Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Correction of heightmap is not really working

    Scheduled Pinned Locked Moved
    General Discussion
    5
    126
    6.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • fcwiltundefined
      fcwilt @ICY_SNAKE
      last edited by

      @icy_snake said in Correction of heightmap is not really working:

      @fcwilt said in Correction of heightmap is not really working:

      al config.g file you posted?

      I did not copy the hole file, now you have the full config.g file

      Understood.

      So refresh my memory - what is working, what is not working?

      Frederick

      Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

      ICY_SNAKEundefined 1 Reply Last reply Reply Quote 0
      • ICY_SNAKEundefined
        ICY_SNAKE @fcwilt
        last edited by

        @fcwilt Hello frederick,

        we need to do it tommorow, because need to leave now home.

        But i got an message the the axis are not homed because of z

        error in macro line 8

        I think its not ready somehow the distance from z

        DO IT OR DON'T

        fcwiltundefined 1 Reply Last reply Reply Quote 0
        • fcwiltundefined
          fcwilt @ICY_SNAKE
          last edited by

          @icy_snake

          I'm will be ready to work about 9:00 Eastern Standard Time.

          Frederick

          Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

          ICY_SNAKEundefined 1 Reply Last reply Reply Quote 1
          • ICY_SNAKEundefined
            ICY_SNAKE @fcwilt
            last edited by ICY_SNAKE

            @fcwilt Good morning frederick,

            back to my calibration problem.

            I run now the button on the display for leveling.

            head moves to all 4 corners and than to the middle and stays there.

            messages:

            <G32
            Leadscrew adjustments made: 0.040 0.051 0.023 0.047, points used 4, (mean, deviation) before (0.039, 0.007) after (0.000, 0.000)>
            

            if i do g28 than

            i get the following error message:

            <G28
             Error: in file macro line 8: G30: Z probe 0 not found>
            

            If i hit the button HOME ALL

            i get the following error message:

            <Error: in file macro line 7: G30: Z probe 0 not found
             Error: Homing failed
             Error: in file macro line 8: G30: Z probe 0 not found>
            

            my homeall.g

            <M280 P0 S60 I1
             G91                    			; relative positioning
             G1 H2 Z5 F200          			; lift Z relative to current position
            G1 H1 X-605 Y605 F3000 			; move quickly to X and Y axis endstops and stop there (first pass)
            G1 H2 X5 Y-5 F600      			; go back a few mm
            G1 H1 X-605 Y605 F600  			; move slowly to X and Y axis endstops once more (second pass)
            G90                    			; absolute positioning
            G30                    			; home Z by probing the bed>
            

            Dieter

            DO IT OR DON'T

            fcwiltundefined 1 Reply Last reply Reply Quote 0
            • fcwiltundefined
              fcwilt @ICY_SNAKE
              last edited by fcwilt

              @icy_snake

              Hi,

              Please post you current files:

              • config.g
              • config_probe.g
              • bed.g

              In your homeall.g file you are not moving to the center of the bed before doing the G30 to home. That is not the cause of the error messages but it should be added.

              Frederick

              Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

              ICY_SNAKEundefined 1 Reply Last reply Reply Quote 0
              • ICY_SNAKEundefined
                ICY_SNAKE @fcwilt
                last edited by ICY_SNAKE

                @fcwilt hello frederick,

                here are my files:

                config.g

                <; General preferences_________________________________________________________
                G90                                             			; send absolute coordinates...
                M83                                             			; ...but relative extruder moves
                M111 S0 													; Debug off
                M555 P2 													; Set output to look like Marlin
                M575 P0 B57600 S2               							; communication parameters for USB serial
                M575 P1 B57600 S1											; Set auxiliary serial port baud rate and require checksum (for PanelDue)
                
                ; Network_____________________________________________________________________
                M550 P"Big 60X V3.4 15.02.2022"                        		; set printer name
                ; History
                ; removed U  15.02.2022
                ;
                ;
                
                M552 S1                                        				; enable network
                M552 P192.168.10.169										; My IP Address
                M586 P0 S1                                      			; enable HTTP
                M586 P1 S0                                      			; disable FTP
                M586 P2 S0                                      			; disable Telnet
                
                ; add probe file
                ; global.g_probe_z_trigger
                ; global.g_probe_z_trigger = 2.915 ; default - set as appropriate for the Z probe 
                
                M98 P"config_probe.g"
                M556 S50 X0 Y0 Z0		                               		; set orthogonal axis compensation parameters woher kommt der test wie wurde der Winkel bestimmt Unklar!
                M376 H10													; stop z-leveling after 10 layers
                
                
                
                ; Drives_________________________________________________________________________
                ;Main board______________________________________________________________________
                M569 P0 S1                                                     		; Physical drive 0 . X1
                M569 P1 S0                                                       	; Physical drive 1 . X2
                M569 P2 R-1                                                        	; Physical drive 2 . Canceled
                M569 P3 S1                                                       	; Physical drive 3 . Main Extruder
                M569 P4 S0                                                       	; Physical drive 4 . Secondary Extruder
                ;Duex5 board_____________________________________________________________________
                M569 P5 S0                                                       	; Physical drive 5 . Y
                M569 P6 S0                                                       	; Physical drive 6 . Z1 (0,1000) 
                M569 P7 S0                                                       	; Physical drive 7 . Z2 (0,0) 
                M569 P8 S0                                                       	; Physical drive 8 . Z3 (1000,0) 
                M569 P9 S0                                          ; Physical drive 9 . Z4 (1000,1000) 
                
                ;Settings_________________________________________________________
                M584 X0:1 Y5 Z6:7:8:9 E3:4 P3						; Driver mapping
                ; M671 X-189:-189:645:645 Y645:-64:-64:645 S10  		; Anticlockwise old
                ; M671 X-168:-168:655:655 Y655:-64:-64:655 S10  		; Anticlockwise 
                M671 X-168:-168:645:645 Y645:-64:-64:645 S10 ; Anticlockwise
                
                ;___________________________________________________________________
                M350 X16 Y16 I1  		                           		; Configure microstepping with interpolation
                M350 Z16 E16:16 I0              		               	; Configure microstepping without interpolation
                
                M92 X100.00 Y100.00 Z1969.60 E416.21:416.21 	      	; Set steps per mm changed to fit my values 100mm messen und eintragen
                
                M566 X240 Y360 Z30.00 E120.00:120.00 P1          		; Set maximum instantaneous speed changes (mm/min)
                M203 X9000.00 Y9000.00 Z200.00 E1200.00:1200.00    		; Set maximum speeds (mm/min)
                M201 X1000 Y1000 Z120.00 E250.00:250.00             	; Set accelerations (mm/s^2)
                M204 P500                                      			; Set print and travel accelerations  (mm/s^2)
                M906 X1800 Y1800.00 E1000.00:1000.00 I40 				; Set motor currents (mA) and motor idle factor in per cent
                M906 Z1800.00 I50 										; Set motor currents (mA) and motor idle factor in per cent
                M84 S100 X Y E0 E1                                		; Set idle timeout - one minute
                
                ; Axis Limits
                M208 X0 Y0 Z-1 S1                               		; set axis minima
                M208 X600 Y600 Z630 S0                          		; my print area, changed to hight 630 do changes
                
                ; Endstops
                M574 X1 S1 P"xstop + e0stop"                            ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
                M574 Y2 S1 P"ystop"                            			; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
                
                		                					; Height (mm) over which to taper off the bed compensation 10, 30
                
                ; Heaters___________________________________________________________
                M140 H-1                                       			; disable heated bed (overrides default heater mapping)
                
                ;E0_________________________________________________________________
                M308 S0 P"spi.cs1" Y"rtd-max31865"
                M950 H0 C"e0heat" T0                            		; create nozzle heater output on e0heat and map it to sensor 0
                M307 H0 B0 R3.818 C129.1:116.6 D3.00 S1.00 V23.9		;New TAKOTO mit Wärmeleitpaste
                M143 H0 S300                                 			; set temperature limit for heater 0 to 300°
                
                ;E1_________________________________________________________________
                M308 S1 P"spi.cs2" Y"rtd-max31865"
                M950 H1 C"e1heat" T1                            		; create nozzle heater output on e1heat and map it to sensor 1
                M307 H1 B0 R3.746 C151.8:132.3 D3.63 S1.00 V23.9		; NEW TAKOTO
                M143 H1 S300         	                        		; set temperature limit for heater 1 to 300°
                
                
                ; Fans______________________________________________________________
                M950 F0 C"fan0" Q500                            		; create fan 0 on pin fan0 and set its frequency
                M106 P0 S0 H-1                                  		; set fan 0 value. Thermostatic control is turned on
                M950 F1 C"fan1" Q500                            		; create fan 1 on pin fan1 and set its frequency
                M106 P1 S0 H-1                                  		; set fan 1 value. Thermostatic control is turned on
                M950 F2 C"duex.fan7" Q500                            	; create LED on pin fan2 and set its frequency
                M106 P2 S0 H-1                               			; Disable fan channel for LED
                M950 F3 C"duex.fan5" Q500                       		; create fan 3 on pin fan1 and set its frequency
                M106 P3 S255 H0 T45                             		; set fan 3 value. Thermostatic control is turned on
                M950 F4 C"duex.fan6" Q500                       		; create fan 4 on pin fan1 and set its frequency
                M106 P4 S255 H1 T45                             		; set fan 4 value. Thermostatic control is turned on
                
