WiFi Unreliable

SIam

@dessiverse this looks good so far now the Wi-Fi has a software version and now test if this problem persists

DessiVerse

@SIam, I'm trying to upload a gcode to test the speed and it seems like it keeps slowing down. So the same issue I was having previously. I'd like to note I don't have this issue in SBC mode.

Screen Shot 2021-04-28 at 1.36.34 PM.png

Screen Shot 2021-04-28 at 1.36.59 PM.png

EDIT: It now slowed down to 1.8 KIB/s. Here is the current M122:

Send: M122
Recv: === Diagnostics ===
Recv: RepRapFirmware for Duet 3 Mini 5+ version 3.3beta3 (2021-04-22 13:48:16) running on Duet 3 Mini5plus WiFi (standalone mode)
Recv: Board ID: 7HDQX-V296U-D65J0-40KM8-MK03Z-R91J2
Recv: Used output buffers: 2 of 40 (17 max)
Recv: === RTOS ===
Recv: Static ram: 101772
Recv: Dynamic ram: 106336 of which 12 recycled
Recv: Never used RAM 35584, free system stack 146 words
Recv: Tasks: NETWORK(ready,15.8%,150) HEAT(delaying,0.0%,318) Move(notifyWait,0.1%,188) CanReceiv(notifyWait,0.0%,943) CanSender(notifyWait,0.0%,371) CanClock(delaying,0.0%,341) TMC(notifyWait,0.7%,115) MAIN(running,82.6%,372) IDLE(ready,0.0%,19) AIN(delaying,0.8%,273), total 100.0%
Recv: Owned mutexes: WiFi(NETWORK) USB(MAIN)
Recv: === Platform ===
Recv: Last reset 00:08:20 ago, cause: power up
Recv: Last software reset at 2021-04-28 12:14, reason: HardFault bfarValid precise, GCodes spinning, available RAM 35584, slot 2
Recv: Software reset code 0x0063 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x00000803 BFAR 0x00000044 SP 0x200036a8 Task MAIN Freestk 771 ok
Recv: Stack: 00000000 2000374c 00000571 00000000 00000000 0007be25 000836d8 610f0200 2001d580 00000000 00000000 00088e39 00000000 00000000 00000000 ffffffff 369dc3a0 2001d580 20002a40 2001d37c 20003730 200037d8 200037d6 00088f33 00000001 200202e8 200180d8
Recv: Error status: 0x00
Recv: Aux0 errors 0,0,0
Recv: Aux1 errors 0,0,0
Recv: MCU revision 3, ADC conversions started 501054, completed 501052, timed out 0, errs 0
Recv: Step timer max interval 1489
Recv: MCU temperature: min 29.7, current 32.8, max 32.8
Recv: Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
Recv: Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Recv: Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 19090, writes 0, timeouts 0, DMA errors 0
Recv: Driver 1: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 19090, writes 0, timeouts 0, DMA errors 0
Recv: Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 19091, writes 0, timeouts 0, DMA errors 0
Recv: Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 19090, writes 0, timeouts 0, DMA errors 0
Recv: Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 19090, writes 0, timeouts 0, DMA errors 0
Recv: Driver 5: position 0, assumed not present
Recv: Driver 6: position 0, assumed not present
Recv: Date/time: 2021-04-28 13:38:55
Recv: Cache data hit count 1012800891
Recv: Slowest loop: 12.17ms; fastest: 0.12ms
Recv: === Storage ===
Recv: Free file entries: 9
Recv: SD card 0 detected, interface speed: 22.5MBytes/sec
Recv: SD card longest read time 4.2ms, write time 3.9ms, max retries 0
Recv: === Move ===
Recv: DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
Recv: === MainDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === AuxDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === Heat ===
Recv: Bed heaters = 0 -1, chamberHeaters = -1 -1
Recv: === GCodes ===
Recv: Segments left: 0
Recv: Movement lock held by null
Recv: HTTP is idle in state(s) 0
Recv: Telnet is idle in state(s) 0
Recv: File is idle in state(s) 0
Recv: USB is ready with "M122" in state(s) 0
Recv: Aux is idle in state(s) 0
Recv: Trigger is idle in state(s) 0
Recv: Queue is idle in state(s) 0
Recv: LCD is idle in state(s) 0
Recv: SBC is idle in state(s) 0
Recv: Daemon is idle in state(s) 0
Recv: Aux2 is idle in state(s) 0
Recv: Autopause is idle in state(s) 0
Recv: Code queue is empty.
Recv: === CAN ===
Recv: Messages queued 3265, send timeouts 3265, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17)
Recv: Last cancelled message type 30 dest 127
Recv: === Network ===
Recv: Slowest loop: 200.02ms; fastest: 0.06ms
Recv: Responder states: HTTP(3) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
Recv: HTTP sessions: 1 of 8
Recv: - WiFi -
Recv: Network state is active
Recv: WiFi module is connected to access point
Recv: Failed messages: pending 0, notready 0, noresp 1
Recv: WiFi firmware version 1.26
Recv: WiFi MAC address f0:08:d1:02:ec:f2
Recv: WiFi Vcc 3.33, reset reason Power up
Recv: WiFi flash size 2097152, free heap 20640
Recv: WiFi IP address 10.0.0.201
Recv: WiFi signal strength -36dBm, mode 802.11n, reconnections 0, sleep mode modem
Recv: Clock register 00002002
Recv: Socket states: 0 2 0 0 0 0 0 0
Recv: ok
Send: M105
Recv: ok T:20.1 /0.0 T0:20.1 /0.0 B:22.5 /0.0

jay_s_uk

@dessiverse what sd card are you using? Brand and model?

DessiVerse

@jay_s_uk san disk edge, 8gb

DessiVerse

@jay_s_uk I just tried using my SanDisk Extreme Pro to see if it was an issue with that and it doesn't seem to be the case. I use that micro sd with my high fps camera so read and writes are never an issue.

jay_s_uk

@dessiverse the 8gb one appears to only be a class 4. A class 10 may be better. I suggest trying another as card if you have one.

jay_s_uk

@dessiverse what speeds were you seeing with the extreme?

DessiVerse

@jay_s_uk Screen Shot 2021-04-28 at 2.55.24 PM.png
same as before, and dropping since i took that screenshot. it's now down to 6 KIB/s.

jay_s_uk

@dessiverse can you grab an M122 output while its uploading with the slower speed?

DessiVerse

@jay_s_uk

Send: M122
Recv: === Diagnostics ===
Recv: RepRapFirmware for Duet 3 Mini 5+ version 3.3beta3 (2021-04-22 13:48:16) running on Duet 3 Mini5plus WiFi (standalone mode)
Recv: Board ID: 7HDQX-V296U-D65J0-40KM8-MK03Z-R91J2
Recv: Used output buffers: 1 of 40 (17 max)
Recv: === RTOS ===
Recv: Static ram: 101772
Recv: Dynamic ram: 106336 of which 12 recycled
Recv: Never used RAM 35584, free system stack 154 words
Recv: Tasks: NETWORK(ready,14.8%,221) HEAT(delaying,0.0%,318) Move(notifyWait,0.1%,188) CanReceiv(notifyWait,0.0%,943) CanSender(notifyWait,0.0%,371) CanClock(delaying,0.0%,341) TMC(notifyWait,0.7%,115) MAIN(running,83.6%,374) IDLE(ready,0.0%,19) AIN(delaying,0.8%,273), total 100.0%
Recv: Owned mutexes: WiFi(NETWORK) USB(MAIN)
Recv: === Platform ===
Recv: Last reset 00:04:46 ago, cause: power up
Recv: Last software reset at 2021-04-28 12:14, reason: HardFault bfarValid precise, GCodes spinning, available RAM 35584, slot 2
Recv: Software reset code 0x0063 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x00000803 BFAR 0x00000044 SP 0x200036a8 Task MAIN Freestk 771 ok
Recv: Stack: 00000000 2000374c 00000571 00000000 00000000 0007be25 000836d8 610f0200 2001d580 00000000 00000000 00088e39 00000000 00000000 00000000 ffffffff 369dc3a0 2001d580 20002a40 2001d37c 20003730 200037d8 200037d6 00088f33 00000001 200202e8 200180d8
Recv: Error status: 0x00
Recv: Aux0 errors 0,0,0
Recv: Aux1 errors 0,0,0
Recv: MCU revision 3, ADC conversions started 286329, completed 286328, timed out 0, errs 0
Recv: Step timer max interval 752
Recv: MCU temperature: min 26.6, current 30.6, max 30.6
Recv: Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
Recv: Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Recv: Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 10585, writes 0, timeouts 0, DMA errors 0
Recv: Driver 1: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 10585, writes 0, timeouts 0, DMA errors 0
Recv: Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 10585, writes 0, timeouts 0, DMA errors 0
Recv: Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 10585, writes 0, timeouts 0, DMA errors 0
Recv: Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 10585, writes 0, timeouts 0, DMA errors 0
Recv: Driver 5: position 0, assumed not present
Recv: Driver 6: position 0, assumed not present
Recv: Date/time: 2021-04-28 14:54:39
Recv: Cache data hit count 551034519
Recv: Slowest loop: 4.92ms; fastest: 0.12ms
Recv: === Storage ===
Recv: Free file entries: 10
Recv: SD card 0 detected, interface speed: 22.5MBytes/sec
Recv: SD card longest read time 0.7ms, write time 0.0ms, max retries 0
Recv: === Move ===
Recv: DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
Recv: === MainDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === AuxDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === Heat ===
Recv: Bed heaters = 0 -1, chamberHeaters = -1 -1
Recv: Heater 1 is on, I-accum = 0.0
Recv: === GCodes ===
Recv: Segments left: 0
Recv: Movement lock held by null
Recv: HTTP is idle in state(s) 0
Recv: Telnet is idle in state(s) 0
Recv: File is idle in state(s) 0
Recv: USB is ready with "M122" in state(s) 0
Recv: Aux is idle in state(s) 0
Recv: Trigger is idle in state(s) 0
Recv: Queue is idle in state(s) 0
Recv: LCD is idle in state(s) 0
Recv: SBC is idle in state(s) 0
Recv: Daemon is idle in state(s) 0
Recv: Aux2 is idle in state(s) 0
Recv: Autopause is idle in state(s) 0
Recv: Code queue is empty.
Recv: === CAN ===
Recv: Messages queued 1810, send timeouts 1810, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17)
Recv: Last cancelled message type 4514 dest 127
Recv: === Network ===
Recv: Slowest loop: 200.87ms; fastest: 0.00ms
Recv: Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
Recv: HTTP sessions: 1 of 8
Recv: - WiFi -
Recv: Network state is active
Recv: WiFi module is connected to access point
Recv: Failed messages: pending 0, notready 0, noresp 1
Recv: WiFi firmware version 1.26
Recv: WiFi MAC address f0:08:d1:02:ec:f2
Recv: WiFi Vcc 3.33, reset reason Power up
Recv: WiFi flash size 2097152, free heap 20976
Recv: WiFi IP address 10.0.0.201
Recv: WiFi signal strength -37dBm, mode 802.11n, reconnections 0, sleep mode modem
Recv: Clock register 00002002
Recv: Socket states: 0 0 0 0 0 0 0 0
Recv: ok

