• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Changed ISP

Scheduled Pinned Locked Moved
General Discussion
5
25
813
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    Dizzwold
    last edited by 25 Feb 2023, 16:35

    Hi Guys,

    I had my Duet3 6HC running on my network with a fixed IP address.

    I've just change ISP to Now Broadband and can't locate my Duet on my network.

    Is this an issue with the Now Broadband router, as I've found issues with port forwarding with Home Assistant?

    Dizzwold.

    undefined 1 Reply Last reply 25 Feb 2023, 17:19 Reply Quote 0
    • undefined
      Exerqtor @Dizzwold
      last edited by Exerqtor 25 Feb 2023, 17:19

      @Dizzwold

      If your ISP gave you a new modem/router combo that you switched too chances are that all your static IP devices are borked. And only the ones with DHCP enabled still work because many ISP's have a "non-standard" IP range and/or subnet configured on their routers.

      For instance your old ISP used "standard IP" range 192.168.0.x and your static ip devices are set to something within that range.

      Then your new ISP's router might have a "non-standard" IP range 192.168.10.x, then all your devices with a static IP won't be able to "connect". The solution being to either change the ip range of your new router to be the same as your old. Or conform all static ip devices to the new IP range.

      undefined 1 Reply Last reply 25 Feb 2023, 18:07 Reply Quote 0
      • undefined
        Dizzwold @Exerqtor
        last edited by 25 Feb 2023, 18:07

        @Exerqtor

        I've gone into my routers setting;
        LAN TCP/IP Setup and changed "use router a DHCP Server" and changed the start IP address and ending IP address, so my duets static ip address is within these ranges, but still nothing?

        undefined 1 Reply Last reply 25 Feb 2023, 19:40 Reply Quote 0
        • undefined
          markz @Dizzwold
          last edited by markz 25 Feb 2023, 19:40

          @Dizzwold Generally you don't want a static address between start and end or your router might assign it to a different device dynamically. So, use the same subnet but start after or before the static address.

          So, my router uses 192.168.0.xxx subnet and I reserve the <100 folks for static addresses and the >100 for dynamic. I let it deliver 192.168.0.100-192.168.0.250 dynamically.

          undefined 1 Reply Last reply 25 Feb 2023, 20:08 Reply Quote 0
          • undefined
            Dizzwold @markz
            last edited by 25 Feb 2023, 20:08

            @markz

            Okay, I've put my new routers settings back to how they were;
            Screen Shot 2023-02-25 at 20.00.12.png

            My duets IP address is,

            192.168.1.xxx

            Angry ip scanner, if I set the range so my duet will be within 192.168.0.0-192.168.1.255, it doesn't see it?

            undefined 1 Reply Last reply 25 Feb 2023, 20:21 Reply Quote 0
            • undefined
              markz @Dizzwold
              last edited by markz 25 Feb 2023, 20:21

              @Dizzwold Your subnet mask means the router will only use 192.168.0.xxx and you won't see anything at 192.168.1.xxx.

              Here's what I would do.

              Keep the router IP address and subnet mask as is

              Starting IP Adddress -> 192.168.0.50
              Ending IP Address -> 192.168.0.254

              Set the Duet address to 192.168.0.25 (or anything between 2 and 49)

              You may need to restart any other devices on your network to ensure they move to the new router available dynamic address range.

              undefined 2 Replies Last reply 25 Feb 2023, 20:45 Reply Quote 0
              • undefined
                Dizzwold @markz
                last edited by 25 Feb 2023, 20:45

                @markz @Exerqtor

                Okay, I’ll give it a go in the morning.

                Just to say thank you to both for you advice.

                Dizzwold

                1 Reply Last reply Reply Quote 0
                • undefined
                  Dizzwold @markz
                  last edited by 26 Feb 2023, 09:25

                  @markz @Exerqtor

                  I've got issues with setting a new Ip address on the duet.

                  I use it in stand alone mode (no SBC).

                  I've disconnected everything, wired it by usb and ethernet directly to my computer (mac osx)

                  Using serial tools, I get the following;

                  Screen Shot 2023-02-26 at 09.24.22.png

                  The duets in stand alone mode, I don't get it?

                  Dizzwold.

                  undefined undefined 2 Replies Last reply 26 Feb 2023, 10:02 Reply Quote 0
                  • undefined
                    Exerqtor @Dizzwold
                    last edited by 26 Feb 2023, 10:02

                    @Dizzwold

                    Hmm that's weird, what happens if you send M552 S0 followed by M552 S-1 ?

                    undefined 1 Reply Last reply 26 Feb 2023, 10:38 Reply Quote 0
                    • undefined
                      Dizzwold @Exerqtor
                      last edited by 26 Feb 2023, 10:38

                      @Exerqtor

                      I think I tried that and got the same result.