                
                ; Tools______________________________________________________________
                ;T0_________________________________________________________________
                M563 P0 S"E0 Primary" D0 H0 F0                  		; define tool 0
                G10 P0 X0 Y0 Z0                                 		; set tool 0 axis offsets
                G10 P0 R0 S210                                  		; set initial tool 0 active and standby temperatures to 0C
                
                ;T1_________________________________________________________________
                M563 P1 S"E1 Secondary" D1 H1 F1                		; define tool 1
                G10 P1 X0 Y49 Z0                                		; set tool 1 axis offsets
                G10 P1 R0 S210                                    		; set initial tool 1 active and standby temperatures to 0C
                
                ; Automatic power saving____________________________________________
                M911 S22.5 R29.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"  ; Set voltage thresholds and actions to run on power loss. Power Failure Pause
                	
                
                ; Custom settings__________________________________________________
                M950 J0 C"exp.e2stop"  					  				; create Input Pin 0 on pin E2 to for M581 Command.
                M581 T1 P0 S0 R1										; Regular filament sensor for E0 As External Trigger
                
                M950 J1 C"exp.e3stop"  					  				; create Input Pin 1 on pin E3 to for M581 Command.
                M581 T1 P1 S0 R1										; Regular filament sensor for E1 As External Trigger
                
                M950 J2 C"exp.e4stop"  					  				; create Input Pin 2 on pin E4 to for M581 Command.>
                

                Here is my config_Probe.g

                <; probe_config.g
                ; config the probe and call the other files.g
                ;
                
                M950 S0 C"duex.pwm5"
                M558 P9 C"zprobe.in" H5 F120 T6000 A5 R0.7
                
                ; G31 P500 X-18 Y24 Z{global.g_probe_z_trigger} ; set Z probe trigger value, offset and trigger height (larger value is closer) 
                ; change to zvalue global.g_probe_z_trigger did not work 
                G31 P500 X-25 Y37 Z2.915 ; set Z probe trigger value, offset and trigger height (larger value is closer) 
                >
                

                Here is my bed.g

                <; bed.g
                ; called to perform automatic bed compensation via G32
                ;
                
                M98 P"config_probe.g"        ; insure probe is using most recent configuration values
                G29 S2                       ; cancel mesh bed compensation
                M290 R0 S0                   ; cancel baby stepping
                
                G90                          ; absolute moves
                G1 Z5 F99999                 ; insure Z starting position is high enough to avoid probing errors
                
                ; M671: Define positions pf manual bed levelling screws or Z leadscrews
                ; Xnn:nn:nn... list of between 2 and 4 X coordinates of the leadscrews that drive the Z axis or the bed levelling screws
                ; Ynn:nn:nn... list of between 2 and 4 Y coordinates of the leadscrews that drive the Z axis or the bed levelling screws
                ; Snn          maximum correction allowed for each leadscrew in mm (optional, default 1.0)
                ; Pnnn         pitch of the bed levelling screws (not used when bed levelling using independently-driven leadscrews). Defaults to 0.5mm which is correct for M3 bed levelling screws
                ; Fnn          fudge factor, default 1.0
                 
                
                M671 X-168:-168:645:645 Y645:-64:-64:645 S10 ; Anticlockwise
                
                ; --- level bed ---
                
                while true
                
                  ; run leveling pass
                
                  G30 P0 X10   Y40  Z-99999    ; Probe near a leadscrew
                  G30 P1 X600 Y40  Z-99999    ; Probe near a leadscrew
                  G30 P2 X600 Y620 Z-99999    ; Probe near a leadscrew
                  G30 P3 X10   Y620 Z-99999 S4 ; Probe near a leadscrew
                
                  if move.calibration.initial.deviation < 0.015
                
                    break
                
                  ; check pass limit - abort if pass limit reached
                
                  if iterations = 5
                
                    M291 P"Bed Leveling Aborted" R"Pass Limit Reached"
                    abort "Bed Leveling Aborted - Pass Limit Reached"
                
                ; --- finish up ---
                
                ; --- set Z=0 datum which can be affected by leveling ---
                
                G1 X300 Y300 ; move probe to center of bed - set values aaa and bbb as appropriate
                G30          ; do single probe which sets Z to trigger height of Z probe
                G31 >
                

                thx dieter

                DO IT OR DON'T

                fcwiltundefined 1 Reply Last reply Reply Quote 0
                • fcwiltundefined
                  fcwilt @ICY_SNAKE
                  last edited by

                  @icy_snake

                  Let's add the M98 P"config_probe.g" to your home all file right before the G30 and see if that makes a difference.

                  It shouldn't since you are calling config_probe.g in your config.g but let's make the change and test it.

                  Frederick

                  Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

                  ICY_SNAKEundefined 1 Reply Last reply Reply Quote 0
                  • ICY_SNAKEundefined
                    ICY_SNAKE @fcwilt
                    last edited by

                    @fcwilt
                    hello,

                    works,

                    1. we had a mismatch config_probe.g against probe_config.g

                    2. with the variable Z{global.g_probe_z_trigger} it´s not working

                    as soon as i add a value for z it works.

                    DO IT OR DON'T

                    fcwiltundefined 1 Reply Last reply Reply Quote 0
                    • fcwiltundefined
                      fcwilt @ICY_SNAKE
                      last edited by

                      @icy_snake said in Correction of heightmap is not really working:

                      @fcwilt
                      hello,

                      works,

                      1. we had a mismatch config_probe.g against probe_config.g

                      2. with the variable Z{global.g_probe_z_trigger} it´s not working

                      as soon as i add a value for z it works.

                      As @Phaedrux pointed out the Z trigger height should be the same regardless of which buildplate is in use.

                      But using a variable doesn't hurt if you want to be able to easily change the Z trigger height without stopping to edit a file.

                      I verified that using a variable works but it is required that the variable be created in config.g before any attempt to use it.

                      I think I recall you initially declared it after the call to config_probe.g (the file name doesn't matter - if you prefer another name just check that you use the same name everywhere.

                      Frederick

                      Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

                      Sculpt Fabricatorundefined 1 Reply Last reply Reply Quote 0
                      • Sculpt Fabricatorundefined
                        Sculpt Fabricator @fcwilt
                        last edited by

                        @fcwilt This has been great, I am having the exact same problems as @ICY_SNAKE with the same machine. V3.3, I have followed and made all the same changes.

                        But I am having a Errror: in file macro line 6 column 43: G31 : unknown
                        variable 'g_probe_z_trigger"

                        I don't understand what that is ?

                        fcwiltundefined 1 Reply Last reply Reply Quote 0
                        • fcwiltundefined
                          fcwilt @Sculpt Fabricator
                          last edited by

                          @sculpt-fabricator said in Correction of heightmap is not really working:

                          @fcwilt This has been great, I am having the exact same problems as @ICY_SNAKE with the same machine. V3.3, I have followed and made all the same changes.

                          But I am having a Errror: in file macro line 6 column 43: G31 : unknown
                          variable 'g_probe_z_trigger"

                          I don't understand what that is ?

                          Did you create the variable in your config.g file as I specified in my example?

                          Frederick

                          Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

                          Sculpt Fabricatorundefined 2 Replies Last reply Reply Quote 0
                          • Sculpt Fabricatorundefined
                            Sculpt Fabricator @fcwilt
                            last edited by

                            @fcwilt
                            Here is my Config.g

                            
                            
                            
                            ; General preferences_________________________________________________________
                            G21 														; dimentions in mm
                            G90                                             			; for X,Y,Z     use absolute coordinate values
                            M83                                             			; for E0,E1,etc use relative coordinate values
                            M111 S0 													; Debug off
                            M555 P2 													; Set output to look like Marlin
                            M575 P0 B57600 S2              								; communication parameters for USB serial
                            M575 P1 B57600 S1											; Set auxiliary serial port baud rate and require checksum (for PanelDue)
                            
                            ; Network_____________________________________________________________________
                            M550 P"Big 60"                         						; set printer name
                            M552 S1                                        				; enable (S1) networking (WiFi)
                            M586 S1 P1 ;T0                 								; enable (S1) FTP    (P1) Disable TLS (T0)
                            M586 S1 P2 ;T0                								; enable (S1) Telnet (P2) Disable TLS (T0)
                            ;;M586 P0 S1                                      			; enable HTTP
                            ;;M586 P1 S0                                      			; disable FTP
                            ;;M586 P2 S0                                      			; disable Telnet
                             
                            
                            ; mode control variables _____________________________________________________
                            
                            global g_z_home            = 5                  ; can be used to always move Z to known height
                            global g_z_datum_set       = false              ; can be used to prevent unneeded setting of Z=0 datum
                             
                            global g_map_mode          = "300 point"        ; determines which kind of height map is created/loaded
                            global g_probe_mode        = "two consecutive"  ; determines if z proving used consecutive or averaging
                            global g_level_mode        = "4 point"          ; determines if 3 or 4 points are used for leveling
                             
                            global g_print_beg_prime   = 10                 ; default - set desired in filament config.g
                            global g_print_beg_retract = 0                  ; default - set desired in filament config.g
                             
                            global g_print_end_retract = 0                  ; default - set desired in filament config.g
                            global g_print_end_mode    = "heat off"         ; determines if heaters are turned off when print is done
                             
                            
                            ; Drives_________________________________________________________________________
                            ;Main board______________________________________________________________________
                            M569 P0 S0                                                          ; Physical drive 0 . X1
                            M569 P1 S1                                                          ; Physical drive 1 . X2
                            M569 P3 S1                                                       	; Physical drive 3 . Main Extruder
                            M569 P4 S0                                                       	; Physical drive 4 . Secondary Extruder									
                            ;Duex5 board_____________________________________________________________________
                            M569 P5 S0                                                       	; Physical drive 5 . Y
                            M569 P6 S0                                                       	; Physical drive 6 . Z1 (0,0) 
                            M569 P7 S0                                                       	; Physical drive 7 . Z2 (600,0) 
                            M569 P8 S0                                                       	; Physical drive 8 . Z3 (600,600) 
                            M569 P9 S0                                                       	; Physical drive 9 . Z4 (0,600) 
                            
                            ;Settings_________________________________________________________
                            M584 X0:1 Y5 Z6:7:8:9  E3:4 P3								   	    ; Driver mapping                                                  U1
                            M671 X-189:-189:645:645 Y645:-64:-64:645 S10                        ; Anticlockwise
                            ;;M671 X-190:-190:641:641 Y-63:643:643:-63 S10    	                ; Anticlockwise 
                            ;___________________________________________________________________
                            M350 X16 Y16 I1  		                            				; Configure microstepping with interpolation                      U16
                            M350 Z16 E16:16 I0              		                			; Configure microstepping without interpolation
                            
                            M92 X100.00 Y100.00 Z2000.00 E686:700       				        ; Set steps per mm                                                U100.00
                            
                            M566 X300 Y500 Z100.00 E120.00:120.00  P1               		    ; Set maximum instantaneous speed changes (mm/min)                U240
                            M203 X18000.00 Y18000.00 Z300.00 E1200.00:1200.00           		; Set maximum speeds (mm/min)                                     U9000.00
                            M201 X1000 Y1000 Z120.00 E250.00:250.00                  			; Set accelerations (mm/s^2)                                      U1000
                            ;M566 X240 Y360 Z30.00 E120.00:120.00 U240 P1               	    ; Set maximum instantaneous speed changes (mm/min)
                            ;M203 X9000.00 Y9000.00 Z200.00 E1200.00:1200.00 U9000.00    		; Set maximum speeds (mm/min)
                            ;M201 X1000 Y1000 Z120.00 E250.00:250.00 U1000             			; Set accelerations (mm/s^2)
                            M204 P500                                     			            ; Set print and travel accelerations  (mm/s^2)
                            M906 X1800 Y1800.00 E1270:1270  I40 					        	; Set motor currents (mA) and motor idle factor in per cent (E1270 per dyze)   U1800
                            M906 Z1800.00 I50 													; Set motor currents (mA) and motor idle factor in per cent
                            M84 S100                                          					; Set idle timeout - 100 seconds
                            
                            ; Axis Limits
                            
                            M208 X0 Y0 Z-1 S1                               			 	    ; set axis minima
                            M208 X590 Y580 Z630 S0                          					; set axis maxima
                            
                            ; Endstops
                            
                            ;;M574 X1 S1 P"xstop"                            			; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
                            ;;M574 U1 S1 P"e0stop"                            			; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
                            M574 X1 S1 P"xstop + e0stop"                            	; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
                            M574 Y2 S1 P"ystop"                            				; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
                            
                            
                            ; add probe file
                            ; global.g_probe_z_trigger
                            ; global.g_probe_z_trigger = 1.9                         ; default - set as appropriate for the Z probe 
                            M558 P9 C"^zprobe.in" H5 F120 T6000 A1 R1  					; set Z probe type to bltouch and the dive height + speeds
                            M950 S0 C"duex.pwm5"										; set probe pin
                            M98 P"config_probe.g"
                            M556 S50 X0 Y0 Z0		                               		; set orthogonal axis compensation parameters woher kommt der test wie wurde der Winkel bestimmt Unklar!
                            M376 H10													; stop z-leveling after 10 layers
                             ; Z-Probe
                            ;M558 P9 C"^zprobe.in" H5 F120 T6000 A1 R1  					; set Z probe type to bltouch and the dive height + speeds
                            ;M950 S0 C"duex.pwm5"										; set probe pin
                            ;M98 P"config_probe.g"										; configure probe after a reboot or reset
                            ;global g_probe_z_trigger   = 1.8                            ; default - set as appropriate for the Z probe
                            
