G32 ERROR
-
M98 P"config.g" and post the results?
And just to confirm, you have all Z motors and endstops connected to the Duex?
And your duex is wired up for power/ground as shown here?
https://duet3d.dozuki.com/Wiki/Duex2_and_Duex5_Features#Section_Wiring
-
1/31/2021, 11:51:56 PM: M98 P"config.g": HTTP is enabled on port 80 FTP is disabled TELNET is disabled Error: bad grid definition: Too many grid points; suggest increase spacing to 21.0mm Warning: Macro file config-override.g not found sorry I thought I did post my M98. but everything works correctly on my duex5 except my end stops. If I run M564 S0 H0 all Zmotors work correctly. the duex5 is wired correctly as and all endstops wired correctly as well
-
@moe-adams9093 said in G32 ERROR:
M569 P8 S0 ; physical drive 7 goes Backwards
The comment says 7 the command specifies 8.
Have you manually activated each Z end stop sensor, one at a time, and run M119 to verify the reported end stop state?
Frederick
-
Yes I did and they all trigger as Z max endstop on m119
-
M569 P5 S1
M569 P6 S1
M569 P8 S0
M569 P9 S0
Yes this is the correct format for all of my z axis motors 2 motors are mirror to the other 2 thats why I have p8 s0 and p9 s0 -
@moe-adams9093 said in G32 ERROR:
Yes I did and they all trigger as Z max endstop on m119
Great.
Can you easily remove the bed assembly so we can test each Z stepper one at a time?
Frederick
-
I already did to avoid crashes
-
As I explained driver number 6 on the duex5 works the way it supposed to but when add another endstop to my config.g it won't work like for example and click home Z it won't work only driver 6 even when I added them all
-
@moe-adams9093 said in G32 ERROR:
I already did to avoid crashes
Great.
Then I would try this.
In you config.g file make duplicate entries for the M584 M350 M92 M566 M203 M201 M906 commands.
Comment out the first set of commands so you can easily return to using them.
In the second set of commands
- Change M584 X10 Y11 Z5:6:8:9 E3:4 to M584 X10 Y11 Z5 A6 B8 C9 E3:4
- Change the other commands as needed to include the new axes A B and C
This will allow you to access each Z stepper individually (as Z A B or C) using the job buttons in the DWC.
Frederick
-
This post is deleted! -
@fcwilt Ok what about when I use my Z-Probe and to run G32 how that going work
-
@moe-adams9093 said in G32 ERROR:
@fcwilt Ok what about when I use my Z-Probe and to run G32 how that going work
The changes I suggested were only for TESTING to verify that each Z stepper on it's own was working as expected with no possible interactions with the other Z steppers.
Once you were sure that they were working then you would restore the original stepper configuration commands.
Frederick
-
Ok make sense thank you
-
M574 Z2 S1 P"!exp.e2stop+!exp.e3stop+!exp.e5stop+!exp.e6stop"
Instead of using exp.e#stop let's try using the pin names for the actual deux pins.
duex.e2stop
duex.e3stop
duex.e4stop
duex.e5stop
duex.e6stopWhen using these names I think you can remove the !, but please test carefully.
-
@Phaedrux so I did move the ! And did exactly as
M574 Z2 S1 P" duex.e2stop+ duex.e3stop+duex.e5stop+ duex.e6stop"; when I click home Z axis are not moving they do get power but no signal -
And if you check M119 what does the endstop status say?
If it says the z endstop is triggered but the switch isn't pressed, then you would need to add the ! again to invert the signal. -
@Phaedrux yes thats what I got
2/1/2021, 1:30:18 PM: M119: Endstops - X: not stopped, Y: not stopped, Z: at max stop, Z probe: not stopped -
I'm going to put ! back and see what's going on
-
The only one is communicating probably is e6stop
-
Its not working. when I added this code
M574 Z2 S1 p"!duex.e6stop+!duex.e5stop+!duex.e3stop+!duex.e4stop";
and run M119M119 Endstops - X: at min stop, Y: at min stop, Z: no endstop, Z probe: not stopped but If I remove any one of any of the above endstops
example:
M574 Z2 S1 p"!duex.e6stop+!duex.e5stop+!duex.e3stop";my M119 will show Z end stop is available I don't know what's causing this issue to not take all 4endstops. also when I press any of the endstops they all stop automatically not individually. I don't know whats happening maybe my duex 5 is bad or if you guys know any solution around please let me know. thank you