Artillery Genius Duet 2 Wifi Configuration
-
@d0minik96 said in Artillery Genius Duet 2 Wifi Configuration:
Also Extruder temp is shown as 200 °C
are you sure the thermistor setting is correct?
why do you have this commented out?
M308 S1 P"spi.cs1" Y"rtd-max31865" -
@Veti i set it upo wrong with the configurator. it should be thermistor 1 in merlin like the heatbed. heatbed sensor shows 20°C so it works. Not sure what i did wrong with the extruder thermistor
-
is it 200 or 2000 ?
-
@Veti 2000
-
So i just did some try and error. I have 2 Z motors. They worked against each other. Now it they work right.
y axis works fine. When i move X-axis z Axis moves aswell. I move the motors without homing atm.
I plugged all motors off and tried each motor alone with the y axis. they worked all great. not sure why they move together when i move z or y axis alone in the dashboard. U have any suggestions what i can check ? -
2000 means open circuit.
so check the wiring.
measure the resistance with a multimeter
-
@Veti ok!
-
@Veti Both Thermistors work now! Thank you very much
U have any idea why both x and z axis move when i try to move one of them ?
-
i could be because of mesh compensation
how are you moving the axis?
-
@Veti I just do the M564 S0 H0 Command so i can move axis without homing
and than i just go to dashboard and click on the bottons to move the axis manual. I did not active do a mesh bed compensation, is there a way to check in config if there is any setting done ? -
in what way is the z axis moving when you move the x
-
post your current config.g m122 and a picture of your wiring
-
@Veti The movement of second axis is not random, if i move pos the second axis does as well. when i move neg. it moves neg. aswell.
M112:
m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6M2-NW4SN-6J9D2-3SD6S-9VT7M
Used output buffers: 3 of 24 (18 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73284 of which 24 recycled
Never used RAM 15312, free system stack 189 words
Tasks: NETWORK(ready,160) HEAT(blocked,309) MAIN(running,450) IDLE(ready,19)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:06:15 ago, cause: power up
Last software reset at 2021-01-29 19:39, reason: User, GCodes spinning, available RAM 15276, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 21.1, current 28.5, max 29.1
Supply voltage: min 24.1, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-01-29 20:09:26
Cache data hit count 464421949
Slowest loop: 6.16ms; fastest: 0.20ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 2.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.17ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21RC2
WiFi MAC address 40:f5:20:1d:c0:8e
WiFi Vcc 3.45, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 16912
WiFi IP address 192.168.178.160
WiFi signal strength -51dBm, mode none, reconnections 0, sleep mode modem
Clock register ffffffff
Socket states: 0 0 0 0 0 0 0 0
- WiFi -
-
did you plug in x motor into the second z header by accident?
WiFi firmware version 1.21RC2
you did not update your wifi firmware
-
Could this be the problem ? When i click on Compensation and Callibration it says: Compensation in use: none.
Im 100% Sure i use the right motor in the right plugs. Tested the connection like an hour ago and tested every motor while i plugged off all others
-
Upload this zip file to the system tab in DWC.
https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/Duet2and3Firmware-3.2.zip
-
@Phaedrux I will test it after installation!
-
post your current config
-
@Phaedrux Reply how long does the installation normally take ? Now i cant connect. Does it save my Networksettings normally ?
-
@Veti The current config is the one i posted a bit upper in this thread. did not change anything since than and i cant connect to my board due to the update right now