Dave's so proud

sjason1377

RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet Ethernet 1.02 or later
Firmware Version: 2.01(RTOS) (2018-07-26b2)
Web Interface Version: 1.21.2-dc42

ok guess what probe doesn't work still

sjason1377

; Endstops
M574 X1 Y1 S1 ; Set active low endstops
M574 Z0
M558 P9 X0 Y0 Z1 H5 F100 T2000 ; Set Z probe type to switch, the axes for which it is used and the dive height + speeds
G31 P600 X0 Y12 Z.96; Set Z probe trigger value, offset and trigger height
M557 X52:300 Y60:335 S40 ; Define mesh grid

deckingman

This post is deleted!

Danal

This post is deleted!

sjason1377

RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet Ethernet 1.02 or later
Firmware Version: 2.01(RTOS) (2018-07-26b2)
Web Interface Version: 1.21.2-dc42

sjason1377

; Endstops
M574 X1 Y1 S1 ; Set active low endstops
M574 Z0
M558 P9 X0 Y0 Z1 H5 F100 T2000 ; Set Z probe type to switch, the axes for which it is used and the dive height + speeds
G31 P600 X0 Y12 Z.96; Set Z probe trigger value, offset and trigger height
M557 X52:300 Y60:335 S40 ; Define mesh grid

correct version and correct wording in config.g probe is unresponsive. a year of flawless performance under build 1.19.1 and now nothing.

Danal

This post is deleted!

fcwilt

@sjason1377 said in Dave's so proud:

; Endstops
M574 X1 Y1 S1 ; Set active low endstops
M574 Z0
M558 P9 X0 Y0 Z1 H5 F100 T2000 ; Set Z probe type to switch, the axes for which it is used and the dive height + speeds
G31 P600 X0 Y12 Z.96; Set Z probe trigger value, offset and trigger height
M557 X52:300 Y60:335 S40 ; Define mesh grid

correct version and correct wording in config.g probe is unresponsive. a year of flawless performance under build 1.19.1 and now nothing.

The current docs for M558 report that the X, Y and Z parameters are obsolete.

Perhaps that is causing some sort of problem?

Frederick

sjason1377

I would never had upgraded except for those false heater faults he said was a bug from the old version. Now he's got no support for this problem because he won't admit there is one. That my issue. It take many failures from many user before he responds. History proves I was not at fault before. I'm not now either.

sjason1377

I'm not proud I'm not saying I have any answers. I know my spelling sucks. But I'm no liar. We depend on him to help with these issue. But where does that leave us when he won't help.

bot

Do you expect David to drop everything in his real life to help one of the rudest users ever to come on these boards?

You need to learn to be patient, and/or how to resolve issues yourself.

Danal

Ooops... just read the whole thread from the top.

BYE.

You want support from the community, you need a whole different attitude.

fcwilt

@sjason1377 said in Dave's so proud:

; Endstops
M574 X1 Y1 S1 ; Set active low endstops
M574 Z0
M558 P9 X0 Y0 Z1 H5 F100 T2000 ; Set Z probe type to switch, the axes for which it is used and the dive height + speeds
G31 P600 X0 Y12 Z.96; Set Z probe trigger value, offset and trigger height
M557 X52:300 Y60:335 S40 ; Define mesh grid

correct version and correct wording in config.g probe is unresponsive. a year of flawless performance under build 1.19.1 and now nothing.

Do you have a Z endstop in addition to the Z probe?

In the M574 Z0 there is no S parameter - which indicates an active high endstop - is that correct?

Frederick

sjason1377

yes that's correct. I went back to p7 and it works now

sjason1377

@deckingman eat my load!

fcwilt

@sjason1377 said in Dave's so proud:

yes that's correct. I went back to p7 and it works now

Did you try the latest version after removing the obsolete parameters from M558?

And you do have a Z endstop in addtion to the Z probe?

Frederick

deckingman

@sjason1377 Thanks for this chat message

"hey decking eat my nut load bitch"

Like I said, I'd like to help you but only a qualified psychiatrist could do that.

T3P3Tony

Following an email where I asked sjason1377 to stop abusing/attacking people on the forum he continued with this behaviour so I have banned him.

dc42

@sjason1377 said in Dave's so proud:

yes that's correct. I went back to p7 and it works now

From https://duet3d.dozuki.com/Wiki/Gcode:

P5 (from RepRapFirmware 1.14) selects a switch by default (normally closed) for bed probing between the In and Gnd pins of the Z-probe connector (Duet 0.8.5 and Duet WiFi).
...
P7 (from RepRapFirmware 1.20) selects a switch (by default normally closed) connected to the Z endstop input.
...
P9 (from RepRapFirmware 1.21RC2) is as P5 but for a BLTouch probe that needs to be retracted and redeployed between probe points.

So if P7 worked, he must have his BLTouch connected to the Z endstop input; whereas P9 requires it to be connected to the Z probe input.

fcwilt

@dc42 said in [Dave's so proud]

So if P7 worked, he must have his BLTouch connected to the Z endstop input; whereas P9 requires it to be connected to the Z probe input.

One thing I have noticed is that folks who are not good at attention to details often struggle with configuring 3D printers (and other things as well).

Aside from the occasional mistake they we all make from time to time it is clear you very much know what you are doing.

Thank you for your hard work, the Duet family of products has made building my printers so much easier and enjoyable.

Frederick