@phaedrux You guys are awesome, I'll get that done as soon as I can!
Posts made by 3DMakerKid
-
RE: Duet 3 Mini 5+ Short to Ground Errorposted in Duet Hardware and wiring
-
RE: Duet 3 Mini 5+ Short to Ground Errorposted in Duet Hardware and wiring
@phaedrux It's now doing the same thing as before except just when the machine is powered on instead of after a print, and I changed nothing. So I'm not sure how much switching stealthchop off is going to help in this case.
-
RE: Duet 3 Mini 5+ Short to Ground Errorposted in Duet Hardware and wiring
@phaedrux Ok, I'm using sensorless homing on this printer and it looks like it can't be used with spreadcycle, as I found out here https://teamgloomy.github.io/sensorless.html .
-
RE: Duet 3 Mini 5+ Short to Ground Errorposted in Duet Hardware and wiring
@3dmakerkid actually, Does sensorless homing require stealthchop to be on? I can't seem to recall
-
RE: Duet 3 Mini 5+ Short to Ground Errorposted in Duet Hardware and wiring
@phaedrux Apologies
; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jun 30 2021 18:28:51 GMT-0400 (Eastern Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Hermione" ; set printer name ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet M587 I192.168.86.24 ; Drives M569 P0.0 S1 D3 V0 ; physical drive 0.0 goes forwards M569 P0.1 S0 D3 V0 ; physical drive 0.1 goes forwards M569 P0.2 S0 D3 V0 ; physical drive 0.2 goes forwards M569 P0.3 S0 ; physical drive 0.3 goes forwards M569 P0.4 S0 D3 V0 M584 X0 Y1 Z2:4 E3 ; two Z motors connected to driver outputs Z and E1 M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X100.00 Y100.00 Z400.00 E409.00 ; set steps per mm M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X15000.00 Y15000.00 Z300.00 E1200.00 ; set maximum speeds (mm/min) M201 X4000.00 Y4000.00 Z120.00 E250.00 ; set accelerations (mm/s^2) M906 X800 Y800 Z400 E600 I30 ; set motor currents (mA) and motor idle factor in per cent M84 X Y E0 S30 ; Set idle timeout M671 X-10:240 Y0:0 S3 ; leadscrews at left (connected to Z) and right (connected to E1) of X axis ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X240 Y205 Z210 S0 ; set axis maxima ; Endstops M574 X1 S3 ; configure sensorless endstop for low end on X M574 Y1 S3 ; configure sensorless endstop for low end on Y ; Z-Probe M558 P5 C"^io2.out" H2 F600 T6000 A3 ; Prusa PindaV2 Endstop M308 S2 P"temp2" A"Pinda V2" Y"thermistor" T100000 B3950 ; Prusa PindaV2 Thermistor G31 P1000 X-35.75 Y-18.7 Z.68 ; Nozzle offset M574 Z1 S2 ; Set Z axis endstop, controlled by probe M557 X0:180 Y0:180 P3 ; Define mesh grid for probing M376 H2 ; Fade height 5mm M564 S0 ; ; Heaters M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0 M307 H0 B0 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M307 H0 B0 R0.274 C426.1 D11.33 S1.00 V24.0 ; control parameters for H0 M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1 M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1 M307 H1 B0 R2.203 C200.0:140.4 D5.77 S1.00 V24.1 ; disable bang-bang mode for heater and set PWM limit M143 H1 S280 ; set temperature limit for heater 1 to 280C ; Fans M950 F0 C"out5" Q500 ; M106 P0 C"Part Cooling" S0 H-1 ; ; M950 F1 C"out6" Q500 ; M106 P1 C"Hotend" S1 H1 T45 ; ; ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined``` -
RE: Duet 3 Mini 5+ Short to Ground Errorposted in Duet Hardware and wiring
@phaedrux I am using stealthchop, M122 result:
=== Diagnostics === RepRapFirmware for Duet 3 Mini 5+ version 3.3 (2021-06-15 21:46:11) running on Duet 3 Mini5plus WiFi (standalone mode) Board ID: WB4NT-F096U-D65J0-40KM2-0Q03Z-ZJYMR Used output buffers: 3 of 40 (36 max) === RTOS === Static ram: 102724 Dynamic ram: 106092 of which 12 recycled Never used RAM 34876, free system stack 204 words Tasks: NETWORK(ready,15.0%,264) HEAT(delaying,0.0%,366) Move(notifyWait,0.1%,362) CanReceiv(notifyWait,0.0%,941) CanSender(notifyWait,0.0%,371) CanClock(delaying,0.0%,340) TMC(notifyWait,0.6%,115) MAIN(running,82.7%,426) IDLE(ready,0.7%,29) AIN(delaying,0.8%,274), total 100.0% Owned mutexes: WiFi(NETWORK) === Platform === Last reset 00:00:37 ago, cause: power up Last software reset at 2022-01-06 21:02, reason: User, GCodes spinning, available RAM 31628, slot 0 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a Error status: 0x00 MCU revision 3, ADC conversions started 37895, completed 37895, timed out 0, errs 0 Step timer max interval 1480 MCU temperature: min 15.6, current 20.2, max 20.4 Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0 Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 1959, writes 10, timeouts 0, DMA errors 0 Driver 1: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 1959, writes 9, timeouts 0, DMA errors 0 Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 1959, writes 9, timeouts 0, DMA errors 0 Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 1959, writes 9, timeouts 0, DMA errors 0 Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 1958, writes 10, timeouts 0, DMA errors 0 Driver 5: position 0, assumed not present Driver 6: position 0, assumed not present Date/time: 2022-01-07 17:26:56 Cache data hit count 72624651 Slowest loop: 6.64ms; fastest: 0.12ms === Storage === Free file entries: 10 SD card 0 detected, interface speed: 22.5MBytes/sec SD card longest read time 3.8ms, write time 0.0ms, max retries 0 === Move === DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === AuxDDARing === Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === Heat === Bed heaters = 0 -1, chamberHeaters = -1 -1 === GCodes === Segments left: 0 Movement lock held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 SBC is idle in state(s) 0 Daemon is idle in state(s) 0 Aux2 is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === CAN === Messages queued 338, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17), ts 189/0/0 Tx timeouts 0,0,188,0,0,148 last cancelled message type 4514 dest 127 === Network === Slowest loop: 27.87ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions HTTP sessions: 1 of 8 - WiFi - Network state is active WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.26 WiFi MAC address f0:08:d1:02:e6:60 WiFi Vcc 3.40, reset reason Power up WiFi flash size 2097152, free heap 24672 WiFi IP address 192.168.86.30 WiFi signal strength -47dBm, mode 802.11n, reconnections 0, sleep mode modem Clock register 00002002 Socket states: 0 2 0 0 0 0 0 0``` I have checked over wiring and even replaced motors several times. -
Duet 3 Mini 5+ Short to Ground Errorposted in Duet Hardware and wiring
Hello everyone, I have been running a Duet 3 MIni 5+ in my Bear for awhile and recently started getting this error, which doesn't sound very good to me.
This happens seemingly randomly when a print ends and if I turn the printer off for about a day and come back, it's fine. Often accompanied by this error is the X or Y axis refusing to move and making an intermittent ticking sound (X is plugged into driver 0 and Y to drive 1). I have heard that there was an issue with a revision of the board awhile back with this issue, so I'm not sure if maybe my board was a part of that batch? I'm running this version of firmware "RepRapFirmware for Duet 3 Mini 5+ 3.3 (2021-06-15)" according to DWC, which is version 3.3.0. -
RE: Motors not Moving and Getting Very Hotposted in Tuning and tweaking
@alankilian The motors aren't getting hot anymore for some reason, I did absolutely nothing to fix them. It's great that it seems to have fixed itself, but this happening randomly is not going to be a great thing... Also, my Y axis now will not sensorless home properly, even at a S value of 60, it's still just moving about a mm and thinking it's homed, otherwise, motion works great.
-
RE: Motors not Moving and Getting Very Hotposted in Tuning and tweaking
@alankilian Board is a Duet 3 Mini 5+, firmware is "RepRapFirmware for Duet 3 Mini 5+ 3.3 (2021-06-15)" according to DWC, this is kind of a new problem, I noticed my Z motors acting weird a week or so ago and getting extremely hot, but thought I had fixed it by correctly crimping the one motor wire, printed fine for a few days, and now this. I changed absolutely nothing before this print, except that this was a new gcode file that I had just sliced. Config.g and config-override.g are below.
d; Configuration file for Duet 3 Mini 5+ (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jun 30 2021 18:28:51 GMT-0400 (Eastern Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Hermione" ; set printer name ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0.0 S0 D3 V0 ; physical drive 0.0 goes forwards M569 P0.1 S1 D3 V0 ; physical drive 0.1 goes forwards M569 P0.2 S0 D3 V0 ; physical drive 0.2 goes forwards M569 P0.3 S0 ; physical drive 0.3 goes forwards M569 P0.4 S0 D3 V0 M584 X0 Y1 Z2:4 E3 ; two Z motors connected to driver outputs Z and E1 M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X100.00 Y100.00 Z400.00 E409.00 ; set steps per mm M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X9000.00 Y9000.00 Z600.00 E1200.00 ; set maximum speeds (mm/min) M201 X1250.00 Y750.00 Z120.00 E250.00 ; set accelerations (mm/s^2) M906 X600 Y800 Z400 E600 I30 ; set motor currents (mA) and motor idle factor in per cent M84 X Y E0 S30 ; Set idle timeout M671 X-10:240 Y0:0 S3 ; leadscrews at left (connected to Z) and right (connected to E1) of X axis ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X240 Y205 Z210 S0 ; set axis maxima ; Endstops M574 X1 S3 ; configure sensorless endstop for low end on X M574 Y1 S3 ; configure sensorless endstop for low end on Y M915 X S3 R1 F1 ; M915 Y S25 R1 F1 ; ; Z-Probe M558 P5 C"^io2.out" H2 F600 T6000 A3 ; Prusa PindaV2 Endstop M308 S2 P"temp2" A"Pinda V2" Y"thermistor" T100000 B3950 ; Prusa PindaV2 Thermistor G31 P1000 X-35.75 Y-18.7 Z.68 ; Nozzle offset M574 Z1 S2 ; Set Z axis endstop, controlled by probe M557 X0:180 Y0:180 P3 ; Define mesh grid for probing M376 H2 ; Fade height 5mm M564 S0 ; ; Heaters M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0 M307 H0 B0 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M307 H0 B0 R0.274 C426.1 D11.33 S1.00 V24.0 ; control parameters for H0 M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1 M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1 M307 H1 B0 R2.203 C200.0:140.4 D5.77 S1.00 V24.1 ; disable bang-bang mode for heater and set PWM limit M143 H1 S280 ; set temperature limit for heater 1 to 280C ; Fans M950 F0 C"out5" Q500 ; M106 P0 C"Part Cooling" S0 H-1 ; ; M950 F1 C"out6" Q500 ; M106 P1 C"Hotend" S1 H1 T45 ; ; ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not definedd; Configuration file for Duet 3 Mini 5+ (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jun 30 2021 18:28:51 GMT-0400 (Eastern Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Hermione" ; set printer name ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0.0 S0 D3 V0 ; physical drive 0.0 goes forwards M569 P0.1 S1 D3 V0 ; physical drive 0.1 goes forwards M569 P0.2 S0 D3 V0 ; physical drive 0.2 goes forwards M569 P0.3 S0 ; physical drive 0.3 goes forwards M569 P0.4 S0 D3 V0 M584 X0 Y1 Z2:4 E3 ; two Z motors connected to driver outputs Z and E1 M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X100.00 Y100.00 Z400.00 E409.00 ; set steps per mm M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X9000.00 Y9000.00 Z600.00 E1200.00 ; set maximum speeds (mm/min) M201 X1250.00 Y750.00 Z120.00 E250.00 ; set accelerations (mm/s^2) M906 X600 Y800 Z400 E600 I30 ; set motor currents (mA) and motor idle factor in per cent M84 X Y E0 S30 ; Set idle timeout M671 X-10:240 Y0:0 S3 ; leadscrews at left (connected to Z) and right (connected to