@phaedrux said in Toolboard 1.1 - Driver not present:
Please send an email to warranty@duet3d.com and CC your reseller. Include a link to this forum thread and the details of your original purchase. You'll receive a reply with a form to fill out.
Done. Thanks
Problem solved....
Is the driver.
I have another toolboard (never used, unboxed and installed) from the same reseller (filafarm.de).
Same wirings, same config, and works like a charm.
So the first Toolboard have a not working driver.
Can a moderator allow (give ok) reseller to replace this board?
@phaedrux Driver not "drive" stepper. I tried with 200°c and using M302
@rjenkinsgb Wirings are ok, tested with 2 different steppers that are working on other boards (duet boards)
Tried with 3.4.0 beta 7
After M122 b121 the driver info is like that:
"Driver 0: pos 6560, 656.0 steps/mm,ok, steps req 6560 done 6560"
But the stepper is not working at all.
@rjenkinsgb
Set stepper current to 100%
Set jerk, accelerations etc.
Hi,
I installed a original brand new Toolboard 1.1 in my new voron 2.4, equipped with Duet 3 mini 5.
The toolboard is perfectly working (fans, cartdrige ecc) but the stepper extruder is not working.
I checked with diagnostics and the is a "Not Present" about the driver 0.
This is the diagnostic
m122 b121
Diagnostics for board 121:
Duet TOOL1LC rev 1.1 or later firmware version 3.4.0beta6 (2021-11-06 11:56:11)
Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)
Never used RAM 2576, free system stack 2788 words
Tasks: Move(notifyWait,0.0%,153) HEAT(notifyWait,0.2%,113) CanAsync(notifyWait,0.0%,64) CanRecv(notifyWait,0.0%,77) CanClock(notifyWait,0.0%,64) ACCEL(notifyWait,0.0%,61) TMC(notifyWait,0.4%,67) MAIN(running,94.4%,350) IDLE(ready,0.0%,27) AIN(delaying,4.9%,142), total 100.0%
Last reset 00:09:54 ago, cause: power up
Last software reset data not available
Driver 0: pos 0, 656.0 steps/mm,not present, steps req 0 done 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0, step errors 0, maxPrep 0, maxOverdue 0, maxInc 0, mcErrs 0, gcmErrs 0
Peak sync jitter -4/6, peak Rx sync delay 213, resyncs 0/0, no step interrupt scheduled
VIN voltage: min 24.2, current 24.2, max 24.2
MCU temperature: min 30.3C, current 30.6C, max 35.0C
Last sensors broadcast 0x00000002 found 1 135 ticks ago, 0 ordering errs, loop time 0
CAN messages queued 10672, send timeouts 0, received 4800, lost 0, free buffers 37, min 37, error reg 0
dup 0, oos 0/0/0/0, bm 0, wbm 0, rxMotionDelay 0
Accelerometer detected: yes, status: 00
I2C bus errors 0, naks 0, other errors 0
This is my config
; Configuration file for Duet3 Mini5+ with Mini2+ expansion (firmware version 3.3 or newer)
; executed by the firmware on start-up
; General preferences
M80 C"pson" ; Turns on the ATX power supply
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M669 K1 ; Select CoreXY mode
M564 S1 H1 ; Forbid axis movements when not homed
;M918 P2 E4 F2000000 C30 R6 ; Fysetc 12864 display
; Wait a moment for the CAN expansion boards to start
G4 S2
; M575 P1 S1 B57600 ; enable support for PanelDue
; Network
M550 P"Voron V2.4" ; Set machine name
M552 S1 ; enable network
M587 S"xxxxx" P"xxxxxx" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; disable FTP
M586 P2 S0 ; disable Telnet
; --- Z Drive map ---
; _______
; | 1 | 2 |
; | ----- |
; | 0 | 3 |
; -------
; front
;
; (looking at the printer from the top)
; Drive directions
M569 P0 S1 D2 ; Z0
M569 P1 S0 D2 ; Z1
M569 P2 S1 D2 ; Z2
M569 P3 S0 D2 ; Z3
M569 P121.0 S0 ; Extruder
M569 P5 S1 D2 ; A
M569 P6 S1 D2 ; B
; Motor mapping and steps per mm
M584 X5 Y6 Z0:1:2:3 E121.0
M350 X16 Y16 Z16 E16 I1 ; Use 1/16 microstepping with interpolation everywhere
M92 X160 Y160 Z413 ; Set XY(0.9 deg motors)and Z(1.8deg motors)steps per mm
;M92 E432 ; BMG Extruder steps per mm
M92 E656 ; GALILEO Extruder steps per mm
; Drive currents
M906 X1250 Y1250 Z1400 E600 ; XYZ and E current
M906 I30 ; Idle current percentage
M84 S120 ; Idle timeout
; Accelerations and speed
M98 P"/macros/print_scripts/setup_printing.g"
; Axis travel limits
M208 X0 Y0 Z-8 S1 ; Set axis minima
M208 X300 Y306 Z275 S0 ; Set axis maxima
; Endstops
M574 X2 S1 P"io3.in" ; Xmax endstop on hall effect board
M574 Y2 S1 P"io1.in" ; Ymax endstop on hall effect board
M574 Z0 P"nil" ; No Z endstop
; Bed leveling
M671 X-65:-65:365:365 Y0:395:395:0 S20 ; Define Z belts locations (Front_Left, Back_Left, Back_Right, Front_Right)
M557 X25:275 Y25:275 P8:8 ; Define bed mesh grid (inductive probe, positions include the Y offset!)
;********************************************************************* Z PROBES
;SENSORE INDUTTIVO HOTEND
M558 K0 P8 C"121.io2.in" T18000 F120 H5 A5 S0.01 R0.2
G31 K0 P500 X0 Y25 Z2 ; Offset sensore
;MICROSWITCH Z
M558 K1 P8 C"^io6.in" T18000 F240:60 H2 A10 S0.005 R0.2
G31 K1 P500 X0 Y0 Z0.73 ; Z switch offset (if positive, greater value = lower nozzle. if negative, more negative = higher nozzle)
;*******************************************************************************
; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S115 ; set temperature limit for heater 0 to 100C
M308 S1 P"121.temp0" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin 121.temp0
M950 H1 C"121.out0" T1 ; create nozzle heater output on 121.out0 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
;M307 H1 B0
M143 H1 S280 ; set temperature limit for heater 1 to 280C
; Fans
M950 F0 C"121.out1" Q500 ; create fan 0 on pin 121.out1 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"121.out2" Q500 ; create fan 1 on pin 121.out2 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Misc
; M572 D0 S0.075 ; Pressure Advance
; M592 D0 A0.015 B0.0012 L0.2 ; Non-linear extrusion
; DAA tuning
M955 P121.0 I05 ; create accelerometer on P121.0
; M572 D0 S0.01 ; Pressure Advance
; M376 H10 ; Fade mesh out compensation over 10mm Z
M575 P1 S1 B57600 ; enable support for PanelDue
M501 ; load config-override.g
T0 ; select tool 0
What i'm doing wrong?
Thanks
Hi,
i connected my BTT 12864 Mini 1.0 to my duet 3 mini and the display seems not powered at all.
I connected it using EXP1 and EXP2 connectors.
A friend of mine has same behaviour with duet 3 mini and same kind of display.
we tested and noticed that on 5v pin of EXP1 there is no voltage
Thanks for any help
My paneldue wont show screensaver.
To force that i have to go to setup screen, set screensaver timeout and back to status screen.