                            ;;G31 P500 X-30 Y0 Z2.64                 			  		; set Z probe trigger value, offset and trigger height    **** Z height change + 0.29 ****
                            ;;M556 S50 X0 Y0 Z0                               			; set orthogonal axis compensation parameters
                            ;;M557 X0:560 Y0:580 S90:108.75              			   	; define mesh grid and probe points, fine S30:36.25
                            ;;M376 H10			                						; Height (mm) over which to taper off the bed compensation
                            
                            
                            ; Heaters___________________________________________________________
                            M140 H-1                                       				; disable heated bed (overrides default heater mapping)
                            ;M308 S0  P"bedtemp" Y"thermistor" A"Bed Heat"  T100000 B3950 ; define bed temperature sensor
                            ;M950 H0  C"bedheat" T0 Q10                                      ;heater 0 uses the bed_heat pin, sensor 0, PWM 10hz
                            
                            ;E0_________________________________________________________________
                            M308 S0 P"spi.cs1" Y"rtd-max31865" A"Main Extruder"         ; create sensor number 1 as a PT100 sensor in first position daughterboard 
                            M950 H0 C"e0heat"   T0                       		        	; create nozzle heater output on e0heat and map it to sensor 0
                            M307 H0 B0 R2.004 C403.6:385.3 D14.93 S1.00 V23.8          ; PID calibration
                            M143 H0 S450                                    			; set temperature limit for heater 0 to 450C
                            
                            ;E1_________________________________________________________________
                            M308 S1 P"spi.cs2" Y"rtd-max31865" A"Support Extruder"    	; create sensor number 2 as a PT100 sensor in sec position daughterboard 
                            ;M950 H1 C"e1heat" T1                            			; create nozzle heater output on e1heat and map it to sensor 1				TEMP OFF
                            ;M307 H1 B0 S1.00                               			; PID calibration															TEMP OFF
                            ;M143 H1 S450                                   			; set temperature limit for heater 1 to 450C								TEMP OFF
                            
                            ;E4_________________________________________________________________
                            M308 S1 P"duex.e4temp" Y"thermistor" T100000 B4267   			; configure sensor 1 as thermistor on pin e1temp
                            M950 H5 C"duex.e4heat" T1                            			; create nozzle heater output on e4heat and map it to sensor 4
                            ;M307 H5 B0 S1.00                               			     ; PID calibration															
                            M143 H5 S120                                  			    ; set temperature limit for heater 1 to 120C
                            
                            ; Fans & LED___________________________________________________________
                            M950 F0 C"fan0" Q500                            			; create fan 0 on pin fan0 and set its frequency
                            M106 P0 S0 H-1                                  			; set fan 0 value. Thermostatic control is turned on
                            
                            M950 F1 C"fan1" Q500                            			; create fan 1 on pin fan1 and set its frequency
                            M106 P1 S0 H-1                                  			; set fan 1 value. Thermostatic control is turned on
                            
                            M950 F2 C"fan2" Q500                            			; create air filter fan on fan 2 on pin fan2 and set its frequency
                            M106 P2 S0 H-1                                  			; set fan 2 value. Thermostatic control is turned on
                            
                            M950 F7 C"!duex.fan7" Q500                            		; create LED on pin fan7 and set its frequency
                            M106 P7 S0 H-1                               				; Disable fan channel for LED
                            M106 P7 S255							                    ; remove ";" to set the LED to full brightness by default
                            
                            M950 F3 C"duex.fan3" Q500                       			; create fan 3 on pin fan3 and set its frequency
                            M106 P3 S1 H-1                           			; set fan 3 value. Thermostatic control is turned on Bed relay to on
                            
                            
                            
                            ; Tools______________________________________________________________
                            ;T0_________________________________________________________________
                            M563 P0 S"E0 Main" D0 H0 F0                  			; define tool 0
                            G10 P0 X0 Y0 Z0                                 			; set tool 0 axis offsets
                            G10 P0 R0 S265                                  			; set initial tool 0 active and standby temperatures to 0C
                            
                            ;T1_________________________________________________________________
                            M563 P1 S"E1 Support" D1 H1 F1                			; define tool 1
                            G10 P1 X0 Y65 Z0                                			; set tool 1 axis offsets  Y-2 moves filament 2mm to back of machine     X-1 moves filament 1mm to the right
                            G10 P1 R0 S265                                    			; set initial tool 1 active and standby temperatures to 0C
                            
