• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Firmware 2.0RC6 and 1.21.1RC6 released

Scheduled Pinned Locked Moved
Firmware installation
15
49
7.6k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    zerspaner_gerd
    last edited by 29 May 2018, 23:52

    Unfortunately, I still have an unstable DWC connection.

    It will show "pending" for a long time (about 2 seconds), then "failed" and from then on DWC will not be updated anymore.

    0_1527636685678_RC6.JPG

    Can this be due to a bad Wi-Fi connection?
    But at 1.21 I had no such problems.

    Here are the diagnostics:

    === Diagnostics ===
    RepRapFirmware for Duet 2 WiFi/Ethernet version 2.0(RTOS)RC6 running on Duet WiFi 1.02 or later
    Board ID: 08DDM-9FAM2-LW4S4-6J9D2-3S46T-K2T3X
    Used output buffers: 3 of 20 (13 max)
    === RTOS ===
    Static ram: 28380
    Dynamic ram: 96148 of which 0 recycled
    Exception stack ram used: 324
    Never used ram: 6220
    Task NETWORK ready, free stack 404
    Task HEAT blocked, free stack 1200
    Task MAIN running, free stack 3624
    === Platform ===
    Last reset 00:06:32 ago, cause: software
    Last software reset at 2018-05-30 01:12, reason: User, spinning module GCodes, available RAM 6220 bytes (slot 1)
    Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0041f000, BFAR 0xe000ed38, SP 0xffffffff
    Error status: 0
    Free file entries: 10
    SD card 0 detected, interface speed: 20.0MBytes/sec
    SD card longest block write time: 12.7ms
    MCU temperature: min 41.6, current 41.8, max 43.4
    Supply voltage: min 24.5, current 24.6, max 24.8, under voltage events: 0, over voltage events: 0
    Driver 0: standstill, SG min/max not available
    Driver 1: standstill, SG min/max not available
    Driver 2: standstill, SG min/max not available
    Driver 3: standstill, SG min/max not available
    Driver 4: standstill, SG min/max not available
    Date/time: 2018-05-30 01:19:24
    Slowest loop: 15.74ms; fastest: 0.07ms
    === Move ===
    Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
    Scheduled moves: 0, completed moves: 0
    Bed compensation in use: none
    Bed probe heights: 0.000 0.000 0.000 0.000 0.000
    === Heat ===
    Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
    === GCodes ===
    Segments left: 0
    Stack records: 2 allocated, 0 in use
    Movement lock held by null
    http is idle in state(s) 0
    telnet is idle in state(s) 0
    file is idle in state(s) 0
    serial is idle in state(s) 0
    aux is idle in state(s) 0
    daemon is idle in state(s) 0
    queue is idle in state(s) 0
    autopause is idle in state(s) 0
    Code queue is empty.
    === Network ===
    Slowest loop: 30.41ms; fastest: 0.01ms
    Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
    HTTP sessions: 1 of 8
    - WiFi -
    Network state is running
    WiFi module is connected to access point
    Failed messages: pending 0, notready 0, noresp 0
    WiFi firmware version 1.21
    WiFi MAC address 60:01:94:73:5e:04
    WiFi Vcc 3.38, reset reason Turned on by main processor
    WiFi flash size 4194304, free heap 15688
    WiFi IP address 192.168.188.40
    WiFi signal strength -63dBm, reconnections 0, sleep mode modem
    Socket states: 0 0 0 0 0 0 0 0
    === Expansion ===

    Maybe this helps.
    What else can I do to debug the error?

    Board: Duet WiFi 1.03 | Firmware Version: 3.1.1 | WiFi Server Version: 1.23 | Web Interface Version: 3.1.1

    undefined 1 Reply Last reply 30 May 2018, 06:59 Reply Quote 0
    • undefined
      Donpi
      last edited by 30 May 2018, 05:06

      Hi,
      I think I found a little bug.
      (However I'm not sure it'is caused by the new release.)

      It start the load filament macro on Tool 0, and when i see that this was not the correct macro, I shuted down the Duet.
      When powered up again. I can no more right click on Tool 0 to use the filament macro.

      Tool 1 keep working right.

      Bye.

      undefined 1 Reply Last reply 30 May 2018, 08:00 Reply Quote 0
      • undefined
        SM3D
        last edited by 30 May 2018, 06:40

        @dc42 - As I mentioned yesterday, I could not find my old files in DWC but all the files are present when I access the card via panel due. I am at work so I will clear the cache and reinstall the duet web control when I get back home today.

        I think somebody mentioned in other thread about fan sliders. I also have the same problem - I am able to slide the fan control by holding the left mouse button but when I leave the button the slider bounces back to previous value. If I start clicking step by step in small increments 5% each time, it works.

        Cheers,
        Vasan

        Good judgement comes from experience but experience comes from bad judgements

        1 Reply Last reply Reply Quote 0
        • undefined
          dc42 administrators @zerspaner_gerd
          last edited by 30 May 2018, 06:59

          @zerspaner_gerd said in Firmware 2.0RC6 and 1.21.1RC6 released:

          Unfortunately, I still have an unstable DWC connection.

          It will show "pending" for a long time (about 2 seconds), then "failed" and from then on DWC will not be updated anymore.

          The WiFi code hasn't changed between 1.21 and 2.0. As your WiFi signal strength is quite low, I suspect there may have been a change in your WiFi environment - in which case, reverting to firmware 1.21 will show the same problem (if the change in the environment is still present).

          Are you able to reconnect DWC after the error? Have you increased the AJAX retry count in DWC from the default of 1?

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • undefined
            boldnuts
            last edited by 30 May 2018, 07:35

            Just ran a 10 hour print with 2.0RC6 with no issue's to report on my Duet Ethernet P3 Steel.

            1 Reply Last reply Reply Quote 0
            • undefined
              dc42 administrators @SM3D
              last edited by 30 May 2018, 07:56

              @sm3d said in Firmware 2.0RC6 and 1.21.1RC6 released:

              @dc42 I updated my firmware just now to 2.0RC6 and it wiped many of my .gcode files. Moreover, I could upload .gcode files without any error but I could not find them in the interface. I also cannot create a folder. Any suggestions?

              Cheers,
              Vasan

              The number of GCode files in a single folder that can be displayed by DWC is lower than before. This was required to fix other issues. So I suspect that the files are all there, just not being displayed. Likewise the new folder you created. The workaround is to move some files into subfolders. If you can't see any subfolders in DWC, you may have to move the SD card to a PC to do this. Alternatively, use the backup facility in DWC to backup the files that you can see, then delete them; then you should be able to see the other files.

              I'll add this to the upgrade notes.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              undefined 1 Reply Last reply 30 May 2018, 08:16 Reply Quote 0
              • undefined
                dc42 administrators @Donpi
                last edited by 30 May 2018, 08:00

                @donpi said in Firmware 2.0RC6 and 1.21.1RC6 released:

                Hi,
                I think I found a little bug.
                (However I'm not sure it'is caused by the new release.)

                It start the load filament macro on Tool 0, and when i see that this was not the correct macro, I shuted down the Duet.
                When powered up again. I can no more right click on Tool 0 to use the filament macro.

                Tool 1 keep working right.

                Bye.

                Does reloading DWC fix this?

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                undefined 1 Reply Last reply 30 May 2018, 08:04 Reply Quote 0
                • undefined
                  Donpi @dc42
                  last edited by 30 May 2018, 08:04

                  @dc42

                  Sorry but what is DWC ?

                  1 Reply Last reply Reply Quote 0
                  • undefined
                    dc42 administrators
                    last edited by 30 May 2018, 08:09

                    Duet Web Control.

                    Duet WiFi hardware designer and firmware engineer
                    Please do not ask me for Duet support via PM or email, use the forum
                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                    undefined 1 Reply Last reply 30 May 2018, 08:36 Reply Quote 0
                    • undefined
                      resam @dc42
                      last edited by 30 May 2018, 08:16

                      @dc42 regarding the number of gcode files per folder and moving them into subfolders:

                      I think there is no g-code to move or rename a file on the SD card.
                      M30 deletes a file - but thats about it...

                      DWC has rr_move and rr_mkdir and rr_delete.
                      Would be nice to add this to the Firmware wishlist.

                      Looking through https://reprap.org/wiki/G-code, it seems no other firmware supports this either...
                      All the "good" numbers around M20-M30 that do things with the SD card are already taken.

                      1 Reply Last reply Reply Quote 1
                      • undefined
                        Donpi @dc42
                        last edited by 30 May 2018, 08:36

                        @dc42 Haha ok

                        Totaly powering of the Duet does nothing.
                        But maybe i have a cache problem.
                        I'll try tonight.

                        1 Reply Last reply Reply Quote 0
                        • undefined
                          wilriker
                          last edited by 30 May 2018, 12:00

                          Just finished a 3:45h print successfully with no issues apart from warping - but that is clearly not a problem of the Duet. 😉 👍

                          Manuel
                          Duet 3 6HC (v0.6) with RPi 4B on a custom Cartesian
                          with probably always latest firmware/DWC (incl. betas or self-compiled)
                          My Tool Collection

                          1 Reply Last reply Reply Quote 0
                          • undefined
                            zerspaner_gerd
                            last edited by 30 May 2018, 22:24

                            @dc42 said in Firmware 2.0RC6 and 1.21.1RC6 released:

                            @zerspaner_gerd said in Firmware 2.0RC6 and 1.21.1RC6 released:

                            Unfortunately, I still have an unstable DWC connection.

                            It will show "pending" for a long time (about 2 seconds), then "failed" and from then on DWC will not be updated anymore.

                            Are you able to reconnect DWC after the error?

                            Yes, I can immediately press on Disconnect Connect.

                            Have you increased the AJAX retry count in DWC from the default of 1?

                            I have played with this attitude something (up to 2) without change.

                            I suspect there may have been a change in your WiFi environment - in which case, reverting to firmware 1.21 will show the same problem (if the change in the environment is still present).

