Sorry , i still can not fiqure this out

[Richard F]

@Richard-F

beta server ?

[Exerqtor]

@Richard-F
Why don't you move over to 3.5.1 stable instead of 3.5.0-rc4? It's no bugs in 3.5.0-rc4 that should cause this behaviour that i know of, but running a stable release is usually prefered.

[Richard F]

@Exerqtor ok thanks , ill try that .

[achrn]

The bed settings are in sys/dwc-settings.json What do you have in that file? It's one long line, they should be towards the end so start there and work backwards.

[Richard F]

@Richard-F im now on 3.5.1

i have 2 bed heaters showing but i only have 1 , and both bed and nozzle are reading the same temps .. Cant see what could be causing this in the code

v

[jay_s_uk]

@Richard-F you have 2 M140s. Best post your whole config.g

[Richard F]

This post is deleted!

[Richard F]

; Configuration file for RepRapFirmware on Duet 3 Mini 5+ WiFi
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.5.0-rc.3 on Thu Mar 14 2024 13:43:02 GMT+0000 (Greenwich Mean Time)
 
; General
M550 P"Duet 3"   ; set hostname
;M911 S19.8 R22 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
 
 
 
; Network
M552 S1 
;M587 S"HeX" P"Spyder30"            ; configure WiFi adapter
M586 P0 S1                         ; configure HTTP
 
;-------------------------------
 
; LED Strips
;M950 E0 C"io1.out" T2 ; configure LED strip #0
 
 
;-------------------------------------
 
 
 
; Smart Drivers
M569 P0.0 S0 D3 V3                                                     ; driver 0.0 goes forwards (X axis)
M569 P0.1 S0 D3 V3                                                     ; driver 0.1 goes forwards (Y axis)
M569 P0.2 S0 D3 V3                                                     ; driver 0.2 goes forwards (Z axis)
M569 P20.0 S0 D3 V3                                     
 
 
; Motor Idle Current Reduction
M906 I50                                                               ; set motor current idle factor
M84 S50                                                                ; set motor current idle timeout
 
 
;--------------------------------------
 
; Axes
M584 X0.0 Y0.1 Z0.2                                                    ; set axis mapping
M350 X16 Y16 Z16 I1                                                    ; configure microstepping with interpolation
M906 X800 Y1000 Z700                                                ; set axis driver currents
M92 X80 Y80 Z400                                                       ; configure steps per mm
M208 X0:300 Y0:215 Z-3:160                                             ; set minimum and maximum axis limits
M566 X15 Y15 Z20                                                       ; set maximum instantaneous speed changes (mm/min)
M203 X3000 Y3000 Z500                                                  ; set maximum speeds (mm/min)
M201 X300 Y300 Z30                                                     ; set accelerations (mm/s^2)
 
;-------------------------------
 
 
; Extruders
M584 E20.0                                                             ; set extruder mapping
M350 E16 I1                                                            ; configure microstepping with interpolation
M906 E1000                                                              ; set extruder driver currents
M92 E397                                                               ; configure steps per mm
M566 E800                                                              ; set maximum instantaneous speed changes (mm/min)
M203 E2000                                                            ; set maximum speeds (mm/min)
M201 E400                                                            ; set accelerations (mm/s^2)
 
 
;------------------------------------
; Kinematics
M669 K0                                                              ; configure Cartesian kinematics
 
;----------------------------------------------------------------------------------------------------------
 
; Endstops
M574 X1 P"!io5.in" S1                                                  ; configure X axis endstop
M574 Y1 P"!io6.in" S1                                                  ; configure Y axis endstop
;M574 Z1 P"!io0.in" S1                                                  ; configure Z axis endstop
M574 Z1 S2 ;P"20.io0.in" 
;------------------------
 
 
 
;======================================
;=====================================
 
; Probes
M558 K0 P8 C"20.io0.in" H1.2 F20000 T1000                        ; configure metal proximity sensor via slot #0
G31 P500 X20 Y-20 Z-0     
 
;GRID
M557 X35:290 Y35:210 S80:50     F8000                            ; set Z probe trigger value, offset, and trigger height
 
;======================================
;======================================
 
 
 
 
 
 
 
;-------------------------------------------------
 
; Sensors
;nozzle
M308 S0 P"20.temp0" Y"thermistor" A"Nozzle" T100000 B4388 C7.06e-8   
 
 ;bed
M308 S1 P"temp2" Y"thermistor" A"Bed"  T100000 B4388 C7.06e-8 ;         
 
 
;--------------------------------------------------
 
 
; Nozzle 
M950 H0 C"20.out0" T0
M140 P0 H0                                     ; create heater #0 for the nozzle
M143 H0 P0 T0 C0 S300 A0                          ; configure nozzle heater monitor
 
 
 
;Heaters  BED
M950 H1 C"out0" T1                                 ; create heater #1 for the bed
M140 P1 H1                                          ; assign bed heater to heater 1
M143 H1 P1 T1 C0 S110 A0                            ; configure bed heater monitor
 
 
 
 
;-------------------------------------------
 
; Fans
;M950 F0 C"20.out1"                                  ; create part cooling fan
;M106 P0 S0 L0 X1 B0.1                               ; configure fan 0
 
M950 F1 C"20.out2"                                  ; create hotend cooling fan
M106 P1 S0 L0 X1 B0.1                              ; configure fan 1
 
;--------------
 
 
; Tools
M563 P0 S"Evo" D0  H0 F0                                             
 M568 P0 R0 S0   
 T0         
 
 
 
 
 

[Richard F]

@Richard-F i got rid of 2nd m140 , i have one bed heater.. (fixed)

[Richard F]

; Sensors
;nozzle
M308 S0 P"20.temp0" Y"thermistor" A"Nozzle" T100000 B4388 C7.06e-8   
 
 ;bed
M308 S1 P"temp2" Y"thermistor" A"Bed"  T100000 B4388 C7.06e-8 ;         
 
 
;--------------------------------------------------
 
 
; Nozzle 
M950 H0 C"20.out0" T0
;M140 P0 H1                                     ; create heater #0 for the nozzle
M143 H0 P0 T0 C0 S300 A0                          ; configure nozzle heater monitor
 
 
 
; Heaters  BED
M950 H1 C"out0" T1                                  ; create heater #1 for the bed
M140 P1 H1                                          ; assign bed heater to heater 1
M143 H1 P1 T1 C0 S100 A0                            ; configure bed heater monitor
 
 

[Richard F]

@Richard-F
Ive still no idea why its not letting me set custom bed temps though , everything's just been updated to the latest fw

[Richard F]

You can close thread now if you like

@Richard-F for future problems , i fixed it by turning these off