Newbie: New Install on Ender 5 Plus---Willing to PAY$$$
-
@shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
M558 P9 C"^!zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
zprobe in does not normally need to be inverted for the bltouch.
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
the offset x and y is missing
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0tempThen Beta value is incorrect, try the beta value from the guide, as creality tends to use the same thermistors
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H1 T45 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned onyou configured both fans to be Thermostatic controled. this way you have no part cooling fan that can be controlled.
also add a T0 to the end of your config.
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
do you have the motor specs for the ender 5 plus?
but you could test these values and check the motor temperature by hand during printing.
you might want to increase E800 to E900 as in the guideM92 X80.00 Y80.00 Z400.00 E130.00 ; set steps per mm
checking the marlin example config for the ender 5 plus
https://github.com/MarlinFirmware/Configurations/blob/import-2.0.x/config/examples/Creality/Ender-5 Plus/Configuration.h
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 800, 93.02 }
it seems you need Z800 -
Have you ever powered on the board with USB or anything yet?
Part 3 of the guide veti linked above goes over initial commissioning. Moving motors safely to test, that sort of thing. Try taking a look at that.
https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+3:+Commissioning/39
The duet is pretty hard to kill, but there are a few wiring things you should absolutely double check.
First is your motor phase pairings. Failure to get the pairs right would probably just lead to an error message and the motors not working, but it could also damage the drivers, so best to get it sorted first. Here's how.
Second is the fan polarity. Positive and negative must be the right way round or you're likely to damage the fan or the fan mosfet on the board or both, so make sure you've got that sorted out before testing the fans.
-
@Phaedrux said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
Have you ever powered on the board with USB or anything yet?
Yes -
@Veti
https://www.amazon.com/Aibecy-Creality-Stepping-Accessory-Replacement/dp/B07MVTFL3R/ref=sr_1_1_sspa?dchild=1&keywords=creality+stepper+motor&qid=1605337045&sr=8-1-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzUjk2ME9MS0RHTTZJJmVuY3J5cHRlZElkPUEwMTk3MDI4MlRHWlVWQks3QU9ESyZlbmNyeXB0ZWRBZElkPUEwNjcyNDU0WjhHMEo4NEtaM1JVJndpZGdldE5hbWU9c3BfYXRmJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ== -
@Veti said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
@shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
M558 P9 C"^!zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
zprobe in does not normally need to be inverted for the bltouch.
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
the offset x and y is missing
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0tempThen Beta value is incorrect, try the beta value from the guide, as creality tends to use the same thermistors
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H1 T45 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned onyou configured both fans to be Thermostatic controled. this way you have no part cooling fan that can be controlled.
also add a T0 to the end of your config.
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
do you have the motor specs for the ender 5 plus?
but you could test these values and check the motor temperature by hand during printing.
you might want to increase E800 to E900 as in the guideM92 X80.00 Y80.00 Z400.00 E130.00 ; set steps per mm
checking the marlin example config for the ender 5 plus
https://github.com/MarlinFirmware/Configurations/blob/import-2.0.x/config/examples/Creality/Ender-5 Plus/Configuration.h
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 800, 93.02 }
it seems you need Z800I will go back in the configurator and post my fixes. Thanks! Most of what u said is chinese to me but I will do some googling and try
-
None of these values will autopopulate after I turn it on and auto homes itself and tests itself out?
-
which part did you not understand? please be specific, then we can further elaborate.
None of these values will autopopulate after I turn it on and auto homes itself and tests itself out?
no.
-
Did you ever learn how to ride a bicycle?
If so do you remember the leap of faith you had to make without the safety net of training wheels?
Follow the steps to get the printer running, check your wiring multiple times, and trust yourself and take the leap, and flip the switch.
-
@CaLviNx said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
Did you ever learn how to ride a bicycle?
If so do you remember the leap of faith you had to make without the safety net of training wheels?
Follow the steps to get the printer running, check your wiring multiple times, and trust yourself and take the leap, and flip the switch.
LOL. I didnt think it would be this complicated before I installed it. I thought it would be a quick swap. Anyways theres no turning back now.
-
@Veti Hows this?
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Nov 15 2020 03:22:47 GMT-0500 (Eastern Standard Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"E5Plus" ; set printer name; Network
M551 P"xxxxx" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E412.60 ; set steps per mm
M566 X1200.00 Y1200.00 Z60.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z1200.00 E6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z1400 E1000 I50 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X350 Y350 Z400 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F600 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X16.3 Y14 Z1.7 ; set Z probe trigger value, offset and trigger height
M557 X15:190 Y15:190 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 C4700 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
M308 S1 P"e0temp" Y"thermistor" T100000 B4092 C4700 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDueI dont see where the Heater for the hot end should max at 280. Also there are 2 fans on the hot end. Shouldnt the values be identical? I got a lot of the fixes from someones 5 Pro config
-
@shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
I dont see where the Heater for the hot end should max at 280.
Add
M143 H1 S280at the end of the heater block under the M307.Otherwise I don't see any obvious issues.
You can send M98 P"config.g" in the console to see if there are any syntax errors.
Otherwise it's time to do some testing.
-
@shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
M92 X80.00 Y80.00 Z400.00 E412.60 ; set steps per mm
as i posted earlier the Z steps according to marlin are Z800
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 C4700 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
M308 S1 P"e0temp" Y"thermistor" T100000 B4092 C4700 ; configure sensor 1 as thermistor on pin e0tempdelete the C4700 thats not the resistance. you can leave R empty and the correct default is choosen.
-
@Phaedrux said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
M143 H1 S280
OK so I edited and turned on.
Seems ok. Temps are hovering at 22 deg C with heaters off.
Motors are F'ed up. Z looks good. Its the X and Y. I got some error codes.11/16/2020, 1:18:45 AM M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N8PS0-6J1DJ-3SD6K-KSSHN
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93672 of which 44 recycled
Exception stack ram used: 264
Never used ram: 9112
Tasks: NETWORK(ready,384) HEAT(blocked,1224) MAIN(running,1880) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:04:52 ago, cause: software
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 8240 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 24.7, current 25.6, max 26.1
Supply voltage: min 24.1, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-11-16 01:18:41
Cache data hit count 507426640
Slowest loop: 6.91ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.8ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.88ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address f4:cf:a2:66:99:4f
WiFi Vcc 3.38, reset reason Unknown
WiFi flash size 4194304, free heap 23640
WiFi IP address 192.168.2.8
WiFi signal strength -43dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
11/16/2020, 1:17:30 AM M120 G91 G1 X-1 F6000 G90 M121
Error: G0/G1: insufficient axes homed
11/16/2020, 1:14:17 AM Connection established
11/16/2020, 1:13:42 AM Connection interrupted, attempting to reconnect...
11/16/2020, 1:13:32 AM Emergency Stop! Reset the controller to continue.
11/16/2020, 1:13:32 AM Emergency stop, attemping to reconnect...
11/16/2020, 1:13:31 AM Warning: motor phase B may be disconnected reported by driver(s) 2
11/16/2020, 1:13:26 AM Warning: motor phase B may be disconnected reported by driver(s) 2
11/16/2020, 1:13:22 AM Warning: motor phase B may be disconnected reported by driver(s) 2
11/16/2020, 1:13:17 AM Warning: motor phase B may be disconnected reported by driver(s) 0 1 2
11/16/2020, 1:13:16 AM Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
11/16/2020, 1:13:07 AM Connection established
11/16/2020, 1:12:52 AM Connection interrupted, attempting to reconnect...
HTTP request timed out
11/16/2020, 1:12:40 AM Upload of config.g successful after 0s
11/16/2020, 1:07:50 AM Connected to 192.168.2.8
- WiFi -
-
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Nov 15 2020 03:22:47 GMT-0500 (Eastern Standard Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"E5Plus" ; set printer name; Network
M551 P"xxxxx" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E412.60 ; set steps per mm
M566 X1200.00 Y1200.00 Z60.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z1200.00 E6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z1400 E1000 I50 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X350 Y350 Z400 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F600 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X16.3 Y14 Z1.7 ; set Z probe trigger value, offset and trigger height
M557 X15:190 Y15:190 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; 280 deg max on hot end; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue -
@Phaedrux said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
M98 P"config.g"
11/16/2020, 1:23:54 AM M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365CI have that little daughter board connected for the bed heat. Looks like a relay board. Bed heat output on D3D connects to smaller board. Looks like the bed heat output triggers that smaller board. But if you think I should connect the bed straight to bed out on D3D I will
-
@shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
11/16/2020, 1:13:31 AM Warning: motor phase B may be disconnected reported by driver(s) 2
11/16/2020, 1:13:26 AM Warning: motor phase B may be disconnected reported by driver(s) 2
11/16/2020, 1:13:22 AM Warning: motor phase B may be disconnected reported by driver(s) 2
11/16/2020, 1:13:17 AM Warning: motor phase B may be disconnected reported by driver(s) 0 1 2this indicates that your wiring of the phases are incorrect.
-
@Veti said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
@shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
11/16/2020, 1:13:31 AM Warning: motor phase B may be disconnected reported by driver(s) 2
11/16/2020, 1:13:26 AM Warning: motor phase B may be disconnected reported by driver(s) 2
11/16/2020, 1:13:22 AM Warning: motor phase B may be disconnected reported by driver(s) 2
11/16/2020, 1:13:17 AM Warning: motor phase B may be disconnected reported by driver(s) 0 1 2this indicates that your wiring of the phases are incorrect.
I triple checked them. I compared from the stock board to the D3D. I will check again
-
@Veti
so just Extruder,x and y? And just the B phase? -
As it's only one phase of each driver that's reported as disconnected, a likely cause is a bad crimp connection.
-
M584 X0 Y1 Z2
x y z, presumably you have not moved the extruder.
the stock board config does not matter, as each board has different layouts.
did you follow the guide to find the phases of the motors?