                            ;T2____________________________________________________________________
                            ;M563 P2 S"BED TEMP" H-1																												;Temp off 
                            ;G10 P2 																																;Temp off 
                            
                            ;T3___________________________________________________________________
                            M563 P3 S"CHAMBER TEMP" H5
                            G10 P3 R0 S40
                            
                            ; Custom settings__________________________________________________
                            
                            M591 D0 P1 C"duex.e2stop" S1							; Regular filament sensor for E0
                            M591 D1 P1 C"duex.e3stop" S1							; Regular filament sensor for E1
                            
                            ;M950 P2 C"fan2" Q500
                            M42 P2 S255 											; Start up air filter 
                            
                            ; Automatic power saving____________________________________________
                            M911 S22.5 R29.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"              ; Set voltage thresholds and actions to run on power loss. Power Failure Pause
                            
                            
                            fcwiltundefined 1 Reply Last reply Reply Quote 0
                            • Sculpt Fabricatorundefined
                              Sculpt Fabricator @fcwilt
                              last edited by

                              @fcwilt
                              I am just not picking up this coding. I have spent 5 days straight on this.

                              Question - So when a Error pops up it is there to tell you there is a problem and to point you in the direction of the problem to fix the issue, I assume ?

                              So, when I get a -
                              Error: in file macro line 44 column 10: meta command: 'break' was not inside a loop

                              How do I know what macro, and column is the spot on line 10?

                              fcwiltundefined 1 Reply Last reply Reply Quote 0
                              • fcwiltundefined
                                fcwilt @Sculpt Fabricator
                                last edited by

                                @sculpt-fabricator

                                Amazing.

                                What are the odds you would have global variables with the exact same names as mine. 😉

                                In any case the variable mentioned in the error appears more than once in your config.g file but they are all commented out.

                                Enable the second one (the one with 1.9) by removing the comment character.

                                Also I see these two commands:

                                M558 P9 C"^zprobe.in" H5 F120 T6000 A1 R1
                                M950 S0 C"duex.pwm5"
                                

                                They should be moved to your config_probe.g file. If they are already in that file simply remove them from your config.g file.

                                Frederick

                                Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

                                1 Reply Last reply Reply Quote 1
                                • fcwiltundefined
                                  fcwilt @Sculpt Fabricator
                                  last edited by

                                  @sculpt-fabricator said in Correction of heightmap is not really working:

                                  @fcwilt
                                  I am just not picking up this coding. I have spent 5 days straight on this.

                                  Question - So when a Error pops up it is there to tell you there is a problem and to point you in the direction of the problem to fix the issue, I assume ?

                                  So, when I get a -
                                  Error: in file macro line 44 column 10: meta command: 'break' was not inside a loop

                                  How do I know what macro, and column is the spot on line 10?

                                  Well I test each macro as I code it so I know which macro is creating the error. Then since the error messages tells me what line and column I can focus in on the error.

                                  I don't move on to some other coding until the macro is error free.

                                  Do you have a bed.g file?

                                  If so post it here, please.

                                  Frederick

                                  Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

                                  Sculpt Fabricatorundefined 1 Reply Last reply Reply Quote 0
                                  • Sculpt Fabricatorundefined
                                    Sculpt Fabricator @fcwilt
                                    last edited by

                                    @fcwilt

                                    Ok so me making 100 changes at once is not good ! LOL

                                    ;M98 P"config_probe.g"        ; insure probe is using most recent configuration values
                                     
                                    G29 S2                       ; cancel mesh bed compensation
                                    M290 R0 S0                   ; cancel baby stepping
                                     
                                    G90                          ; absolute moves
                                    G1 Z5 F99999                 ; insure Z starting position is high enough to avoid probing errors
                                     
                                    ; M671: Define positions pf manual bed levelling screws or Z leadscrews
                                     
                                    ; Xnn:nn:nn... list of between 2 and 4 X coordinates of the leadscrews that drive the Z axis or the bed levelling screws
                                    ; Ynn:nn:nn... list of between 2 and 4 Y coordinates of the leadscrews that drive the Z axis or the bed levelling screws
                                    ; Snn          maximum correction allowed for each leadscrew in mm (optional, default 1.0)
                                    ; Pnnn         pitch of the bed levelling screws (not used when bed levelling using independently-driven leadscrews). Defaults to 0.5mm which is correct for M3 bed levelling screws
                                    ; Fnn          fudge factor, default 1.0
                                    
