I could use some help
-
@mac said in I could use some help:
@fcwilt I'm still considering your M92 edit (moving it to ABOVE the M350 line). Can I simply copy and paste? Will the form renumber itself?
Yes, you can cut-and-paste a line of code with no problems.
Frederick
-
; Endstops M574 X1 S1 P"!io5.in" ; configure switch-type (e.g. microswitch) endstop for high end on X via pin !io5.in M574 Y1 S1 P"!io6.in" ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin !io6.in M574 Z1 S1 P"io2.in" ; configure Z-probe endstop for low end on Z -
@mac said in I could use some help:
; Endstops M574 X1 S1 P"!io5.in" ; configure switch-type (e.g. microswitch) endstop for high end on X via pin !io5.in M574 Y1 S1 P"!io6.in" ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin !io6.in M574 Z1 S1 P"io2.in" ; configure Z-probe endstop for low end on ZGreat!
Now execute the M119 again and let us know what is reports.
Frederick
-
@droftarts new M119: X not stopped, Y not stopped, Z at min stop, Z probe not stopped
-
@droftarts the print head's six inches off the bed
-
@mac said in I could use some help:
@droftarts new M119: X not stopped, Y not stopped, Z at min stop, Z probe not stopped
Great!
Notice that it says Z at min stop - was the Z endstop switch actually closed when you ran the M119?
Frederick
Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6
-
@mac said in I could use some help:
@droftarts the print head's six inches off the bed
I just asked a related question about the Z endstop switch.
Now you need to find a way to execute the M119 while both the X and Y endstop switches are closed - maybe with a bit of tape or a rubber band?
Frederick
Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6
-
@fcwilt the only thing that would close the z endstop is if the X axis came down and closed it.
-
@fcwilt wait, fcwilt? not droftarts? jeeze you guys are ganging up on me!
-
@mac said in I could use some help:
@fcwilt the only thing that would close the z endstop is if the X axis came down and closed it.
OK that's good to know.
If the white wire is actually connected to the NO connection of the Z endstop switch it should not be indicating Z at min stop.
Find a way to close the Z endstop switch and execute M119.
I want to see if it still reports Z at min stop or if it reports something different.
Frederick
Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6
-
@droftarts @fcwilt if we're going to work on this together, I need to know you two are in agreement before I do anything.
Do you both agree that I should tape X and Y closed? Then M119 again?
-
@mac said in I could use some help:
@fcwilt wait, fcwilt? not droftarts? jeeze you guys are ganging up on me!
No - it just gets confusing when posts overlap in time.
I'm typing, your typing, droftarts is typing - and things get a bit out of order - time wise.
Frederick
-
@mac said in I could use some help:
@droftarts @fcwilt if we're going to work on this together, I need to know you two are in agreement before I do anything.
Do you both agree that I should tape X and Y closed? Then M119 again?
Mac! You've cut me to the quick! Have you no faith in me!
I've only been doing this stuff for years.
Frederick
Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6
-
@fcwilt @droftarts I closed the z-endstop with my left finger, and hit M110 Send with my right finger. M119 reported Z: at end stop, Z probe: not stopped.
I'm not making this up, guys.
-
@fcwilt @droftarts I'm just trying to be respectful to Ian and you.
-
@mac I’m not able to reply promptly now, I’m away from my computer. @fcwilt knows what he’s doing, though please keep it simple, Frederick!
Ian
TronXY X5S with Duet 3 MB6HC and Roto toolboard : Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : Polargraph with Duet 2 WiFi
-
@droftarts said in I could use some help:
@mac I’m not able to reply promptly now, I’m away from my computer. @fcwilt knows what he’s doing, though please keep it simple, Frederick!
Ian
I try to keep it simple, I really do.
Frederick
-
; Drives M569 P0.0 S1 ; physical drive 0.0 goes forwards M569 P0.1 S1 ; physical drive 0.1 goes forwards M569 P0.2 S1 ; physical drive 0.2 goes forwards M569 P0.3 S1 ; physical drive 0.3 goes forwards M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping M92 X40.00 Y40.00 Z2000.00 E420.00 ; set steps per mm M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z600.00 E1200.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z200.00 E250.00 ; set accelerations (mm/s^2) M906 X600 Y600 Z600 E600 ; set motor currents (mA) M84 S0 ; Disable motor idle current reduction -
@mac M92 cut and pasted to before M350, board rebooted.
-
@fcwilt okay, I get it, let's continue on, shall we, Frederick?
