Laser filament monitor
-
Please throw me on there too @dc42
-
You've probably got more than enough, but I'd test it too.
-
looking forward to an eta
-
Any kind of ETA on these new filament monitors?
-
I would be interested in testing one of those too, since I have several printers (CoreXY and Deltas, all with DUETs), use OpenSCAD myself and do Arduino Programming, I think I meet the conditions (Except living in Germany and not in the UK
) -
No word in a month? Hoping to hear something soon dc42
I'm putting in an end stop sensor based filament out sensor now in my CoreXY. Can anyone tell me if there is any point in a mechanical end stop board with a few support components and an LED, as opposed to just as simple switch? I find versions of both on Thingiverse. Does it matter with a Duet board?
-
@3dmntbighker The only thing that will matter between a simple switch and a switch with the LED is likely the high or low switching. For instance, I just installed a simple switch filament out sensor using a makerbot style endstop and it switches low. So you'll just need to set the relevant flag when you setup the command.
-
@phaedrux Thanks for the info. I wondered if a plain switch with no resisters anywhere could damage the Duet. Perhaps the inputs on the Duet are well protected and debounced?
-
@3dmntbighker said in Laser filament monitor:
@phaedrux Thanks for the info. I wondered if a plain switch with no resisters anywhere could damage the Duet. Perhaps the inputs on the Duet are well protected and debounced?
Yes, the endstop inputs are.
-
sorry for the delays. An update on testing is here:
https://forum.duet3d.com/topic/6092/laser-filament-monitor-test-results
-
This post is deleted! -
Hi to everyone who is beta testing this sensor. I built upon the geometry for the housing, and modified it so that the PTFE tube can't be pulled out , and also it is split-able so that you can remove the remnant filament after the tail end has been fed past the hob gear.
Video explaining it here: https://youtu.be/RmZ7aJYvWLc?t=7m40s
.stl file here: https://www.myminifactory.com/object/3d-print-splitable-duet-laser-filament-bracket-for-bowden-tube-printers-73781
-
@punamenon That's a clever design. Nice work. Love the videos too.
-
@punamenon said in Laser filament monitor:
Hi to everyone who is beta testing this sensor. I built upon the geometry for the housing, and modified it so that the PTFE tube can't be pulled out , and also it is split-able so that you can remove the remnant filament after the tail end has been fed past the hob gear.
I'm a bit confused about having the sensor after the extruder. So you are relying solely on filament movement detection for both jams and out of filament conditions? Obviously once the hob stops pushing you will always still have filament present in the sensor. Just no movement. Mine is direct drive so this is purely my curiosity. I want a QuadFusion CMYK head eventually, so my filament detection will be a whole different worm can.
-
@3dmntbighker said in Laser filament monitor:
@punamenon said in Laser filament monitor:
Hi to everyone who is beta testing this sensor. I built upon the geometry for the housing, and modified it so that the PTFE tube can't be pulled out , and also it is split-able so that you can remove the remnant filament after the tail end has been fed past the hob gear.
I'm a bit confused about having the sensor after the extruder. So you are relying solely on filament movement detection for both jams and out of filament conditions? Obviously once the hob stops pushing you will always still have filament present in the sensor. Just no movement. Mine is direct drive so this is purely my curiosity. I want a QuadFusion CMYK head eventually, so my filament detection will be a whole different worm can.
I would install it after the extruder too so it can read the texture made by the hob gear even with difficult to read materials.
-
One disadvantage of installing the filament monitor after the extruder drive is that there is an increased risk of filament dust contaminating the image sensor, especially after there has been a jam and some filament had been ground up.
Duet WiFi hardware designer and firmware engineer
Please do not ask me for Duet support via PM or email, use the forum
http://www.escher3d.com, https://miscsolutions.wordpress.com -
@dc42 said in Laser filament monitor:
One disadvantage of installing the filament monitor after the extruder drive is that there is an increased risk of filament dust contaminating the image sensor, especially after there has been a jam and some filament had been ground up.
A good point! What about a redesign so that when you split it apart, you can access the sensor with a cotton swab? Would repeated wiping damage the sensor?
-
@dc42 That is is true.....
-
@dc42 said in Laser filament monitor:
Today I've been trying out a laser optical sensor to see if it is accurate enough to use instead of the rotating magnet sensor we use in the beta test filament monitors. The good new is that in tests with several different filaments including black and transparent, first indications are that it works adequately, provided that the filament position is sufficiently well constrained. So we will go ahead with making prototypes. We may have a very small number (between 2 and 4) available for beta testers
This does however mean that production of filament monitors to the existing design is on hold until the prototypes are ready and tested, so that we can make an informed decision on which design to use.
The laser filament monitor would have a much simpler housing design. Basically it just needs to clamp PTFE tubes on the inlet and the outlet, to ensure that the filament is constrained to be in the centre of the field of view of the sensor.
Is the filament monitor available for purchase?
Thanks.
-
@celulari not yet