                      I've just checked in terminal + checked the usb in system (on mac osx);
                      Screen Shot 2023-02-26 at 10.30.12.png Screen Shot 2023-02-26 at 10.29.46.png

                      I've just disconnected the ethernet and usb, removed the sd card and put it in my computer to read the config.g;

                      ; Configuration file for Duet 3 MB 6HC (firmware version 3.3)
                      ; executed by the firmware on start-up
                      ;
                      ; generated by RepRapFirmware Configuration Tool v3.3.13 on Mon Sep 19 2022 16:04:20 GMT+0100 (British Summer Time)
                      ; General preferences
                      M575 P1 S1 B57600 ; enable support for PanelDue
                      G90 ; send absolute coordinates...
                      M83 ; ...but relative extruder moves
                      M550 P"Duet 3" ; set printer name
                      M669 K1 ; select CoreXY mode
                      ; Network
                      M552 P192.168.0.xxx S1
                      ; Bed Leadscrew Positions
                      M671 X5:278 Y146:146 P2.0 ; middle left, middle right
                      G4 S1 ;wait for expansion boards to start
                      ; Drives
                      M569 P0.0 S0 ; physical drive 0.0 goes backwards
                      M569 P0.1 S0 ; physical drive 0.1 goes backwards
                      M569 P0.2 S1 ; physical drive 0.2 goes forwards
                      M569 P0.3 S1
                      M569 P121.0 S0 ; physical drive 0.3 goes forwards
                      M584 X0.0 Y0.1 Z0.2:0.3 E121.0 ; set drive mapping
                      M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                      M92 X80.00 Y80.00 Z400.00 E330.12; set steps per mm
                      M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                      M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
                      M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
                      M906 X900 Y900 Z900 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
                      M84 S30 ; Set idle timeout
                      ; Axis Limits
                      M208 X-2 Y-8 Z0 S1 ; set axis minima
                      M208 X330 Y330 Z400 S0 ; set axis maxima
                      ; Endstops
                      M574 X1 S1 P"!121.io1.in" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin !io1.in
                      M574 Y1 S1 P"!io2.in" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin !io2.in
                      ; Z-Probe
                      M574 Z1 Z1 S2 ; set endstops controlled be probe
                      M558 P8 C"^!121.io0.in" H5 F120 T6000 ; set Z probe type to switch and the dive height + speeds
                      G31 P500 X-46 Y-19 Z2.54 ; set Z probe trigger value, offset and trigger height
                      M557 X19:244 Y-2:304 P9 ; define mesh grid
                      ; Heaters
                      M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
                      M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
                      M307 H0 R0.187 K0.192:0.000 D1.89 E1.35 S1.00 B0 ; disable bang-bang mode for the bed heater and set PWM limit
                      M140 H0 ; map heated bed to heater 0
                      M143 H0 S120 ; set temperature limit for heater 0 to 120C
                      M308 S1 P"121.temp0" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
                      M950 H1 C"121.out0" T1 ; create nozzle heater output on out1 and map it to sensor 1
                      M307 H1 R2.498 K0.275:0.349 D6.79 E1.35 S1.00 B0 V24.0 ; disable bang-bang mode for heater and set PWM limit
                      M143 H1 S280 ; set temperature limit for heater 1 to 280C
                      ; Fans
                      M950 F0 C"121.out2" Q500 ; create fan 0 on pin out4 and set its frequency
                      M106 P0 C"Part Cooler" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off
                      M950 F1 C"121.out1" Q500 ; create fan 1 on pin out5 and set its frequency
                      M106 P1 C"Extruder Cooling" S1 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on
                      ; Tools
                      M563 P0 S"Hemera" D0 H1 F0 ; define tool 0
                      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
                      ; Custom settings are not defined
                      ; Emergency Stop
                      M950 J1 C"io4.in"
                      M851 P1 T0 S0 R0
                      ; Miscellaneous
                      M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                      T0
                      M501

                      I'm clueless about this?

                      Dizzwold.

                      undefined undefined 2 Replies Last reply 26 Feb 2023, 11:32 Reply Quote 0
                      • undefined
                        Exerqtor @Dizzwold
                        last edited by Exerqtor 26 Feb 2023, 11:32

                        @Dizzwold

                        I forgot that you werent on a wifi board so M552 S-1 wouldn't do much for you anyways lmao.

                        I suggest you remove everything networking related from your current config.g and add this:

                        ; Network
                        M552 S1 ; Enable network
                        G4 S1 ; Wait a second
                        M586 P0 S1 ; Enable HTTP (for DWC)
                        M586 P1 S1 ; Enable FTP (for remote backups)
                        M586 P2 S0 ; Disable Telnet

                        Then you create runonce.g containing these lines:

                        ; /sys/runonce.g
                        ; called after config.g. When it has been executed, it is automatically deleted!
                        ;
                        M552 S0 ; disable network
                        G4 S1 ; wait a second
                        M552 P192.168.0.14 ; configure IP address
                        G4 S1 ; wait a second
                        M552 S1 ; enable network

                        Put runonce.g in /sys/ on your SD card, insert it in your machine and start it.

