Duet 3 + Tool Board Extruder/Retraction Issue

Phaedrux

@evomotors said in Duet 3 + Tool Board Extruder/Retraction Issue:

hiccups 7539

So you are getting a lot of hiccups on the tool board, so perhaps try the new beta?

is 7mm/s correct for your retraction speed?

evomotors

@Phaedrux said in Duet 3 + Tool Board Extruder/Retraction Issue:

@evomotors said in Duet 3 + Tool Board Extruder/Retraction Issue:

hiccups 7539

So you are getting a lot of hiccups on the tool board, so perhaps try the new beta?

is 7mm/s correct for your retraction speed?

Retraction speed is 7 mm/s, any value higher that that was performing extremely worst when stepper connected to the tool board.

I didn't install beta yet. I'm willing to do so, but a little confused in the instructions for installing unstable version using SBC and DWC.

What about bunch of blocked and suspended CAN bus commands on the Duet3 board itself?:
CanReceiv(suspended,3388) CanSender(suspended,1392) CanClock(blocked,1436)

dc42

@evomotors said in Duet 3 + Tool Board Extruder/Retraction Issue:

What about bunch of blocked and suspended CAN bus commands on the Duet3 board itself?:
CanReceiv(suspended,3388) CanSender(suspended,1392) CanClock(blocked,1436)

Those do not refer to messages. The clue is the "Tasks:" label at the start of the line.

evomotors

@dc42 said in Duet 3 + Tool Board Extruder/Retraction Issue:

@evomotors said in Duet 3 + Tool Board Extruder/Retraction Issue:

What about bunch of blocked and suspended CAN bus commands on the Duet3 board itself?:
CanReceiv(suspended,3388) CanSender(suspended,1392) CanClock(blocked,1436)

Those do not refer to messages. The clue is the "Tasks:" label at the start of the line.

Can you please point me to how to update to latest beta? What files do I need to download update DWC (looks like it's required for new beta) what bin files do I need to update Duet3 and tool board?

I'm looking at this guide right now:
https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Updating_Duet_3_from_RRF3_0_Beta_12_to_3_0_Final_via_DWC

Phaedrux

@evomotors said in Duet 3 + Tool Board Extruder/Retraction Issue:

I'm looking at this guide right now:
https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Updating_Duet_3_from_RRF3_0_Beta_12_to_3_0_Final_via_DWC

This is for a specific case for updating to 3.0 final from 3.0 beta 12.

To update to the 3.2 beta2 using a SBC you can add the unstable repository on the pi and then use sudo apt update sudo apt upgrade as usual.

https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Software_Installation

User3D

@evomotors
Do you still face the same issue in extrusion ?
I'm planning to drive extruder from other board too.

Phaedrux

@user3d I believe all tool board extrusion issues are solved in recent firmware, though the firmware version must match between mainboard and toolboard.

User3D

@phaedrux said in Duet 3 + Tool Board Extruder/Retraction Issue:

@user3d I believe all tool board extrusion issues are solved in recent firmware, though the firmware version must match between mainboard and toolboard.

Not toolboard. I'm planning so with EXP1XD
@phaedrux is it recommended?

dc42

@user3d I am not aware of any issues using a EXP1XD to drive an extruder. The EXP1XD and the TOOL1LC use common source code, so the issues we fixed for the tool board are also fixed for the EXP1XD.

User3D

@dc42 ok. Thank you