jay_s_uk

Maybe one for one of the duet team to comment on?
@Phaedrux

DessiVerse

@jay_s_uk I'm not sure. I am kind of running out of patience with this though if I'm being honest. I was running it in SBC mode for a while because of the speeds, but, I can't use Octoprint with that so I can't use a camera ¯_(ツ)_/¯

jay_s_uk

@dessiverse you know you can run things like motion with the SBC setup for camera usage.
We have some info here https://teamgloomy.github.io/camera.html

DessiVerse

@jay_s_uk I wouldn’t be able to run monitoring software like spaghetti detective though. So I wanted to try to get just the duet working so I can plug my pi into it for octopi. But, I still would need to access the duet panel now and then if I wanna edit any of the files.

jay_s_uk

@dessiverse there are also some features of the firmware that are only available when printing from the sd card (i.e. not streamed from octoprint).
You can see them here https://duet3d.dozuki.com/Wiki/Firmware_Overview?revisionid=HEAD#Section_Printing_over_USB_connection_Octoprint_Cura_Simplify3D_Etc

DessiVerse

@jay_s_uk I'm aware of those. I normally print on the SD Card over Octoprint anyway, but I can't communicate with the sdcard using Octoprint with this board. Which is back to why I need WiFi working so I can upload to the SD card via the duet dashboard.

DessiVerse

SBC mode is no longer working. I assume that's due to the beta firmware that was installed. Can someone please help with this? My printer is now entirely unusable.

Screen Shot 2021-04-28 at 6.07.15 PM.png

Phaedrux

To use the beta firmware on the duet and SBC mode the SBC would need to be updated to the beta as well.

So either return the Duet back to 3.2.2 to match the version installed on the pi, or add the unstable repository to the pi and then update again.

See here for more details on adding the unstable branch.
https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Software_Installation

Phaedrux

As for the slow wifi speeds it's a bit perplexing as the signal strength seems good and the SD card should be fine.

I notice you mentioned you have some pis in close proximity on wifi that work ok. Does powering off those pis have any improvement? Perhaps interference?

DessiVerse

@phaedrux I’ve tried that with no luck. I’ve also tried in other areas with no luck as well