@icy_snake Good morning,

i connected all metal cases to ground.
Now it´s gone.

Had to get ride of paint, so that there is an electrical connection.

thx
Dieter

@icy_snake Thx Frederick

i´m from germany Augsburg. You are from the USA, located Verginia? For time offset.
east cost 6 hours i´m ahead.

@fcwilt Whowww, many thanks Frederick,

perfect support, you helped me alot, thanks again.

I´m often in the USA for business. Maybe there will be a day that we could have some drinks.

Best Regards
Dieter

@icy_snake I´m already home today, here it´s evening.

I will add tomorrow the new code. I let you know if i could get it running.

Good evening
Dieter

@fcwilt hahah yes it was and it is and will be in the future.

thx all for the perfect help here.

Dieter

@fcwilt said in Is filament chnage required?:

the filament change message you mentioned in an earlier po

yes we have the macro which gives the message but not sure why it comes up during printing.

As i wrote in an other post that there are problems with statics voltage, do bad design of the printer.

I added ground to all metall pieces, had to get ride of paint etc.

Now i can touch the dispaly or printer without any failures or messages on the display.

my feeling is the reason was the missing grounding.

I´m printig now a big part, total progress 540h . already 96h done.

Thx for your help
Dieter

@jay_s_uk

so here i will set:

 M906 X1800.00 Y1800.00 E560.00:560.00 I40 				; Set motor currents (mA) and motor idle factor in per cent

Ok yes.

Thx
Dieter

@jay_s_uk

so here i will set:

 M906 X1800.00 Y1800.00 E560.00:560.00 I40 				; Set motor currents (mA) and motor idle factor in per cent

Ok yes.

Thx
Dieter

Hello

got the new bontech LGX extruder.

The label says 5.5V and max 0.7A

Where can i set the value only for the extruder 1 and 2?

Thx
Dieter

I need some information.

After the print is ready i need to switch a relay. (the relay will turn off my extra fans, lights etc)

Can some one explain me how to do that.

Many thx
Dieter

@resam Here is a sample code
Box_2_led-rar.txt

rename to .rar

includes a 160x160 thumbnail in the gcode plus an thumbnail for octoprint and Mainsail.

Dieter

@fcwilt said in Is filament chnage required?:

the filament change message you mentioned in an earlier po

yes we have the macro which gives the message but not sure why it comes up during printing.

As i wrote in an other post that there are problems with statics voltage, do bad design of the printer.

I added ground to all metall pieces, had to get ride of paint etc.

Now i can touch the dispaly or printer without any failures or messages on the display.

my feeling is the reason was the missing grounding.

I´m printig now a big part, total progress 540h . already 96h done.

Thx for your help
Dieter

@fcwilt Here is my

pause.g

<; pause.g
; called when a print from SD card is paused
M300 S1111 P222
M117"Is filament change required? Navigate to the macros tab and press on Filament Change"
M564 H1 S1 		; 
M116
M83            		; relative extruder moves
G1 E-10 F800  		; retract 10mm of filament
G91            		; relative positioning
G1 Z20 F360     	; lift Z by 20mm
G90
G1 Y0 F6000 		; go to the front
G1 X0 F6000 		; go to the left
M300 S1111 P333
M291 R"Attention !" P"It is recommended to turn off the heaters if the pause is expected to last a long time" T46>

@phaedrux
ok here as a txt
icy_modix60_setup .txt

Hey it worked.

@fcwilt said in Is filament chnage required?:

d when you get the filament message

All tabs are empty, already checked.

@phaedrux I cannot upload a zip or rar file??

@phaedrux yes it is coming always.