Error: Probe was not triggered during probing move

milan.baca

@phaedrux yes I change it to
M350 X16 Y16 Z16:16:16 E16 I1

I change it back to Z16 and now

M98 P"config.g"
Warning: M307: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
Warning: M307: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 516C

milan.baca

@phaedrux
I removed G92 Z0 from homeall.g

but still same error

Phaedrux

Reduce your dive height from M558 H15 to H5

milan.baca

@phaedrux not helped, Error: This kinematics does not support auto-calibration is still there

dc42

@milan-baca I think you must have made another change to config.g. Please post it as it is now.

milan.baca

@dc42 config.g

jay_s_uk

easier to read

; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Apr 04 2021 22:18:55 GMT+0200 (CEST)

; General preferences
G90                                                  ; send absolute coordinates...
M83                                                  ; ...but relative extruder moves
M550 P"Duet 3"                                       ; set printer name
M669 K1                                              ; select CoreXY mode
M912 S-13.7										     ; mcu temperature correction

; Drives
M569 P0.0 S0 ;H50 V50 D3                             ; physical drive 0.0 goes forwards axis X
M569 P0.1 S0 ;H50 V50 D3                             ; physical drive 0.1 goes forwards axis Y
M569 P0.2 S0                                         ; physical drive 0.2 goes forwards EXTRUDER
M569 P0.3 S0 ;H50 V50 D3                             ; physical drive 0.3 goes forwards
M569 P0.4 S0 ;H50 V50 D3                             ; physical drive 0.3 goes forwards
M569 P0.5 S0 ;H50 V50 D3                             ; physical drive 0.3 goes forwards
M584 X0.0 Y0.1 Z0.3:0.4:0.5 E0.2                     ; set drive mapping
M671 X-26,188:155,021:331,23 Y-20,717:307,493:-20,717 S50 ;Z Lift Point position

M350 X16 Y16 Z16 E16 I1                        	 	 ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z1600.00 E712.00                 ; set steps per mm
M566 X1200.00 Y1200.00 Z30.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z1800.00 E1200.00           ; set maximum speeds (mm/min)
M201 X1600.00 Y1600.00 Z100.00 E250.00               ; set accelerations (mm/s^2)
M906 X1400 Y1400 Z1400 E300 I30                      ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                              ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                     ; set axis minima
M208 X320 Y320 Z321 S0                               ; set axis maxima

; Endstops
M574 X1 S1 P"io0.in"                                 ; configure active-high endstop for low end on X via pin io0.in
M574 Y1 S1 P"io1.in"                                 ; configure active-high endstop for low end on Y via pin io1.in

; Z-Probe
M950 S0 C"io7.out"                                   ; create servo pin 0 for BLTouch
M558 P9 C"io7.in" H15 F150 T6000 R0.2 A5
G31 P25 X22.775 Y5.21 Z2.5                           ; set Z probe trigger value, offset and trigger height
M557 X25:282 Y10:282 P5:5                            ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4267         ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                   ; create bed heater output on out0 and map it to sensor 0
M307 H0 B1 S1.00                                     ; enable bang-bang mode for the bed heater and set PWM limit

M140 H0                                              ; map heated bed to heater 0
M143 H0 S120                                         ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"thermistor" T100000 B3950         ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1                                   ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 R3.678 C133.6 D6.67 S1.00 V24.0
M143 H1 S280                                         ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"out7" ;Q250                                 ; create fan 0 on pin out7 and set its frequency
M106 P0 S0 H1 T45                                    ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"out4" Q500                                 ; create fan 1 on pin out4 and set its frequency
M106 P1 S1 H-1                                    	 ; set fan 1 value. Thermostatic control is turned of

; Tools
M563 P0 D0 H1 F0                                     ; define tool 0
G10 P0 X0 Y0 Z0                                      ; set tool 0 axis offsets
G10 P0 R0 S0                                         ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

;M581 Y S1 T2
; Miscellaneous
M308 S10 Y"mcu-temp" A"MCU"

M501
M911 S22 R23.5 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0

Your M671 doesn't look valid to me
how is your bed supported? what are the co-ordinates of the screws?

dc42

I agree with @jay_s_uk. Change the commas in the M671 command to fullstops.

milan.baca

@jay_s_uk
I am using calculator from this project
https://miragec79.github.io/HevORT/firmwaresettings.html

milan.baca

@dc42 thank you very much guys problem was in M671 command in numbers

I look at it many times but after you point to that command I saw the problem. It was decimal separator in coordinates

milan.baca

@dc42
G32 command now work well

still have a problem with G29
after few points I got
Error: Probe already triggered before probing move started

ps: should I make a new thread or can I continue here?

dc42

@milan-baca does it do that at the same probe point each time, or at different points?

In this line:

M558 P9 C"io7.in" H15 F150 T6000 R0.2 A5

you could try increasing R0.2 to R0.3. If that doesn't fix it then I suspect that the pin of the BLTouch may be sticky. Is it a genuine BLTouch, or a clone?

milan.baca

@dc42 triangle lab (not genuine) - but this one I am using on my other printer (I took it from there) with duet2 wifi for years and it works well there

dc42

@milan-baca you could also try reducing the maximum Z speed in M203, in case the Z axis can't keep up with the commanded speed when the probe is raised.

milan.baca

@dc42 thank you very much again R0.3 was the trick