I've watched it for a few weeks and haven't had any more mistakes.

replaced the cables and laid them along a different route

@fcwilt
thanks for the quick response ,I know enough for now

@fcwilt

the emergency stop runs on M24 pause during printing.

; Input/Output
M581 E2 S1 T1 C1 ; Pause - trigger1.g
M581 E3 S1 T2 C0 ; extrude 100mm - trigger2.g
M581 E4 S1 T3 C0 ; retract 100mm- trigger3.g
M581 E5 S1 T4 C0 ; G32- trigger4.g

; trigger1.g
M24
; trigger2.g
G1 E100 F300
; trigger3.g
G1 E-100 F300
; trigger4.g
G32

so it is explained a bit more clearly what I was planning

I have a question if it is possible.

I came across a link on how to use M581.
am currently using a duet 2 with rrf2 with an emergency stop on trigger9.g

it is possible to add more buttons to trigger.g folders i read

but is it right what i think ?

exemple :

button 1 extrude 100mm = trigger1.g G1 E100 F300
button 2 retract 100mm = trigger2.g G1 E-100 F300
button 3 G32 = trigger3.g Bed.g
emergency stop = trigger4.g M24

and what I read normal push buttons can be used,
pressing once is then going through trigger.g command

I hope it's easy to understand with google transstate

@dc42

I indeed had the wrong value I had F120 and had to be F1200

thanks for the quick response now it works.
And I'm one step further on my way

@phaedrux
i followed the steps,
but after sending G30 S-1 the nozzle digs into the bed and crooked the towers and effector .

the result after the G30 S-1 =
G30 S-1
Stopped at height -2.346 mm
(it doesn't stop at bed height but goes deeper)

it's even worse when I run a G29
I have added two movies of G30 S-1 command and G29

this is the G30 S-1 https://youtu.be/QhDlxRcwmeY

and this the G29 https://youtu.be/mDf4vhKAQFY

I found the problem

I checked everything from cables to bearings/belts, but it turned out that the lm8uu bearings of the carriages became stiff at some point and replaced them (that's why it worked on the head gravity )

but unfortunately I have another problem.

if I want to set the trigger height, it is located in the minus under the bed.
performed a few times G92 Z0 that the is Z0 but after home too high nozzle picks up paper -1.50

when I feed a G30 S-1 or G32 nozzle rams into bed
(G30 S-1 Stopped at height -2.786 mm)

in which direction should I going to search?

@dc42
thanks for the response

i'm going to reconnect and double check all cables and start with a clean config tool.

there must be something wrong with my setup,
I'll let here know if I find out anything but unfortunately I can only work on it during the weekends due to lack of time

@phaedrux

after sending M564 H0 and jog the print head I get an error

@phaedrux
i'm still in the startup phase of the delta can still look messy the config file

these are the files you asked for

I can't figure out why it only goes home after the printer is upside down, tried with and without arms but remains the same only home z.

I have not progressed as home all and pid tuning hotend and bed

bed (1).g config (1).g homedelta.g

sorry for the later response but it works it finds the limit switches, but this works differently if rr2.xx led on is not trigger and led off is triggered

but i have another question now

or should i ask a new question on the frorum ?

when I do home all only the z axis goes after home (x/y axis is stationary belt rattles minimally)

when I turn the delta upside down it does go to home all with the arms and smart effector mounted.

I found out after everything connected and wanted to calibrate the smart effector it does not work as it should be .
was working upside down because everything is mounted under the printer .