E1) of X axis ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X240 Y205 Z210 S0 ; set axis maxima ; Endstops M574 X1 S3 ; configure sensorless endstop for low end on X M574 Y1 S3 ; configure sensorless endstop for low end on Y M915 X S10 R1 F1 ; M915 Y S25 R1 F1 ; ; Z-Probe M558 P5 C"^io2.out" H2 F600 T6000 A3 ; Prusa PindaV2 Endstop M308 S2 P"temp2" A"Pinda V2" Y"thermistor" T100000 B3950 ; Prusa PindaV2 Thermistor G31 P1000 X-35.75 Y-18.7 Z.68 ; Nozzle offset M574 Z1 S2 ; Set Z axis endstop, controlled by probe M557 X0:180 Y0:180 P3 ; Define mesh grid for probing M376 H2 ; Fade height 5mm M564 S0 ; ; Heaters M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0 M307 H0 B0 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M307 H0 B0 R0.274 C426.1 D11.33 S1.00 V24.0 ; control parameters for H0 M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1 M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1 M307 H1 B0 R2.203 C200.0:140.4 D5.77 S1.00 V24.1 ; disable bang-bang mode for heater and set PWM limit M143 H1 S280 ; set temperature limit for heater 1 to 280C ; Fans M950 F0 C"out5" Q500 ; M106 P0 C"Part Cooling" S0 H-1 ; ; M950 F1 C"out6" Q500 ; M106 P1 C"Hotend" S1 H1 T45 ; ; ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined -
Motors not Moving and Getting Very Hotposted in Tuning and tweaking
Ok so I started a print last night before I went out of the house, got back, print completed perfectly, but the printer was just sitting there with extremely hot motors (they made the PETG they were mounted on get soft). X Y, and one Z motor won't move, those are all burning hot to the touch, the other Z motor and the extruder motor work fine. The processor on the board is also hitting 70C while doing seemingly nothing, drivers are at around the same temp. All hot motors are also making a weird kind of "ticking" noise.
-
RE: Wifi Suddenly Stopped Working on Duet 3 Mini 5+posted in Duet Web Control
@phaedrux It was empty, wifi works fine when I copy everything over into a new config.g file, I did save config.g and reboot right before the wifi dropped. Looks like my psu is dead and not putting out 24V anymore too, completely unrelated though.
-
RE: Wifi Suddenly Stopped Working on Duet 3 Mini 5+posted in Duet Web Control
@3dmakerkid Am now using the config.g.bak file, but I'm getting under voltage warnings, even though there is no usb plugged in, it's on 24v power.
-
RE: Wifi Suddenly Stopped Working on Duet 3 Mini 5+posted in Duet Web Control
@jay_s_uk Looks like my entire config.g file is wiped for some reason? Sorry for taking so long to respond, lost the micro sd card for 3 hours.
-
RE: Wifi Suddenly Stopped Working on Duet 3 Mini 5+posted in Duet Web Control
@jay_s_uk Did it and it connected to wifi again.
-
RE: Wifi Suddenly Stopped Working on Duet 3 Mini 5+posted in Duet Web Control
@jay_s_uk No problem, got this back when I sent
M111 P14 S1[11:10:57:432] Debugging disabled for modules: Platform(0) Network(1) Webserver(2) GCodes(3) Move(4) Heat(5) DDA(6) Roland(7) Scanner(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) Display(15) LinuxInterface(16) CAN(17)␊ -
RE: Wifi Suddenly Stopped Working on Duet 3 Mini 5+posted in Duet Web Control
@jay_s_uk Ran that command and got this back, also is probably worth noting that the wifi module led is not on when I plugged it in via usb to my computer. I'm using CuteCom to connect to it if that matters.
[11:04:58:775] Debugging disabled for modules: Platform(0) Network(1) Webserver(2) GCodes(3) Move(4) Heat(5) DDA(6) Roland(7) Scanner(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) WiFi(14) Display(15) LinuxInterface(16) CAN(17)␊ ``` -
RE: Wifi Suddenly Stopped Working on Duet 3 Mini 5+posted in Duet Web Control
@jay_s_uk Nope, LED on the wifi module still doesn't come on.
-
RE: Wifi Suddenly Stopped Working on Duet 3 Mini 5+posted in Duet Web Control
@jay_s_uk All 4 of those LEDs are lit, LED status is blinking at 1hz as normal.