                        Then try connecting to 192.168.0.14 after a couple minutes, just to see what happens.

                        Assuming you haven't allready got 192.168.0.14 assigned to some other device ofc!

                        1 Reply Last reply Reply Quote 0
                        • undefined
                          markz @Dizzwold
                          last edited by markz 26 Feb 2023, 12:26

                          @Dizzwold Generally you can't set a computer name with a space character in it. Have you tried using M550 P"Duet3" ?

                          Also I'm confused by that .xxx - are you not showing it? That needs to be number like @Exerqtor shows.

                          undefined 1 Reply Last reply 26 Feb 2023, 12:41 Reply Quote 0
                          • undefined
                            Exerqtor @markz
                            last edited by 26 Feb 2023, 12:41

                            @markz said in Changed ISP:

                            @Dizzwold Generally you can't set a computer name with a space character in it. Have you tried using M550 P"Duet3" ?

                            The space shouldn't be an issue, I've got one in my M550 as well, and it's working flawlessly 😃

                            undefined 1 Reply Last reply 26 Feb 2023, 12:53 Reply Quote 0
                            • undefined
                              markz @Exerqtor
                              last edited by 26 Feb 2023, 12:53

                              @Exerqtor Huh, thanks. I took a look and in their usual clever fashion they display the m550 name but elide the space when setting the hostname.

                              undefined 1 Reply Last reply 26 Feb 2023, 13:30 Reply Quote 0
                              • undefined
                                Dizzwold @markz
                                last edited by Dizzwold 26 Feb 2023, 13:30

                                @markz @Exerqtor

                                The printer name with the space hasn't been an issue before and the last 3, or 4 if you include the dot (.xxx), these are numbers, I'm just not willing to disclose them to the worldwide web.

                                Ive created the runonce.g file in sys on the sd card and removed my network info from the config.g and added the network info above as mentioned.

                                If I open a browser on 192.168.0.14, the page just keeps searching.

                                I now get a link led illuminated on the ethernet connector, where I didn't before (the left green led).

                                This is only the usb cable for power and serial connection and an ethernet cable directly from the Duet to my computer.

                                In serial tools I get the following;
                                Screen Shot 2023-02-26 at 13.25.13.png

                                If I do an Angry IP scan the Duet isn't found, searching from 192.168.0.0 to 192.168.0.255

                                Edit,
                                I've just entered M552 in serial tools and it returns;
                                M552
                                Ethernet is enabled, configured IP address: 192.168.0.14, actual IP address: 192.168.0.14
                                ok

                                But searching in m,y browser for that address, it keeps searching.

                                undefined 1 Reply Last reply 26 Feb 2023, 13:36 Reply Quote 0
                                • undefined
                                  Exerqtor @Dizzwold
                                  last edited by 26 Feb 2023, 13:36

                                  @Dizzwold

                                  Hmm, i'm not sure if powering the board just with an USB connection will be enough (might be wrong on that one though).

                                  undefined 1 Reply Last reply 26 Feb 2023, 13:40 Reply Quote 0
                                  • undefined
                                    Dizzwold @Exerqtor
                                    last edited by 26 Feb 2023, 13:40

                                    @Phaedrux

                                    Can you offer any advice please?

                                    Dizzwold.

                                    undefined undefined 2 Replies Last reply 26 Feb 2023, 16:52 Reply Quote 0
                                    • undefined
                                      Dizzwold @Dizzwold
                                      last edited by Dizzwold 26 Feb 2023, 16:52

                                      @Exerqtor @markz @Phaedrux

                                      Wow, Well I have no explanation for this except I sent Now Broadband an email stating I have a 3d printer, what ip address it had and what new IP address I was now changing it to, ie in the new range of the new router;
                                      Old ISP Talktalk was on 192.168.1.xxx
                                      New ISP Now Broadband is on 192.168.0.xxx

                                      Ten minuets later, all of a sudden the Duet could be found on the new static IP address I'd given it.

                                      No email in reply or any explanation form Now Broadband, just suddenly worked and was found?

                                      If I get an email at any point, I'll let you all know.

                                      Really, really confused.

                                      Dizzwold.

                                      1 Reply Last reply Reply Quote 0
                                      • undefined
                                        markz @Dizzwold
                                        last edited by 26 Feb 2023, 16:52

                                        This post is deleted!
                                        1 Reply Last reply Reply Quote 0
                                        • Phaedruxundefined
                                          Phaedrux Moderator
                                          last edited by 26 Feb 2023, 20:16

                                          Can you send M122 and copy paste here?

                                          Does it still think it's in SBC mode?

                                          Z-Bot CoreXY Build | Thingiverse Profile

                                          undefined 1 Reply Last reply 27 Feb 2023, 10:54 Reply Quote 1
                                          3 out of 25
                                          • First post
                                            3/25
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA