WiFi Unreliable

[DessiVerse]

@siam I updated the firmware and confirmed the update.
Console is still getting spammed with the below messages:

Recv: WiFi reported error: network scan failed
Recv: WiFi module is idle
Recv: WiFi reported error: network scan failed
Recv: WiFi module is idle
Recv: WiFi reported error: network scan failed
Recv: WiFi module is idle
Recv: WiFi reported error: network scan failed
Recv: WiFi module is idle
Recv: WiFi reported error: network scan failed

Here is the result of M122

Send: M122
Recv: === Diagnostics ===
Recv: RepRapFirmware for Duet 3 Mini 5+ version 3.3beta3 (2021-04-22 13:48:16) running on Duet 3 Mini5plus WiFi (standalone mode)
Recv: Board ID: 7HDQX-V296U-D65J0-40KM8-MK03Z-R91J2
Recv: Used output buffers: 1 of 40 (1 max)
Recv: === RTOS ===
Recv: Static ram: 101772
Recv: Dynamic ram: 106336 of which 12 recycled
Recv: Never used RAM 35584, free system stack 160 words
Recv: Tasks: NETWORK(ready,8.0%,346) HEAT(delaying,0.0%,318) Move(notifyWait,0.1%,188) CanReceiv(notifyWait,0.0%,943) CanSender(notifyWait,0.0%,371) CanClock(notifyWait,0.0%,341) TMC(notifyWait,0.7%,115) MAIN(running,90.1%,426) IDLE(ready,0.3%,19) AIN(delaying,0.8%,273), total 100.0%
Recv: Owned mutexes: USB(MAIN)
Recv: === Platform ===
Recv: Last reset 00:01:10 ago, cause: software
Recv: Last software reset at 2021-04-28 12:14, reason: HardFault bfarValid precise, GCodes spinning, available RAM 35584, slot 2
Recv: Software reset code 0x0063 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x00000803 BFAR 0x00000044 SP 0x200036a8 Task MAIN Freestk 771 ok
Recv: Stack: 00000000 2000374c 00000571 00000000 00000000 0007be25 000836d8 610f0200 2001d580 00000000 00000000 00088e39 00000000 00000000 00000000 ffffffff 369dc3a0 2001d580 20002a40 2001d37c 20003730 200037d8 200037d6 00088f33 00000001 200202e8 200180d8
Recv: Error status: 0x00
Recv: Aux0 errors 0,0,0
Recv: Aux1 errors 0,0,0
Recv: MCU revision 3, ADC conversions started 70672, completed 70672, timed out 0, errs 0
Recv: Step timer max interval 745
Recv: MCU temperature: min 29.2, current 30.6, max 30.6
Recv: Supply voltage: min 23.9, current 23.9, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
Recv: Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Recv: Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 20, reads 3696, writes 9, timeouts 0, DMA errors 0
Recv: Driver 1: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 20, reads 3696, writes 9, timeouts 0, DMA errors 0
Recv: Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 19, reads 3696, writes 9, timeouts 0, DMA errors 0
Recv: Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 19, reads 3696, writes 9, timeouts 0, DMA errors 0
Recv: Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 19, reads 3696, writes 9, timeouts 0, DMA errors 0
Recv: Driver 5: position 0, assumed not present
Recv: Driver 6: position 0, assumed not present
Recv: Date/time: 1970-01-01 00:00:00
Recv: Cache data hit count 146022799
Recv: Slowest loop: 25.74ms; fastest: 0.12ms
Recv: === Storage ===
Recv: Free file entries: 10
Recv: SD card 0 detected, interface speed: 22.5MBytes/sec
Recv: SD card longest read time 3.2ms, write time 0.0ms, max retries 0
Recv: === Move ===
Recv: DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
Recv: === MainDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === AuxDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === Heat ===
Recv: Bed heaters = 0 -1, chamberHeaters = -1 -1
Recv: Heater 1 is on, I-accum = 0.0
Recv: === GCodes ===
Recv: Segments left: 0
Recv: Movement lock held by null
Recv: HTTP is idle in state(s) 0
Recv: Telnet is idle in state(s) 0
Recv: File is idle in state(s) 0
Recv: USB is ready with "M122" in state(s) 0
Recv: Aux is idle in state(s) 0
Recv: Trigger is idle in state(s) 0
Recv: Queue is idle in state(s) 0
Recv: LCD is idle in state(s) 0
Recv: SBC is idle in state(s) 0
Recv: Daemon is idle in state(s) 0
Recv: Aux2 is idle in state(s) 0
Recv: Autopause is idle in state(s) 0
Recv: Code queue is empty.
Recv: === CAN ===
Recv: Messages queued 635, send timeouts 633, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17)
Recv: Last cancelled message type 4514 dest 127
Recv: === Network ===
Recv: Slowest loop: 199.80ms; fastest: 0.00ms
Recv: Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
Recv: HTTP sessions: 0 of 8
Recv: - WiFi -
Recv: Network state is disabled
Recv: WiFi module is disabled
Recv: Failed messages: pending 0, notready 0, noresp 2
Recv: Socket states: 0 0 0 0 0 0 0 0