                            It's enough if I downgrade to DWC 1.21

                            Current combination:

                            Firmware Version: 2.0 (RTOS) RC6 (2018-05-29b4)
                            WiFi server version: 1.21
                            Web Interface Version: 1.21

                            No noticeable delays. (over an hour) With 1.21.1 it was between 10 seconds and a maximum of 5 minutes.

                            The debug mode shows the same error, only the difference is, it just continues after the error.

                            0_1527717963254_DWC 1.21 Debug.png

                            So it seems to me that the cause of DWC is not RFF, right?

                            @donpi said in Firmware 2.0RC6 and 1.21.1RC6 released:

                            I can no more right click on Tool 0 to use the filament macro.

                            I can confirm that, that's exactly the case with me. I already wrote it at RC5.
                            https://forum.duet3d.com/topic/5394/new-firmware-2-0rc5-available/74

                            Board: Duet WiFi 1.03 | Firmware Version: 3.1.1 | WiFi Server Version: 1.23 | Web Interface Version: 3.1.1

                            1 Reply Last reply Reply Quote 0
                            • undefined
                              3dmntbighker
                              last edited by 30 May 2018, 23:08

                              Installed rc6 in my coreXY and so far so good. I don't have many extra goodies yet to trip it up of course.

                              Scratch built CoreXY with Maestro
                              Heavily modified Ender 3 with Maestro
                              MPCNC work in progress with Duet WiFi

                              1 Reply Last reply Reply Quote 0
                              • undefined
                                Danal
                                last edited by 31 May 2018, 04:07

                                Installed on BFD (Big Fast Delta).

                                Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
                                Firmware Electronics: Duet WiFi 1.02 or later
                                Firmware Version: 2.0(RTOS)RC6 (2018-05-29b4)
                                WiFi Server Version: 1.21
                                Web Interface Version: 1.21.1
                                Collected Data
                                Warm-Up Time Current Layer Time Last Layer Time Print Duration
                                01m 36s 09s 58s 8h 44m 53s
                                Estimations
                                Based on Filament Usage File Progress Layer Time
                                Time Left 16h 37m 49s 22h 27m 39s 24h 54m 39s

                                No issues.

                                Delta / Kossel printer fanatic

                                1 Reply Last reply Reply Quote 0
                                • undefined
                                  SM3D
                                  last edited by 31 May 2018, 05:42

                                  @dc42 you are right. I took the SD card and made subfolders to make sure there are less than 25 files in each folder. Now I see all the files in DWC.

                                  I did a small 1 hour print and no issues so far.

                                  Cheers,
                                  Vasan

                                  Good judgement comes from experience but experience comes from bad judgements

                                  1 Reply Last reply Reply Quote 0
                                  • undefined
                                    timcurtis67
                                    last edited by 31 May 2018, 10:53

                                    Just ran a 8 hr print with no issues. Running IDEX ditto printing with both heads at the same time.

                                    Works great so far.

                                    1 Reply Last reply Reply Quote 0
                                    • undefined
                                      SM3D
                                      last edited by 1 Jun 2018, 04:30

                                      @dc42 I noticed one more issue. It happened twice after 2.0RC6 upgrade (past 2 days) - whenever I update the config.g file, DWC says it cannot be updated and loses connection. It shows under system editor only config.g.bak but no config.g files.

                                      When I shut down the printer and restart again, it cannot connect or show my tools because config.g is not present. I have to take the SD card out and rename config.g.bak to config.g to make things work again. This never happened to me in previous upgrades.

                                      Cheers,
                                      Vasan

                                      Good judgement comes from experience but experience comes from bad judgements

                                      undefined 1 Reply Last reply 2 Jun 2018, 14:50 Reply Quote 0
                                      • undefined
                                        Donpi
                                        last edited by Donpi 6 Jan 2018, 21:19 1 Jun 2018, 17:18

                                        Today I tried to print with two extruder and get a strange behaviour.

                                        I'm printing the Kisslicer Wizzard box with extruder 1 to the raft and extruder 0 to the main object.

                                        And when the printer change from tools 1 to tool 0, the Duet switches to full steps. The print becom impossible as everthing goes 256 x faster and is 256 x bigger.

                                        That worked at lest once with firmware 1.21.

                                        May that help

                                        PS : I checked the gcode after M92, M350 and M569 but fond none of them.

                                        1 Reply Last reply Reply Quote 0
                                        • undefined
                                          resam @SM3D
                                          last edited by 2 Jun 2018, 14:50

                                          @sm3d said in Firmware 2.0RC6 and 1.21.1RC6 released:

                                          It shows under system editor only config.g.bak but no config.g files.
                                          When I shut down the printer and restart again, it cannot connect or show my tools because config.g is not present. I have to take the SD card out and rename config.g.bak to config.g to make things work again. This never happened to me in previous upgrades.

                                          I had the same thing happen to my printer once, maybe 2-3 months ago. Don't remember which FW I had back then, maybe 1.20?
                                          So, I don't think this is a new thing.

                                          1 Reply Last reply Reply Quote 0
                                          22 out of 49
                                          • First post
                                            22/49
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA