Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Possible corrupt sd card, G29 Network Error

    Scheduled Pinned Locked Moved
    General Discussion
    3
    28
    1.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • jay_s_ukundefined
      jay_s_uk @Dizzwold
      last edited by

      @Dizzwold ok, format the SD card using the sd card formatter https://www.sdcard.org/downloads/formatter/sd-memory-card-formatter-for-mac-download/
      don't bother loading any files to it. just pop it in the duet and then run M39 again

      Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

      Dizzwoldundefined 1 Reply Last reply Reply Quote 0
      • Dizzwoldundefined
        Dizzwold @jay_s_uk
        last edited by Dizzwold

        @jay_s_uk

        The sd card that came with the 6HC does exactly the same. I've not touched this card until ow, so that should be Fat 32???
        Screen Shot 2022-10-27 at 09.42.53.png
        Original sd card;

        RepRapFirmware for Duet 3 MB6HC version 3.4.4
        Warning: Cannot initialise SD card 0: Card is unusable
        Ethernet is disabled.
        RepRapFirmware for Duet 3 MB6HC is up and running.
        M552
        Ethernet is disabled, configured IP address: 0.0.0.0, actual IP address: 0.0.0.0
        ok
        M552 S1 P192.168.1.70
        ok
        MEthernet running, IP address = 192.168.1.70
        552
        Ethernet is enabled, configured IP address: 192.168.1.70, actual IP address: 192.168.1.70
        ok
        M552
        Ethernet is enabled, configured IP address: 192.168.1.70, actual IP address: 192.168.1.70
        ok
        M39
        Error: M39: No SD card mounted in slot 0
        ok
        
        jay_s_ukundefined 1 Reply Last reply Reply Quote 0
        • jay_s_ukundefined
          jay_s_uk @Dizzwold
          last edited by

          @Dizzwold in which case looks like a warranty might in order
          when and where did you purchase the duet?
          hopefully @Phaedrux or maybe @droftarts will authorise

          Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

          Dizzwoldundefined 1 Reply Last reply Reply Quote 0
          • Dizzwoldundefined
            Dizzwold @jay_s_uk
            last edited by Dizzwold

            @jay_s_uk

            Originally purchased 29/1/21
            Replaced 11/2/21 as the original had a broken connector retainer.

            I was going to install the board then, but then I had to move house, so nothing has been done until September, except for opening and checking to makes sure there were no broken connectors etc.

            Just waiting for the new sd card to be formatted with the link you sent, doing an overwrite....

            jay_s_ukundefined 1 Reply Last reply Reply Quote 0
            • jay_s_ukundefined
              jay_s_uk @Dizzwold
              last edited by

              @Dizzwold see what the duet guys say then. in the mean time can you take a high res picture of the sd card socket and the pins that are soldered to the board?

              Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

              Dizzwoldundefined 1 Reply Last reply Reply Quote 0
              • Dizzwoldundefined
                Dizzwold @jay_s_uk
                last edited by

                @jay_s_uk

                Okay, just formatted the sd card with a full overwrite, Popped it in the 6HC;
                Screen Shot 2022-10-27 at 10.46.46.png

                SeqZCcSuReKFAJlvyVa+ZQ.jpg
                rsJDhZtmRfy%AnCxHUP24Q.jpg
                9ZmR92dySa2RcWyDLw1aXA.jpg
                nON7REPjSKqzf5b2NMe7jQ.jpg
                t%I657ZvT7+FT+M9eGlUTg.jpg

                jay_s_ukundefined 1 Reply Last reply Reply Quote 0
                • jay_s_ukundefined
                  jay_s_uk @Dizzwold
                  last edited by

                  @Dizzwold nothing more i can do now. There's obviously an issue with the SD card slot
                  will leave it to the duet guys

                  Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                  Dizzwoldundefined 1 Reply Last reply Reply Quote 0
                  • Dizzwoldundefined
                    Dizzwold @jay_s_uk
                    last edited by

                    @jay_s_uk

                    Seriously, a big Thank you for your help @jay_s_uk .

                    I'm really grateful for your time and guidance.

                    1 Reply Last reply Reply Quote 1
                    • Phaedruxundefined
                      Phaedrux Moderator
                      last edited by

                      Sorry to see you're still having some issues with that board. The SD slot appears to have failed. Perhaps a marginal solder joint. As you were using the SBC before, you wouldn't have noticed.

                      Please send an email to warranty@duet3d.com and CC your reseller. Include a link to this forum thread and the details of your original purchase. You'll receive a reply with a form to fill out.

                      I don't think this is related to your other issues when using the SBC, as the SD card slot on the duet is obviously unused in that setup, but perhaps there is something else weird going on with it. Regardless, this would give you a fresh start.

                      Z-Bot CoreXY Build | Thingiverse Profile

                      Dizzwoldundefined 1 Reply Last reply Reply Quote 1
                      • Dizzwoldundefined
                        Dizzwold @Phaedrux
                        last edited by

                        @jay_s_uk @Phaedrux

                        Hi Guys,

                        Well a new 6HC arrived yesterday.

                        Got things started today "getting connected" etc. This time, I'm not going to bother with a RPi.

                        Now with a blank file system and updated firmware, can I just upload my original files from the DWC Upload System Files, should I upload all of these?
                        Screen Shot 2022-11-08 at 13.09.29.png

                        jay_s_ukundefined 1 Reply Last reply Reply Quote 0
                        • jay_s_ukundefined
                          jay_s_uk @Dizzwold
                          last edited by

                          @Dizzwold I wouldn't bother with the config.json and the dwc-settings.json.
                          The rest you should be fine with

                          Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                          Dizzwoldundefined 1 Reply Last reply Reply Quote 0
                          • Dizzwoldundefined
                            Dizzwold @jay_s_uk
                            last edited by Dizzwold

                            @jay_s_uk

                            Thank you.

                            I've also just noticed something in my config.g that I thick, with looking in the dictionary ,is causing conflict. In M950 shouldn't my bed heater be H0 (H zero), rather than T0 (T zero), and my nozzle be T0 (T zero) instead of T1?

                            ; Configuration file for Duet 3 MB 6HC (firmware version 3.3)
                            ; executed by the firmware on start-up
                            ;
                            ; generated by RepRapFirmware Configuration Tool v3.3.13 on Mon Sep 19 2022 16:04:20 GMT+0100 (British Summer Time)
                            
                            ; General preferences
                            M575 P1 S1 B57600                                  ; enable support for PanelDue
                            G90                                                ; send absolute coordinates...
                            M83                                                ; ...but relative extruder moves
                            M550 P"Duet 3"                                     ; set printer name
                            M669 K1                                            ; select CoreXY mode
                            
                            ; Network
                            M552 P
                            
                            ; Bed Leadscrew Positions
                            M671 X5:278 Y146:146 P2.0						; middle left, middle right
                            
                            G4 S1												;wait for expansion boards to start
                            
                            ; Drives
                            M569 P0.0 S0                                       ; physical drive 0.0 goes backwards
                            M569 P0.1 S0                                       ; physical drive 0.1 goes backwards
                            M569 P0.2 S1                                       ; physical drive 0.2 goes forwards
                            M569 P0.3 S1
                            M569 P121.0 S0                                       ; physical drive 0.3 goes forwards
                            M584 X0.0 Y0.1 Z0.2:0.3 E121.0                           ; set drive mapping
                            M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
                            M92 X80.00 Y80.00 Z400.00 E333.40                  ; set steps per mm
                            M566 X900.00 Y900.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
                            M203 X6000.00 Y6000.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
                            M201 X500.00 Y500.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
                            M906 X900 Y900 Z900 E800 I30                       ; set motor currents (mA) and motor idle factor in per cent
                            M84 S30                                            ; Set idle timeout
                            
                            ; Axis Limits
                            M208 X-2 Y-8 Z0 S1                                 ; set axis minima
                            M208 X330 Y330 Z400 S0                             ; set axis maxima
                            
                            ; Endstops
                            M574 X1 S1 P"!121.io1.in"                              ; configure switch-type (e.g. microswitch) endstop for low end on X via pin !io1.in
                            M574 Y1 S1 P"!io2.in"                              ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin !io2.in
                            
                            
                            ; Z-Probe
                            M574 Z1 Z1 S2									   ; set endstops controlled be probe
                            M558 P8 C"^!121.io0.in" H5 F120 T6000                 ; set Z probe type to switch and the dive height + speeds
                            G31 P500 X-46 Y-19 Z2.45                            ; set Z probe trigger value, offset and trigger height
                            M557 X19:244 Y-2:304 P9                           ; define mesh grid
                            
                            ; Heaters
                            M308 S0 P"temp0" Y"thermistor" T100000 B4138       ; configure sensor 0 as thermistor on pin temp0
                            M950 H0 C"out0" T0                                 ; create bed heater output on out0 and map it to sensor 0
                            M307 H0 R0.187 K0.192:0.000 D1.89 E1.35 S1.00 B0   ; disable bang-bang mode for the bed heater and set PWM limit
                            M140 H0                                            ; map heated bed to heater 0
                            M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
                            M308 S1 P"121.temp0" Y"thermistor" T100000 B4138       ; configure sensor 1 as thermistor on pin temp1
                            M950 H1 C"121.out0" T1                                 ; create nozzle heater output on out1 and map it to sensor 1
                            M307 H1 R2.498 K0.275:0.349 D6.79 E1.35 S1.00 B0 V24.0  ; disable bang-bang mode for heater  and set PWM limit
                            M143 H1 S280                                       ; set temperature limit for heater 1 to 280C
                            
                            ; Fans
                            M950 F0 C"121.out1" Q500                               ; create fan 0 on pin out4 and set its frequency
                            M106 P0 C"Print Cooler" S0 H-1                     ; set fan 0 name and value. Thermostatic control is turned off
                            M950 F1 C"121.out2" Q500                               ; create fan 1 on pin out5 and set its frequency
                            M106 P1 C"Extruder Cooling" S1 H1 T45              ; set fan 1 name and value. Thermostatic control is turned on
                            
                            ; Tools
                            M563 P0 S"Hemera" D0 H1 F0                         ; define tool 0
                            G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
                            G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C
                            
                            ; Custom settings are not defined
                            ; Emergency Stop
                            M950 J1 C"io4.in"
                            M851 P1 T0 S0 R0
                            
                            
                            ; Miscellaneous
                            M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                            
                            T0
                            
                            M501
                            

                            Screen Shot 2022-11-09 at 15.51.43.png

                            So far so good with using the ethernet, and without fully commissioning I ran a G32 once with no problems, no running a second scan for unknown reasons and no network error.
                            Without further testing I can't say if this was linked to the previous board, found to have an sd card issue or not.

                            Sorry "I thick" , * I think.

                            Phaedruxundefined 1 Reply Last reply Reply Quote 2
                            • Phaedruxundefined
                              Phaedrux Moderator @Dizzwold
                              last edited by

                              @Dizzwold said in Possible corrupt sd card, G29 Network Error:

                              In M950 shouldn't my bed heater be H0 (H zero), rather than T0 (T zero), and my nozzle be T0 (T zero) instead of T1?

                              No.

                              T When creating a heater: temperature sensor number, required (see M308). When creating a LED strip: LED type (optional): 0 = DotStar, 1 = RGB Neopixel (default), 2 = RGBW Neopixel. DotStar LEDs can normally be assigned only to an output intended for them.

                              https://docs.duet3d.com/en/User_manual/Reference/Gcodes#m950-create-heater-fan-spindle-or-gpioservo-pin

                              Z-Bot CoreXY Build | Thingiverse Profile

                              1 Reply Last reply Reply Quote 0
                              • First post
                                Last post
                              Unless otherwise noted, all forum content is licensed under CC-BY-SA