issues that have been plaguing me for a long while on my 6hc +3hc setup, So i was wondering what all went into the fix beyond the CAN sync issues from a few threads earlier

                                  Luke
                                  http://lukeslab.online

                                  dc42undefined 1 Reply Last reply Reply Quote 0
                                  • tristanryerparkeundefined
                                    tristanryerparke
                                    last edited by

                                    Thanks for all this great work guys, variables are already changing the game.
                                    Are macro parameters supported on Duet3+SBC?
                                    T

                                    dc42undefined 1 Reply Last reply Reply Quote 0
                                    • dc42undefined
                                      dc42 administrators @Luke'sLaboratory
                                      last edited by

                                      @luke-slaboratory said in Software package 3.3beta3 released:

                                      I hate to re-ask, but were those issues also related to the notes: "A separate task is now used to finalize moves for execution" where those short, small moves were causing issues?

                                      I made that change to facilitate additional functionality that needed to be incorporated into the Move subsystem, to remove some of the limitations in firmware 3.2 when using CAN-connected boards. I don't have any evidence that it fixed any issues, except that on the Duet 3 Mini it worked around another issue.

                                      My first print on 3.3beta3 didn't have the issues that have been plaguing me for a long while on my 6hc +3hc setup, So i was wondering what all went into the fix beyond the CAN sync issues from a few threads earlier.

                                      There have been several improvements and fixes to CAN traffic management in the 3.3beta series, including one between beta 2 and beta 3.

                                      Duet WiFi hardware designer and firmware engineer
                                      Please do not ask me for Duet support via PM or email, use the forum
                                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                                      Luke'sLaboratoryundefined 1 Reply Last reply Reply Quote 0
                                      • dc42undefined
                                        dc42 administrators @tristanryerparke
                                        last edited by dc42

                                        @tristanryerparke said in Software package 3.3beta3 released:

                                        Are macro parameters supported on Duet3+SBC?

                                        They should be, but I haven't tested them myself in SBC mode.

                                        Duet WiFi hardware designer and firmware engineer
                                        Please do not ask me for Duet support via PM or email, use the forum
                                        http://www.escher3d.com, https://miscsolutions.wordpress.com

                                        tristanryerparkeundefined 1 Reply Last reply Reply Quote 0
                                        • Luke'sLaboratoryundefined
                                          Luke'sLaboratory @dc42
                                          last edited by

                                          @dc42

                                          Fantastic, can't wait to get back to toolchanging 🙂

                                          Luke
                                          http://lukeslab.online

                                          1 Reply Last reply Reply Quote 0
                                          • 64bitundefined
                                            64bit
                                            last edited by

                                            work faster.... lol

                                            I started using RRF on a Fusion3 machine that we have in my office and I loved it. So much so that I bought a pair of D2Wifi boards for my two hobby printers. I installed one, and its been on 2.03 for the longest time, recently updated to 2.05.1
                                            My other machine was converted to Klipper. I love me some input shapers.
                                            I now have the D2Wifi boards in both of my machines and i am ABOUT to make the jump over to Klipper on both. If input shaper comes to RRF soon, I might not make that switch!

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA