@jay_s_uk I finally got it through bossa. Weird that it wouldn't take the firmware any other way. Thanks for the help!
Best posts made by Phantom329
-
RE: Firmware installs but doesn't update
-
RE: How to change bed heater fault parameters?
@Phaedrux I tried changing the Hz from 1 to 1000 but no difference at all. I took a better video and also noted that the bed actually vibrates. It starts at around 55C and sometimes momentarily stops when above 60C (set at 60C) but immediately stops when I turn off the bed heat.
https://drive.google.com/file/d/1k6DX-6bAaiALDYou7UZGFRZKjEFxABVc/view?usp=sharing -
RE: Bad printing quality for unknown reason
@brotherchris Nope, I have the extruder and material set to 1.75mm.
Latest posts made by Phantom329
-
RE: Firmware installs but doesn't update
@jay_s_uk I finally got it through bossa. Weird that it wouldn't take the firmware any other way. Thanks for the help!
-
RE: Firmware installs but doesn't update
@jay_s_uk It seems my printer isn't connecting to the wi-fi after I tried installing 3.3. It also is still at version 3.1.1. I think It will be easier to pull the sd card at this point.
-
RE: Firmware installs but doesn't update
@jay_s_uk The 3.4.0 version also doesn't include the IAP. I had renamed Duet2_SDiap32_WiFiEth.bin to Duet2CombinedIAP.bin. I also tried Duet2CombinedFirmware.bin and no luck.
-
RE: Firmware installs but doesn't update
@jay_s_uk Thanks for the reply. Here is the output:
10/22/2022, 3:17:30 AM Connection established
10/22/2022, 3:17:17 AM M997 S0I can see that it tries to look for updates but doesn't do anything.
-
Firmware installs but doesn't update
I am trying to update from 3.1.1 to 3.4.4 but each time I try to install the firmware, it doesn't work. I uploaded "Duet2and3Firmware-3.4.4.zip" to /sys and clicked yes to install system files. It shows update progress, then restarts, but afterwards it still says version 3.1.1. It did update Duet web control to 3.4.4 though. I also checked M122 and it confirms firmware is still 3.1.1.
Duet Web Control 3.4.4
Board: Duet 2 WiFi (2WiFi)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.1.1 (2020-05-19b2)
Duet WiFi Server Version: 1.27 -
RE: Intermittent Z issues
@Phaedrux genius
Bed at 60C for the first layer, then off. I just have to get PID mode working then.
-
RE: Intermittent Z issues
@Veti I just checked the lead screws and there is very slight bend, like 0.5mm off the table. I don't think that would account for what I am seeing here. When I do get a good print, I think I can see the effect of that bend and its is not ridges, just very slight deformation every 4mm. The ridges in the above parts are usually 1.4mm apart but as you can see in the first part on the left, the ridges can be further apart.
-
RE: Intermittent Z issues
@Phaedrux Yes but I'm sure you noticed it is in bang-bang mode. I have an issue where the entire thing hums audibly so I can't use pwm.
-
RE: Intermittent Z issues
@Veti Yeah I know it looks like banding due to the lead screws, but how does that make sense when some parts or half a print comes out perfect? Also I greased my lead screws last month with ptfe grease and they are very low friction, can be back-driven easily. Also the pitch doesn't match the banding, the lead screws are 2mm pitch with 4 starts but the banding is not a multiple of that and changes between prints or sections of the print.
I didn't realize about the interpolation, I'll try changing it and see what happens.
-
RE: Why does infill cause my outlines to look bad?
Can you tell me exactly what you did to solve this? I am having what looks like a similar issue https://forum.duet3d.com/topic/21878/intermittent-z-issues