Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    help with config.g

    Scheduled Pinned Locked Moved
    General Discussion
    5
    29
    1.6k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • fcwiltundefined
      fcwilt
      last edited by

      Hi,

      Please do the following from the DWC console:

      Execute M122 and post the results

      Execute M98 P"config.g" and post the results

      Thanks.

      Frederick

      Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

      patterson6undefined 1 Reply Last reply Reply Quote 0
      • jay_s_ukundefined
        jay_s_uk @patterson6
        last edited by jay_s_uk

        @patterson6
        have you included power to the out 0 power in? out0 won't work without that.

        These are the correct settings for a daughter board with PT100 assuming you are using input number 1

        M308 S1 P"spi.cs1" Y"rtd-max31865"								; PT100 Temperature Sensor

        you can interpolate the motors at any steps on the duet 3 but going higher than x16 probably won't make much difference.

        Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

        patterson6undefined 1 Reply Last reply Reply Quote 0
        • patterson6undefined
          patterson6 @jay_s_uk
          last edited by

          @jay_s_uk

          1. You were right with the out0 in. So i just bridged from the 24v. The bed works now. Thanks

          2. The M308 didnt work. Its not really on input number 1. Nothing is. I just put that in the config when i was in editor. Its just plugged into temp daughterboard then the z-prob is on IO3.

          3. Any idea for pin assignment on how to gcode it? My White led turns on fine when i do a M106. I just have to get the expansion board installed when it comes for the r,g,b. It will be plugged into those pinouts on the expansion board.
            ;******************** RGBW led strip on build area **********************
            M950 F4 C"out9" ; create white led on mainboard pin out9
            ;M950 F5 C"out6" ; create red led on expansion pin out 6
            ;M950 F6 C"out7" ; create green led on expansion pin out 7
            ;M950 F7 C"out8" ; create blue led on expansion pin out 8

          4. Thanks

          jay_s_ukundefined 1 Reply Last reply Reply Quote 0
          • Vetiundefined
            Veti
            last edited by

            @patterson6 said in help with config.g:

            M665 R316 L616.42 B215 H989.4 ; Set delta radius, diagonal rod length, printable radius and homed height
            M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them

            this is not the result of a delta calibration.

            also your config does not have a M501.
            So you have not run a pid tune. this will cause the observed errors on the bed.

            patterson6undefined 1 Reply Last reply Reply Quote 0
            • jay_s_ukundefined
              jay_s_uk @patterson6
              last edited by

              @patterson6 said in help with config.g:

              The M308 didnt work. Its not really on input number 1. Nothing is. I just put that in the config when i was in editor. Its just plugged into temp daughterboard then the z-prob is on IO3.

              P"spi.cs1"

              that specifies the temp daughterboard. they have 2 inputs, CS0 and CS1 so you will have to modify that line accordingly

              Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

              patterson6undefined 1 Reply Last reply Reply Quote 0
              • patterson6undefined
                patterson6 @fcwilt
                last edited by

                @fcwilt m122

                still having trouble with hotend

                ###########################################################
                === Diagnostics ===
                RepRapFirmware for Duet 3 MB6HC version 3.2 running on Duet 3 MB6HC v1.01 or later (standalone mode)
                Board ID: 08DJM-956L2-G43S8-6J9FD-3SJ6R-TB0AG
                Used output buffers: 1 of 40 (12 max)
                === RTOS ===
                Static ram: 149788
                Dynamic ram: 92524 of which 160 recycled
                Never used RAM 116360, free system stack 200 words
                Tasks: NETWORK(ready,199) ETHERNET(blocked,109) HEAT(blocked,297) CanReceiv(blocked,927) CanSender(blocked,371) CanClock(blocked,354) TMC(blocked,53) MAIN(running,1123) IDLE(ready,19)
                Owned mutexes:
                === Platform ===
                Last reset 00:01:10 ago, cause: software
                Last software reset at 2021-03-12 07:19, reason: User, GCodes spinning, available RAM 116360, slot 2
                Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
                Error status: 0x00
                Aux0 errors 0,0,0
                Aux1 errors 0,0,0
                MCU temperature: min 28.8, current 29.5, max 29.7
                Supply voltage: min 21.4, current 22.4, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
                12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
                Driver 0: position 971943, standstill, reads 1384, writes 14 timeouts 0, SG min/max 0/0
                Driver 1: position 971943, standstill, reads 1384, writes 14 timeouts 0, SG min/max 0/0
                Driver 2: position 971943, standstill, reads 1385, writes 14 timeouts 0, SG min/max 0/0
                Driver 3: position 0, standstill, reads 1385, writes 14 timeouts 0, SG min/max 0/0
                Driver 4: position 0, standstill, reads 1388, writes 11 timeouts 0, SG min/max 0/0
                Driver 5: position 0, standstill, reads 1388, writes 11 timeouts 0, SG min/max 0/0
                Date/time: 2021-03-12 07:20:19
                Slowest loop: 4.14ms; fastest: 0.05ms
                === Storage ===
                Free file entries: 10
                SD card 0 detected, interface speed: 25.0MBytes/sec
                SD card longest read time 2.3ms, write time 0.0ms, max retries 0
                === Move ===
                DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
                === MainDDARing ===
                Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
                === AuxDDARing ===
                Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
                === Heat ===
                Bed heaters = 2 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = 1 -1 -1 -1
                === GCodes ===
                Segments left: 0
                Movement lock held by null
                HTTP is idle in state(s) 0
                Telnet is idle in state(s) 0
                File is idle in state(s) 0
                USB is idle in state(s) 0
                Aux is idle in state(s) 0
                Trigger is idle in state(s) 0
                Queue is idle in state(s) 0
                LCD is idle in state(s) 0
                SBC is idle in state(s) 0
                Daemon is idle in state(s) 0
                Aux2 is idle in state(s) 0
                Autopause is idle in state(s) 0
                Code queue is empty.
                === Network ===
                Slowest loop: 6.76ms; fastest: 0.02ms
                Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
                HTTP sessions: 1 of 8

                • Ethernet -
                  State: active
                  Error counts: 0 0 1 0 0
                  Socket states: 5 2 2 2 2 0 0 0
                  === CAN ===
                  Messages queued 281, send timeouts 631, received 0, lost 0, longest wait 0ms for reply type 0, free buffers 48
                  ###############################################################
                  M98 P"config.g"
                  HTTP is enabled on port 80
                  FTP is disabled
                  TELNET is disabled
                  Warning: Sensor number 0 has not been defined
                  Tool 0 offsets: X0.00 Y0.00 Z0.00
                1 Reply Last reply Reply Quote 0
                • patterson6undefined
                  patterson6 @jay_s_uk
                  last edited by

                  @jay_s_uk

                  tried both 0 and 1 no go...

                  ;****************************************** Hotend ********************************************************************
                  M308 S1 P"spi.cs0" Y"rtd-max31865" ; configure sensor 0 as thermistor // Smart effector // pt 100 // on daugherboard
                  M950 H0 C"out1" T0 ; create nozzle heater output on out1 and map it to sensor 0
                  M307 H0 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                  M143 H0 S380 ; set temperature limit for heater 0 to 380C

                  jay_s_ukundefined 1 Reply Last reply Reply Quote 0
                  • jay_s_ukundefined
                    jay_s_uk @patterson6
                    last edited by

                    @patterson6 said in help with config.g:

                    @jay_s_uk

                    tried both 0 and 1 no go...

                    ;****************************************** Hotend ********************************************************************
                    M308 S1 P"spi.cs0" Y"rtd-max31865" ; configure sensor 0 as thermistor // Smart effector // pt 100 // on daugherboard
                    M950 H0 C"out1" T0 ; create nozzle heater output on out1 and map it to sensor 0
                    M307 H0 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                    M143 H0 S380 ; set temperature limit for heater 0 to 380C

                    you should be using H1 rather H0 otherwise the heater won't be created correctly for the tool

                    Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                    patterson6undefined 1 Reply Last reply Reply Quote 0
                    • patterson6undefined
                      patterson6 @Veti
                      last edited by

                      @Veti what do you mean its not a result of a delta calibration? what am i missing? Where would the M501 go? Yeah i didnt pid tune anything yet. Just trying to get it all working first. I am not great with Gcode.

                      Vetiundefined 1 Reply Last reply Reply Quote 0
                      • Vetiundefined
                        Veti @patterson6
                        last edited by

                        @patterson6
                        please read https://duet3d.dozuki.com/Wiki/Calibrating_a_delta_printer#Section_Auto_calibration

                        1 Reply Last reply Reply Quote 0
                        • patterson6undefined
                          patterson6 @jay_s_uk
                          last edited by

                          @jay_s_uk what does the S do in M308? reprap says sensor number but idk whats what. i was just matching the heater number. also still dont work. i tried both spi.cs1 and spi.cs0

                          ;HEATERSHEATERSHEATERSHEATERSHEATERSHEATERSHEATERSHEATERSHEATERSHEATERSHEATERSHEATERS

                          ;****************************************** Hotend ********************************************************************
                          M308 S3 P"spi.cs1" Y" rtd-max31865" ; define temperature sensor number 3 as a PT100 on the first port of a temperature daughter board plugged into mainboard
                          M950 H1 C"out1" T0 ; create nozzle heater output on out1 and map it to sensor 0
                          M307 H1 A498.0 C324.4 D4.2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                          M143 H1 S350 ; set temperature limit for heater 0 to 350C
                          ;****************************************** Chamber/Radiator heater ****************************************************
                          M308 S1 P"temp2" Y"thermistor" T50000 B3950 ; configure sensor 1 as thermistor on pin temp2 two sensors wired together
                          M570 H0 P10000 T15 ; Set heater fault detection for out 3, 1,000 second anomaly, 10c excursion
                          M950 H0 C"out3" T1 ; create chamber heater output on out3 and map it to sensor 1
                          M307 H0 A72.0 C71.5 D1.4 B0 S1.00 ; disable bang-bang mode for the chamber heater and set PWM limit
                          M141 H0 ; map chamber to heater 1
                          M143 H0 S90 ; set temperature limit for heater 1 to 90C
                          ;                          ***************************************** Bed Heater ****************************************************************
                          M308 S2 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 2 as thermistor on pin temp0
                          M950 H2 C"out0" T2 ; create bed heater output on out0 and map it to sensor 2
                          M307 H2 A183.1 C1561.5 D.7 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                          M140 H2 ; map heated bed to heater 2
                          M143 H2 S120 ; set temperature limit for heater 2 to 120C

                          1 Reply Last reply Reply Quote 0
                          • Phaedruxundefined
                            Phaedrux Moderator
                            last edited by

                            Here's what a sane setup for heaters looks like right out of the config tool.

                            ; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                           ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00                             ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                      ; map heated bed to heater 0
M143 H0 S120                                 ; set temperature limit for heater 0 to 120C
M308 S1 P"spi.cs0" Y"rtd-max31865"           ; configure sensor 1 as thermocouple via CS pin spi.cs0
M950 H1 C"out1" T1                           ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00                             ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                 ; set temperature limit for heater 1 to 280C
M308 S2 P"temp1" Y"thermistor" T100000 B3950 ; configure sensor 2 as thermistor on pin temp1
M950 H2 C"out2" T2                           ; create chamber heater output on out2 and map it to sensor 2
M307 H2 B0 S1.00                             ; disable bang-bang mode for the chamber heater and set PWM limit
M141 H2                                      ; map chamber to heater 2
M143 H2 S280                                 ; set temperature limit for heater 2 to 280C

                            I didn't duplicate your fans or tools though.

                            Z-Bot CoreXY Build | Thingiverse Profile

                            patterson6undefined 1 Reply Last reply Reply Quote 1
                            • patterson6undefined
                              patterson6 @Phaedrux
                              last edited by

                              @Phaedrux I found that at the bottom H1 was not declared under tools. So now my hotend pops up on dwc but under current for temp i am reading 2000.0c before it was just n/a. so then i changed the spi.cs0 to spi.cs1 even spi.cs2 even spi.cs3. nothing worked and all said 2000c. I checked all my connections and everything seems right.

                              The bright side my expansion board came today and i wired up the rgb led and found the extension on the out.6 pin just need an 1.out.6. So those work and i also added some more thermistors in extra. Pretty cool. I wish the trend chart was bigger.

                              ; Configuration file for Duet 3 (firmware version 3)

                              ;NETWORKNETWORKNETWORKNETWORKNETWORKNETWORKNETWORKNETWORKNETWORKNETWORKNETWORKNETWORK***NETWORK
                              M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
                              M586 P0 S1 ; enable HTTP
                              M586 P1 S0 ; disable FTP
                              M586 P2 S0 ; disable Telnet

                              ;GENERAL PREFERENCESGENERAL PREFERENCESGENERAL PREFERENCESGENERAL PREFERENCESGENERAL PREFERENCESGENERAL PREFERENCES
                              G90 ; send absolute coordinates...
                              M83 ; ...but relative extruder moves
                              M550 P"Duet 3" ; set printer name
                              M665 R316 L616.42 B215 H989.4 ; Set delta radius, diagonal rod length, printable radius and homed height
                              M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them

                              ;DRIVESDRIVESDRIVESDRIVESDRIVESDRIVESDRIVESDRIVESDRIVESDRIVESDRIVESDRIVESDRIVES
                              ;X,Y,Z stepper motors 23HM22-2804S https://www.omc-stepperonline.com/nema-23-bipolar-0-9deg-1-26nm-178-4oz-in-2-8a-2-5v-57x57x56mm-4-wires.html
                              ;E steper motor 42BYGHW811 on Nimble 2
                              M569 P0.0 S1 ; physical drive 0.0 goes forwards
                              M569 P0.1 S1 ; physical drive 0.1 goes forwards
                              M569 P0.2 S1 ; physical drive 0.2 goes forwards
                              M569 P0.3 S0 ; physical drive 0.3 goes backwards
                              M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping
                              M350 X64 Y64 Z64 E16 I1 ; configure microstepping with interpolation
                              M92 X640.00 Y640.00 Z640.00 E1775.00 ; set steps per mm
                              M566 X72000.00 Y72000.00 Z72000.00 E2400.00 ; set maximum instantaneous speed changes (mm/min)
                              M203 X330000.00 Y330000.00 Z330000.00 E216000.00 ; set maximum speeds (mm/min)
                              M201 X5400.00 Y5400.00 Z5400.00 E120.00 ; set accelerations (mm/s^2)
                              M906 X2800 Y2800 Z2800 E1800 I40 ; set motor currents (mA) and motor idle factor in per cent
                              M84 S30 ; Set idle timeout

                              ;AXIS LIMITSAXIS LIMITSAXIS LIMITSAXIS LIMITSAXIS LIMITSAXIS LIMITSAXIS LIMITSAXIS LIMITS***AXIS LIMITS
                              M208 Z0 S1 ; set minimum Z

                              ;ENDSTOPSENDSTOPSENDSTOPSENDSTOPSENDSTOPSENDSTOPSENDSTOPSENDSTOPSENDSTOPSENDSTOPS***ENDSTOPS
                              M574 X2 S1 P"io0.in" ; configure active-high endstop for high end on X via pin io0.in
                              M574 Y2 S1 P"io1.in" ; configure active-high endstop for high end on Y via pin io1.in
                              M574 Z2 S1 P"io2.in" ; configure active-high endstop for high end on Z via pin io2.in

                              ;Z-PROBEZ-PROBEZ-PROBEZ-PROBEZ-PROBEZ-PROBEZ-PROBEZ-PROBEZ-PROBEZ-PROBEZ-PROBEZ-PROBE
                              M558 P5 R0.4 C"io3.in+io3.out" H5 F500 T1500 ; set Z probe type to effector and the dive height + speeds
                              G31 P100 X0 Y0 Z4 ; set Z probe trigger value, offset and trigger height
                              M557 R215 S25 ; define mesh grid

                              ;****************************************** Hotend ********************************************************************
                              M308 S1 P"spi.cs0" Y"rtd-max31865" A"Hotend" ; define temperature sensor number 1 as a PT100 on the first port of a temperature daughter board plugged into mainboard
                              M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
                              M307 H1 A498.0 C324.4 D4.2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                              M143 H1 S280 ; set temperature limit for heater 0 to 280C
                              ;****************************************** Chamber/Radiator heater ****************************************************
                              M308 S2 P"temp2" Y"thermistor" A"Radiator" T50000 B3950 R2300 ; configure sensor 2 as thermistor on pin temp2 two sensors wired parallel
                              M570 H2 P10000 T15 ; Set heater fault detection for out 3, 1,000 second anomaly, 10c excursion
                              M950 H2 C"out3" T2 ; create chamber heater output on out3 and map it to sensor 2
                              M307 H2 A72.0 C71.5 D1.4 B0 S1.00 ; disable bang-bang mode for the chamber heater and set PWM limit
                              M141 H2 ; map chamber to heater 2
                              M143 H2 S90 ; set temperature limit for heater 2 to 90C
                              ;                              ***************************************** Bed Heater ****************************************************************
                              M308 S0 P"temp0" Y"thermistor" A"Bed" T100000 B3950 ; configure sensor 0 as thermistor on pin temp0
                              M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
                              M307 H0 A183.1 C1561.5 D.7 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                              M140 H0 ; map heated bed to heater 0
                              M143 H0 S120 ; set temperature limit for heater 2 to 120C

                              ;EXTRASEXTRASEXTRASEXTRASEXTRASEXTRASEXTRASEXTRASEXTRASEXTRASEXTRASEXTRASEXTRASEXTRAS
                              ;****************************************** Recirc air temp from hepa ****************************************************
                              M308 S5 P"temp3" Y"thermistor" A"Filter air temp" T100000 B3950 R2500 ; configure sensor 5 as thermistor on pin temp3
                              ;****************************************** MCU Temp *****************************************************************
                              M308 S6 Y"mcu-temp" A"MCU" ; configure sensor 6 as mcu temp on motherboard
                              ;****************************************** Air temp above effector ****************************************************
                              M308 S7 P"temp1" Y"thermistor" A"Effector air temp" T100000 B3950 ; configure sensor 6 as thermistor on pin temp3

                              ;COOLINGCOOLINGCOOLINGCOOLINGCOOLINGCOOLINGCOOLINGCOOLINGCOOLINGCOOLINGCOOLINGCOOLING
                              ;****************************************** Water pump for hotend ****************************************************
                              M950 F0 C"out5" Q500 ; create fan 0 on pin out5 and set its frequency
                              M106 P0 C"water pump " S1 H1:1 T35 ; set fan 0 name and value. Thermostatic control is turned on
                              ;****************************************** Chamber fan blowing on radiator*******************************************
                              M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency
                              M106 P1 C"radiator fan" S1 H1:1 T35 ; set fan 1 name and value. Thermostatic control is turned on
                              ;****************************************** Recirc/hepa filter fan ****************************************************
                              M950 F2 C"out7" Q500 ; create fan 2 on pin out7 and set its frequency
                              M106 P2 C"recirc/hepa fan" S1 H1:1 T35 ; set fan 2 value. Thermostatic control is turned on
                              ;****************************************** Berd air ******************************************************************
                              M950 F3 C"out4" Q500 ; create fan 3 on pin out4 and set its frequency
                              ;M106 P3 C"berd air" S1 H3 T35 ; set fan 3 value. Thermostatic control is turned on // Not needed at this time

                              ;LEDLEDLEDLEDLEDLEDLEDLEDLEDLEDLEDLEDLEDLEDLEDLEDLEDLEDLEDLED
                              ;***************************************** RGBW led strip on build area **********************************************
                              M950 F4 C"out9" ; create white led on mainboard pin out9
                              M950 F5 C"1.out6" ; create red led on expansion pin out 6
                              M950 F6 C"1.out7" ; create green led on expansion pin out 7
                              M950 F7 C"1.out8" ; create blue led on expansion pin out 8

                              ;TOOLSTOOLSTOOLSTOOLSTOOLSTOOLSTOOLSTOOLSTOOLSTOOLSTOOLSTOOLSTOOLSTOOLS***TOOLS
                              M563 P0 D0 H1 F0 ; define tool 0
                              G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                              G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                              ;MiscellaneousMiscellaneousMiscellaneousMiscellaneousMiscellaneousMiscellaneousMiscellaneousMiscellaneous
                              M501 ; load saved parameters from non-volatile memory

                              Phaedruxundefined 1 Reply Last reply Reply Quote 0
                              • Phaedruxundefined
                                Phaedrux Moderator @patterson6
                                last edited by

                                @patterson6 said in help with config.g:

                                i changed the spi.cs0 to spi.cs1 even spi.cs2 even spi.cs3. nothing worked and all said 2000c.

                                Photo of your wiring at the daughterboard?

                                Z-Bot CoreXY Build | Thingiverse Profile

                                patterson6undefined 1 Reply Last reply Reply Quote 0
                                • patterson6undefined
                                  patterson6 @Phaedrux
                                  last edited by

                                  @Phaedrux image1.jpeg image0.jpeg

                                  from the duet 2 to duet 3 the rest of the hardware has been untouched. Its been a year but i think the pt100 was working at that time.

                                  1 Reply Last reply Reply Quote 0
                                  • Phaedruxundefined
                                    Phaedrux Moderator
                                    last edited by

                                    Can you get a closer show of the daughterboard itself? Can you remove it and reseat it?

                                    Z-Bot CoreXY Build | Thingiverse Profile

                                    patterson6undefined 1 Reply Last reply Reply Quote 0
                                    • patterson6undefined
                                      patterson6 @Phaedrux
                                      last edited by

                                      @Phaedrux i removed it and checked the pins. seems to be seated properly. i have an extra smart effector i can try that i guess. if not i can buy another pt100. seems more like software.

                                      1 Reply Last reply Reply Quote 0
                                      • Phaedruxundefined
                                        Phaedrux Moderator
                                        last edited by

                                        Can you do this test on the daughterboard?

                                        https://duet3d.dozuki.com/Wiki/Connecting_PT100_temperature_sensors#Section_To_test_the_functionality_of_one_of_the_PT100_channels

                                        Z-Bot CoreXY Build | Thingiverse Profile

                                        patterson6undefined 2 Replies Last reply Reply Quote 0
                                        • patterson6undefined
                                          patterson6 @Phaedrux
                                          last edited by

                                          @Phaedrux pretty sure i can. give me a little bit

                                          1 Reply Last reply Reply Quote 0
                                          • patterson6undefined
                                            patterson6 @Phaedrux
                                            last edited by

                                            @Phaedrux so i found a 100ohm in my bin and wired it up. On channel P"spi.cs0". I am now getting 4.3c on the hotend. So i am going to put in the new smart effector when i can and order a new pt100 to be safe. thanks

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA