I could use some help

fcwilt

; Endstops
M574 X1 S1 P"!io5.in"                              ; configure switch-type (e.g. microswitch) endstop for high end on X via pin !io5.in
M574 Y1 S1 P"!io6.in"                              ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin !io6.in
M574 Z1 S1 P"io2.in"                                       ; configure Z-probe endstop for low end on Z

Great!

Now execute the M119 again and let us know what is reports.

Frederick

A Former User

@droftarts new M119: X not stopped, Y not stopped, Z at min stop, Z probe not stopped

A Former User

@droftarts the print head's six inches off the bed

fcwilt

@mac said in I could use some help:

@droftarts new M119: X not stopped, Y not stopped, Z at min stop, Z probe not stopped

Great!

Notice that it says Z at min stop - was the Z endstop switch actually closed when you ran the M119?

Frederick

fcwilt

@mac said in I could use some help:

@droftarts the print head's six inches off the bed

I just asked a related question about the Z endstop switch.

Now you need to find a way to execute the M119 while both the X and Y endstop switches are closed - maybe with a bit of tape or a rubber band?

Frederick

A Former User

@fcwilt the only thing that would close the z endstop is if the X axis came down and closed it.

A Former User

@fcwilt wait, fcwilt? not droftarts? jeeze you guys are ganging up on me!

fcwilt

@mac said in I could use some help:

@fcwilt the only thing that would close the z endstop is if the X axis came down and closed it.

OK that's good to know.

If the white wire is actually connected to the NO connection of the Z endstop switch it should not be indicating Z at min stop.

Find a way to close the Z endstop switch and execute M119.

I want to see if it still reports Z at min stop or if it reports something different.

Frederick

A Former User

@droftarts @fcwilt if we're going to work on this together, I need to know you two are in agreement before I do anything.

Do you both agree that I should tape X and Y closed? Then M119 again?

fcwilt

@mac said in I could use some help:

@fcwilt wait, fcwilt? not droftarts? jeeze you guys are ganging up on me!

No - it just gets confusing when posts overlap in time.

I'm typing, your typing, droftarts is typing - and things get a bit out of order - time wise.

Frederick

fcwilt

@mac said in I could use some help:

@droftarts @fcwilt if we're going to work on this together, I need to know you two are in agreement before I do anything.

Do you both agree that I should tape X and Y closed? Then M119 again?

Mac! You've cut me to the quick! Have you no faith in me!

I've only been doing this stuff for years.

Frederick

A Former User

@fcwilt @droftarts I closed the z-endstop with my left finger, and hit M110 Send with my right finger. M119 reported Z: at end stop, Z probe: not stopped.

I'm not making this up, guys.

A Former User

@fcwilt @droftarts I'm just trying to be respectful to Ian and you.

droftarts

@mac I’m not able to reply promptly now, I’m away from my computer. @fcwilt knows what he’s doing, though please keep it simple, Frederick!

Ian

fcwilt

@droftarts said in I could use some help:

@mac I’m not able to reply promptly now, I’m away from my computer. @fcwilt knows what he’s doing, though please keep it simple, Frederick!

Ian

I try to keep it simple, I really do.

Frederick

A Former User

@fcwilt @droftarts

; Drives
M569 P0.0 S1                                       ; physical drive 0.0 goes forwards
M569 P0.1 S1                                       ; physical drive 0.1 goes forwards
M569 P0.2 S1                                       ; physical drive 0.2 goes forwards
M569 P0.3 S1                                       ; physical drive 0.3 goes forwards
M584 X0.0 Y0.1 Z0.2 E0.3                           ; set drive mapping
M92 X40.00 Y40.00 Z2000.00 E420.00                 ; set steps per mm
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M566 X900.00 Y900.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z600.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z200.00 E250.00               ; set accelerations (mm/s^2)
M906 X600 Y600 Z600 E600                           ; set motor currents (mA)
M84 S0                                             ; Disable motor idle current reduction

A Former User

@mac M92 cut and pasted to before M350, board rebooted.

A Former User

@fcwilt okay, I get it, let's continue on, shall we, Frederick?

fcwilt

@mac said in I could use some help:

@fcwilt @droftarts I closed the z-endstop with my left finger, and hit M110 Send with my right finger. M119 reported Z: at end stop, Z probe: not stopped.

I'm not making this up, guys.

I know you are not. I have complete faith in you.

So as far as you can see M119 reports that same for the Z endstop switch regardless of it being pressed closed or not?

Interesting.

How about doing the same for the X and Y endstop switches. You can press just one at a time and execute the M119 for each one. It is not necessary to press them both at the same time.

What we want to verify is that M119 reports the correct thing for both states of the endstop switches, pressed and not pressed.

Frederick

A Former User

@fcwilt I just ran M119 again, it's reporting: X not stopped, Y not stopped, Z at min stop, Z probe not stopped.