I started running the typical commands to try to get it to reconnect and got an error

Send: M552 S-1
Recv: ok
Send: M552
Recv: WiFi module is disabled
Recv: ok
Send: M105
Recv: ok T:19.8 /0.0 T0:19.8 /0.0 B:22.5 /0.0
Send: M552 S0
Recv: ok
Recv: WiFi module started
Send: M552 S1
Recv: ok
Send: M105
Recv: ok T:19.8 /0.0 T0:19.8 /0.0 B:22.5 /0.0
Recv: WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to

After spamming the "network scan failed" messages I got ran M552 to see the status and got Recv: WiFi module is connected to access point , IP address 255.255.255.255

[SIam]

@dessiverse have you updated the DuetWiFiServer.bin ?

[DessiVerse]

@siam I’ve been trying to but it keeps saying the file doesn’t exist even though it’s in the sys directory.

[DessiVerse]

@siam

[jay_s_uk]

@dessiverse it needs to be in a folder called firmware with 3.3 rather than in the sys folder

[DessiVerse]

@jay_s_uk just got it installed. Doesn't appear to be improved though.

[DessiVerse]

Here's an updated M122

Send: M122
Recv: === Diagnostics ===
Recv: RepRapFirmware for Duet 3 Mini 5+ version 3.3beta3 (2021-04-22 13:48:16) running on Duet 3 Mini5plus WiFi (standalone mode)
Recv: Board ID: 7HDQX-V296U-D65J0-40KM8-MK03Z-R91J2
Recv: Used output buffers: 1 of 40 (11 max)
Recv: === RTOS ===
Recv: Static ram: 101772
Recv: Dynamic ram: 106336 of which 12 recycled
Recv: Never used RAM 35584, free system stack 157 words
Recv: Tasks: NETWORK(ready,19.8%,150) HEAT(delaying,0.0%,318) Move(notifyWait,0.1%,188) CanReceiv(notifyWait,0.0%,943) CanSender(notifyWait,0.0%,371) CanClock(notifyWait,0.0%,341) TMC(notifyWait,0.7%,115) MAIN(running,78.2%,426) IDLE(ready,0.4%,19) AIN(delaying,0.8%,273), total 100.0%
Recv: Owned mutexes: USB(MAIN)
Recv: === Platform ===
Recv: Last reset 00:02:18 ago, cause: power up
Recv: Last software reset at 2021-04-28 12:14, reason: HardFault bfarValid precise, GCodes spinning, available RAM 35584, slot 2
Recv: Software reset code 0x0063 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x00000803 BFAR 0x00000044 SP 0x200036a8 Task MAIN Freestk 771 ok
Recv: Stack: 00000000 2000374c 00000571 00000000 00000000 0007be25 000836d8 610f0200 2001d580 00000000 00000000 00088e39 00000000 00000000 00000000 ffffffff 369dc3a0 2001d580 20002a40 2001d37c 20003730 200037d8 200037d6 00088f33 00000001 200202e8 200180d8
Recv: Error status: 0x00
Recv: Aux0 errors 0,0,0
Recv: Aux1 errors 0,0,0
Recv: MCU revision 3, ADC conversions started 138334, completed 138334, timed out 0, errs 0
Recv: Step timer max interval 1490
Recv: MCU temperature: min 23.8, current 29.7, max 29.7
Recv: Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
Recv: Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Recv: Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 7247, writes 10, timeouts 0, DMA errors 0
Recv: Driver 1: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 7247, writes 10, timeouts 0, DMA errors 0
Recv: Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 7247, writes 9, timeouts 0, DMA errors 0
Recv: Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 7247, writes 9, timeouts 0, DMA errors 0
Recv: Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 7248, writes 9, timeouts 0, DMA errors 0
Recv: Driver 5: position 0, assumed not present
Recv: Driver 6: position 0, assumed not present
Recv: Date/time: 2021-04-28 13:32:52
Recv: Cache data hit count 320404896
Recv: Slowest loop: 1051.41ms; fastest: 0.12ms
Recv: === Storage ===
Recv: Free file entries: 9
Recv: SD card 0 detected, interface speed: 22.5MBytes/sec
Recv: SD card longest read time 3.9ms, write time 0.0ms, max retries 0
Recv: === Move ===
Recv: DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
Recv: === MainDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === AuxDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === Heat ===
Recv: Bed heaters = 0 -1, chamberHeaters = -1 -1
Recv: === GCodes ===
Recv: Segments left: 0
Recv: Movement lock held by null
Recv: HTTP is idle in state(s) 0
Recv: Telnet is idle in state(s) 0
Recv: File is idle in state(s) 0
Recv: USB is ready with "M122" in state(s) 0
Recv: Aux is idle in state(s) 0
Recv: Trigger is idle in state(s) 0
Recv: Queue is idle in state(s) 0
Recv: LCD is idle in state(s) 0
Recv: SBC is idle in state(s) 0
Recv: Daemon is idle in state(s) 0
Recv: Aux2 is idle in state(s) 0
Recv: Autopause is idle in state(s) 0
Recv: Code queue is empty.
Recv: === CAN ===
Recv: Messages queued 1244, send timeouts 1241, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 16)
Recv: Last cancelled message type 4514 dest 127
Recv: === Network ===
Recv: Slowest loop: 1993.74ms; fastest: 0.00ms
Recv: Responder states: HTTP(0) HTTP(2) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
Recv: HTTP sessions: 1 of 8
Recv: - WiFi -
Recv: Network state is active
Recv: WiFi module is connected to access point
Recv: Failed messages: pending 0, notready 0, noresp 0
Recv: WiFi firmware version 1.26
Recv: WiFi MAC address f0:08:d1:02:ec:f2
Recv: WiFi Vcc 3.33, reset reason Power up
Recv: WiFi flash size 2097152, free heap 14336
Recv: WiFi IP address 10.0.0.201
Recv: WiFi signal strength -37dBm, mode 802.11n, reconnections 0, sleep mode modem
Recv: Clock register 00002002
Recv: Socket states: 0 2 0 0 0 0 0 0
Recv: ok

[SIam]

@dessiverse this looks good so far now the Wi-Fi has a software version and now test if this problem persists

[DessiVerse]

@SIam, I'm trying to upload a gcode to test the speed and it seems like it keeps slowing down. So the same issue I was having previously. I'd like to note I don't have this issue in SBC mode.

EDIT: It now slowed down to 1.8 KIB/s. Here is the current M122:

Send: M122
Recv: === Diagnostics ===
Recv: RepRapFirmware for Duet 3 Mini 5+ version 3.3beta3 (2021-04-22 13:48:16) running on Duet 3 Mini5plus WiFi (standalone mode)
Recv: Board ID: 7HDQX-V296U-D65J0-40KM8-MK03Z-R91J2
Recv: Used output buffers: 2 of 40 (17 max)
Recv: === RTOS ===
Recv: Static ram: 101772
Recv: Dynamic ram: 106336 of which 12 recycled
Recv: Never used RAM 35584, free system stack 146 words
Recv: Tasks: NETWORK(ready,15.8%,150) HEAT(delaying,0.0%,318) Move(notifyWait,0.1%,188) CanReceiv(notifyWait,0.0%,943) CanSender(notifyWait,0.0%,371) CanClock(delaying,0.0%,341) TMC(notifyWait,0.7%,115) MAIN(running,82.6%,372) IDLE(ready,0.0%,19) AIN(delaying,0.8%,273), total 100.0%
Recv: Owned mutexes: WiFi(NETWORK) USB(MAIN)
Recv: === Platform ===
Recv: Last reset 00:08:20 ago, cause: power up
Recv: Last software reset at 2021-04-28 12:14, reason: HardFault bfarValid precise, GCodes spinning, available RAM 35584, slot 2
Recv: Software reset code 0x0063 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x00000803 BFAR 0x00000044 SP 0x200036a8 Task MAIN Freestk 771 ok
Recv: Stack: 00000000 2000374c 00000571 00000000 00000000 0007be25 000836d8 610f0200 2001d580 00000000 00000000 00088e39 00000000 00000000 00000000 ffffffff 369dc3a0 2001d580 20002a40 2001d37c 20003730 200037d8 200037d6 00088f33 00000001 200202e8 200180d8
Recv: Error status: 0x00
Recv: Aux0 errors 0,0,0
Recv: Aux1 errors 0,0,0
Recv: MCU revision 3, ADC conversions started 501054, completed 501052, timed out 0, errs 0
Recv: Step timer max interval 1489
Recv: MCU temperature: min 29.7, current 32.8, max 32.8
Recv: Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
Recv: Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Recv: Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 19090, writes 0, timeouts 0, DMA errors 0
Recv: Driver 1: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 19090, writes 0, timeouts 0, DMA errors 0
Recv: Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 19091, writes 0, timeouts 0, DMA errors 0
Recv: Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 19090, writes 0, timeouts 0, DMA errors 0
Recv: Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 19090, writes 0, timeouts 0, DMA errors 0
Recv: Driver 5: position 0, assumed not present
Recv: Driver 6: position 0, assumed not present
Recv: Date/time: 2021-04-28 13:38:55
Recv: Cache data hit count 1012800891
Recv: Slowest loop: 12.17ms; fastest: 0.12ms
Recv: === Storage ===
Recv: Free file entries: 9
Recv: SD card 0 detected, interface speed: 22.5MBytes/sec
Recv: SD card longest read time 4.2ms, write time 3.9ms, max retries 0
Recv: === Move ===
Recv: DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
Recv: === MainDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === AuxDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === Heat ===
Recv: Bed heaters = 0 -1, chamberHeaters = -1 -1
Recv: === GCodes ===
Recv: Segments left: 0
Recv: Movement lock held by null
Recv: HTTP is idle in state(s) 0
Recv: Telnet is idle in state(s) 0
Recv: File is idle in state(s) 0
Recv: USB is ready with "M122" in state(s) 0
Recv: Aux is idle in state(s) 0
Recv: Trigger is idle in state(s) 0
Recv: Queue is idle in state(s) 0
Recv: LCD is idle in state(s) 0
Recv: SBC is idle in state(s) 0
Recv: Daemon is idle in state(s) 0
Recv: Aux2 is idle in state(s) 0
Recv: Autopause is idle in state(s) 0
Recv: Code queue is empty.
Recv: === CAN ===
Recv: Messages queued 3265, send timeouts 3265, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17)
Recv: Last cancelled message type 30 dest 127
Recv: === Network ===
Recv: Slowest loop: 200.02ms; fastest: 0.06ms
Recv: Responder states: HTTP(3) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
Recv: HTTP sessions: 1 of 8
Recv: - WiFi -
Recv: Network state is active
Recv: WiFi module is connected to access point
Recv: Failed messages: pending 0, notready 0, noresp 1
Recv: WiFi firmware version 1.26
Recv: WiFi MAC address f0:08:d1:02:ec:f2
Recv: WiFi Vcc 3.33, reset reason Power up
Recv: WiFi flash size 2097152, free heap 20640
Recv: WiFi IP address 10.0.0.201
Recv: WiFi signal strength -36dBm, mode 802.11n, reconnections 0, sleep mode modem
Recv: Clock register 00002002
Recv: Socket states: 0 2 0 0 0 0 0 0
Recv: ok
Send: M105
Recv: ok T:20.1 /0.0 T0:20.1 /0.0 B:22.5 /0.0

[jay_s_uk]

@dessiverse what sd card are you using? Brand and model?

[DessiVerse]

@jay_s_uk san disk edge, 8gb

[DessiVerse]

@jay_s_uk I just tried using my SanDisk Extreme Pro to see if it was an issue with that and it doesn't seem to be the case. I use that micro sd with my high fps camera so read and writes are never an issue.

[jay_s_uk]

@dessiverse the 8gb one appears to only be a class 4. A class 10 may be better. I suggest trying another as card if you have one.

[jay_s_uk]

@dessiverse what speeds were you seeing with the extreme?

[DessiVerse]

@jay_s_uk
same as before, and dropping since i took that screenshot. it's now down to 6 KIB/s.

[jay_s_uk]

@dessiverse can you grab an M122 output while its uploading with the slower speed?

[DessiVerse]