                                    M671 X-189:-189:645:645 Y645:-64:-64:645 S10 ; Anticlockwise 
                                    
                                    ; --- level bed ---
                                     
                                     while true
                                     
                                    ; run leveling pass
                                     
                                    G30 P0 X10 Y10 Z-99999      ; probe near a leadscrew
                                    G30 P1 X570 Y10 Z-99999     ; probe near a leadscrew 
                                    G30 P2 X570   Y570   Z-99999     ; probe near a leadscrew
                                    G30 P3 X10   Y570   Z-99999 S4  ; probe near a leadscrew and calibrate 4 motors 
                                     
                                       if move.calibration.initial.deviation < 0.02
                                    
                                        break
                                     
                                       ; check pass limit - abort if pass limit reached
                                     
                                       if iterations = 5
                                     
                                         M291 P"Bed Leveling Aborted" R"Pass Limit Reached"
                                         abort "Bed Leveling Aborted - Pass Limit Reached"
                                     
                                     ; --- finish up ---
                                     
                                     ; --- set Z=0 datum which can be affected by leveling ---
                                     
                                     G1 X270 Y270 ; move probe to center of bed - set values aaa and bbb as appropriate
                                     G30          ; do single probe which sets Z to trigger height of Z probe
                                    
                                    ; config_probe.g
                                    ; config the probe and call the other files.g
                                     
                                    M558 P9 C"^zprobe.in" H5 F120 T6000 A1 R1
                                    M950 S0 C"duex.pwm5"
                                    G31 P25 X-30 Y0 Z1.688 ; set Z probe trigger value, offset and trigger height (larger value is closer)G31 P500 X-18 Y24 Z2.917
                                    
                                    Sculpt Fabricatorundefined 1 Reply Last reply Reply Quote 0
                                    • Sculpt Fabricatorundefined
                                      Sculpt Fabricator @Sculpt Fabricator
                                      last edited by

                                      that is my bed.g
                                      and config_probe.g

                                      fcwiltundefined 1 Reply Last reply Reply Quote 0
                                      • fcwiltundefined
                                        fcwilt @Sculpt Fabricator
                                        last edited by

                                        @sculpt-fabricator said in Correction of heightmap is not really working:

                                        that is my bed.g
                                        and config_probe.g

                                        OK your config_probe.g file looks good. So remove the commands I mentioned from config.g

                                        Please upload your bed.g file using the "upload file" tag. I will edit it to correct the errors.

                                        You simply have not used the required indentation.

                                        Frederick

                                        Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

                                        Sculpt Fabricatorundefined 3 Replies Last reply Reply Quote 0
                                        • Sculpt Fabricatorundefined
                                          Sculpt Fabricator @fcwilt
                                          last edited by

                                          Got the lines changed in the config.g
                                          53c4553b-7416-43a3-88c3-e28bf4d94205-image.png

                                          Here is the bed.g
                                          bed.g

                                          fcwiltundefined 1 Reply Last reply Reply Quote 0
                                          • Sculpt Fabricatorundefined
                                            Sculpt Fabricator @fcwilt
                                            last edited by

                                            @fcwilt

                                            Here is homeall.g

                                            ; homeall.g
                                            ; called to home all axes
                                            
                                            G91                    					; relative positioning
                                            
                                            G1 H2 Z5 F200          		            ; lift Z relative to current position
                                            G1 H1 X-605 Y605 F3000 		            ; move quickly to X and Y axis endstops and stop there (first pass)     
                                            G1 H2 X5 Y-5 F600      		            ; go back a few mm
                                            G1 H1 X-605 Y605 F600  		            ; move slowly to X and Y axis endstops once more (second pass)           
                                                                                                  
                                            G90                    		            ; absolute positioning
                                            M98 P"config_probe.g"
                                            G30                    		            ; home Z by probing the bed
                                            G1
                                            

                                            mesh.g

                                            M98 P"config_probe.g"        ; insure probe is using most recent configuration values
                                             
                                            G29 S2                       ; cancel mesh bed compensation
                                            M290 R0 S0                   ; cancel baby stepping
                                             
                                            G90                          ; absolute moves
                                             
                                            							 ; --- set Z=0 datum which is needed for creating a heightmap
                                             
                                            G1 Z5 F99999                 ; insure Z starting position is high enough to avoid probing errors
                                             
                                            G1 X270 Y270                 ; move probe to center of bed - set values aaa and bbb as appropriate
                                            G30                          ; do single probe which sets Z to trigger height of Z probe
                                             
                                            M557 X0:560 Y0:580 S58       ; define mesh grid 420 points S58       			
                                            G28
                                            G29 S0                       ; probe bed and create height map
                                            
                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA