Unfortunately, i was not so careful and I did not had the WWW folder on the SD card. That's why it did not work.
Best posts made by DR8
-
RE: Problem by connecting to duetwifi from browser
-
Configuring Slicer
Hi,
I don't know if here it's the best place to post this kind of topic but…. I'm wondering what slicer duet users use in order to achieve great prints. I was using Cura 2.6 And I had really nice looking prints. But because Cura 2.6 can't work with relative extrusion I installed the 3.0 one. The main advantage here is that I can use relative extrusion and also I can benefit from power outage protection feature. The problem is that with the same settings imported from Cura 2.6 into 3.0 I can't achieve the same quality of prints. They don't look bad but it's under my standard. Then I tried slic3r because it can support relative extrusion. Alot of tweaking but still, not awesome results. My main problems are small blobs and zits at the seam position. I did not had them in Cura 2.6. I have increased coasting and retraction extra prime( negative ) values, I tweaked the extrusion width and so on. Still not the results that I was expected.
So, what are you guys using as a slicer that support relative extrusion mode and maybe you are willing to post some values (pictures) also. Oh, BTW I'm using a bowden tube system 70cm long.
-
RE: Error: M24: Cannot resume while power voltage is low
Oh s..t,
Now I see the problem.I have another duet on other printer witch is on 24V. Jeez, I'm gonna loose my head one day. Thaks a lot.
Latest posts made by DR8
-
RE: I can no longer Load/Unload different filaments
That's right dc42. I have a CoreXY and defenetly it's a problem on DWC latest release. I did the downgrade and now it's working fine. Thanks
-
RE: I can no longer Load/Unload different filaments
I hve tried again and again. I think was the wak connection of my wifi router. Now I have uploaded and yes the topic problem was solved. But Now i have another one. When i want o move the head X+10mm the head goes -X and -Y direction. When I press Y+10 the head goes -X and +Y direction. My config.g is this
; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes forwards
M350 X64 Y64 Z64 E32 I1 ; Configure microstepping with interpolationI have tried:
M569 P0 S0 ; Drive 1 goes forwards
M569 P1 S0 ; Drive 2 goes forwardsM569 P0 S1 ; Drive 1 goes forwards
M569 P1 S0 ; Drive 2 goes forwardsM569 P0 S0 ; Drive 1 goes forwards
M569 P1 S1 ; Drive 2 goes forwardsM569 P0 S1 ; Drive 1 goes forwards
M569 P1 S1 ; Drive 2 goes forwards -
RE: I can no longer Load/Unload different filaments
it's says error on the bar where it should be 10 20 30 99% uploading. It uploads until 22 or so and then it shows error
-
RE: I can no longer Load/Unload different filaments
Oh, ok. Got it. So i have downloaded the latest firmware, server and web control from here https://github.com/dc42/RepRapFirmware/releases and when I try to upload and install the firmware via web interface I gor error. Why is that?
-
I can no longer Load/Unload different filaments
Hi,
Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 2.0(RTOS)RC5 (2018-05-22b1)
WiFi Server Version: 1.21
Web Interface Version: 1.21.1-RC4After the update on this firmware version I can't Load/Unload/Change filaments from my tool head. I have double checked and the right macros for the filaments are present in the "Filaments" folder. What can I do?
Thanks!
-
RE: Error: M24: Cannot resume while power voltage is low
Oh s..t,
Now I see the problem.I have another duet on other printer witch is on 24V. Jeez, I'm gonna loose my head one day. Thaks a lot.
-
RE: Error: M24: Cannot resume while power voltage is low
Yes I do. Here's the line from my config.g
M911 S20.5 R22.0 P"G91 M83 G1 Z3 E-3 F1000"
-
Error: M24: Cannot resume while power voltage is low
I have a duet wifi board with this configuration:
Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 2.0(RTOS)RC5 (2018-05-22b1)
WiFi Server Version: 1.21
Web Interface Version: 1.21.1-RC4I have installed a Runout filament sensor. It's an endstop. After it triggers, I insert a new filament and when to press Resume, I got this error:
Error: M24: Cannot resume while power voltage is low
The input voltage on the board is fluctuating between 11.7 and 12.2V. This error occur even if I intentionally press the Pause button.
-
RE: Problem by connecting to duetwifi from browser
Unfortunately, i was not so careful and I did not had the WWW folder on the SD card. That's why it did not work.
-
Problem by connecting to duetwifi from browser
So the problem that i have is that I can't connect with the IP adress to the duet board. I followed all the steps presented here: https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7?lang=en. Panel Due shows ,,Connected" Wifi module is connected to the access point........ IP adress:......... And when I type in the browser the specific IP adress i get no page found