@jay_s_uk

Send: M122
Recv: === Diagnostics ===
Recv: RepRapFirmware for Duet 3 Mini 5+ version 3.3beta3 (2021-04-22 13:48:16) running on Duet 3 Mini5plus WiFi (standalone mode)
Recv: Board ID: 7HDQX-V296U-D65J0-40KM8-MK03Z-R91J2
Recv: Used output buffers: 1 of 40 (17 max)
Recv: === RTOS ===
Recv: Static ram: 101772
Recv: Dynamic ram: 106336 of which 12 recycled
Recv: Never used RAM 35584, free system stack 154 words
Recv: Tasks: NETWORK(ready,14.8%,221) HEAT(delaying,0.0%,318) Move(notifyWait,0.1%,188) CanReceiv(notifyWait,0.0%,943) CanSender(notifyWait,0.0%,371) CanClock(delaying,0.0%,341) TMC(notifyWait,0.7%,115) MAIN(running,83.6%,374) IDLE(ready,0.0%,19) AIN(delaying,0.8%,273), total 100.0%
Recv: Owned mutexes: WiFi(NETWORK) USB(MAIN)
Recv: === Platform ===
Recv: Last reset 00:04:46 ago, cause: power up
Recv: Last software reset at 2021-04-28 12:14, reason: HardFault bfarValid precise, GCodes spinning, available RAM 35584, slot 2
Recv: Software reset code 0x0063 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x00000803 BFAR 0x00000044 SP 0x200036a8 Task MAIN Freestk 771 ok
Recv: Stack: 00000000 2000374c 00000571 00000000 00000000 0007be25 000836d8 610f0200 2001d580 00000000 00000000 00088e39 00000000 00000000 00000000 ffffffff 369dc3a0 2001d580 20002a40 2001d37c 20003730 200037d8 200037d6 00088f33 00000001 200202e8 200180d8
Recv: Error status: 0x00
Recv: Aux0 errors 0,0,0
Recv: Aux1 errors 0,0,0
Recv: MCU revision 3, ADC conversions started 286329, completed 286328, timed out 0, errs 0
Recv: Step timer max interval 752
Recv: MCU temperature: min 26.6, current 30.6, max 30.6
Recv: Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
Recv: Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Recv: Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 10585, writes 0, timeouts 0, DMA errors 0
Recv: Driver 1: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 10585, writes 0, timeouts 0, DMA errors 0
Recv: Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 10585, writes 0, timeouts 0, DMA errors 0
Recv: Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 10585, writes 0, timeouts 0, DMA errors 0
Recv: Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 10585, writes 0, timeouts 0, DMA errors 0
Recv: Driver 5: position 0, assumed not present
Recv: Driver 6: position 0, assumed not present
Recv: Date/time: 2021-04-28 14:54:39
Recv: Cache data hit count 551034519
Recv: Slowest loop: 4.92ms; fastest: 0.12ms
Recv: === Storage ===
Recv: Free file entries: 10
Recv: SD card 0 detected, interface speed: 22.5MBytes/sec
Recv: SD card longest read time 0.7ms, write time 0.0ms, max retries 0
Recv: === Move ===
Recv: DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
Recv: === MainDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === AuxDDARing ===
Recv: Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
Recv: === Heat ===
Recv: Bed heaters = 0 -1, chamberHeaters = -1 -1
Recv: Heater 1 is on, I-accum = 0.0
Recv: === GCodes ===
Recv: Segments left: 0
Recv: Movement lock held by null
Recv: HTTP is idle in state(s) 0
Recv: Telnet is idle in state(s) 0
Recv: File is idle in state(s) 0
Recv: USB is ready with "M122" in state(s) 0
Recv: Aux is idle in state(s) 0
Recv: Trigger is idle in state(s) 0
Recv: Queue is idle in state(s) 0
Recv: LCD is idle in state(s) 0
Recv: SBC is idle in state(s) 0
Recv: Daemon is idle in state(s) 0
Recv: Aux2 is idle in state(s) 0
Recv: Autopause is idle in state(s) 0
Recv: Code queue is empty.
Recv: === CAN ===
Recv: Messages queued 1810, send timeouts 1810, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17)
Recv: Last cancelled message type 4514 dest 127
Recv: === Network ===
Recv: Slowest loop: 200.87ms; fastest: 0.00ms
Recv: Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
Recv: HTTP sessions: 1 of 8
Recv: - WiFi -
Recv: Network state is active
Recv: WiFi module is connected to access point
Recv: Failed messages: pending 0, notready 0, noresp 1
Recv: WiFi firmware version 1.26
Recv: WiFi MAC address f0:08:d1:02:ec:f2
Recv: WiFi Vcc 3.33, reset reason Power up
Recv: WiFi flash size 2097152, free heap 20976
Recv: WiFi IP address 10.0.0.201
Recv: WiFi signal strength -37dBm, mode 802.11n, reconnections 0, sleep mode modem
Recv: Clock register 00002002
Recv: Socket states: 0 0 0 0 0 0 0 0
Recv: ok

[jay_s_uk]

Maybe one for one of the duet team to comment on?
@Phaedrux

[DessiVerse]

@jay_s_uk I'm not sure. I am kind of running out of patience with this though if I'm being honest. I was running it in SBC mode for a while because of the speeds, but, I can't use Octoprint with that so I can't use a camera ¯_(ツ)_/¯

[jay_s_uk]

@dessiverse you know you can run things like motion with the SBC setup for camera usage.
We have some info here https://teamgloomy.github.io/camera.html