@Phaedrux I received my replacement board and now everything works properly. Thank you!
Best posts made by beachtec
RE: DWC only shows "retract" after reaching temps...
@Phaedrux Sorry about the R parameter... not sure about that one, but removed it anyway with no effect. The mappings are correct. The tool boards appear to be functioning correctly.
RE: RRF3 and Duet wifi + Duex5
I finally got back to the Railcore RRF3x issue and ended up pulling my boards... @Phaedrux mentioned the Duet WiFi was a cloned board... and I think that was the problem. I put in a genuine Duet board I had on hand it is has been working without a hitch. It is POSSIBLE that the very act of the board R&R corrected a wiring issue (intermittent connection) or the like... sometimes it is hard to tell if things are terminated properly. Overall a great learning... nothing gets me from rote knowledge to understanding faster than solving challenging problems - cheers.
p.s. thx to @JoergS5 too for the help!
Latest posts made by beachtec
RE: Looking for RRF 3.2 firmware (bin file) for Sammy board
@dc42! Thank you for uploading the Sammy Firmware. It was an easy install and it seems to be working.
BTW, it is not part of the ZIP files in the repository, you have to get it manually. Thank you again for everything you do here!!!
RE: Looking for RRF 3.2 firmware (bin file) for Sammy board
@droftarts Thank you for the help! I am printing it as we speak!
Looking for RRF 3.2 firmware (bin file) for Sammy board
I did look at the GitHub post about compiling your own firmware for the Sammy board (purchased from Fliastruder, with the boot loader pre-installed) but either the links are dead or I am faced with the realization I need to spend several months going blind learning how to use the listed dev tools to do something one of you guys has already done, or can do in 15 minutes.
That said, I believe a good call for help in in order!
I am using RRF 3.2 at the moment but will gladly upgrade to the latest stable (3.2.2?) to be able to experiment with this thing.
In exchange, if you help and forward me an address... I will send you a car Hahaha - Thank You!!!
RE: Tool Board error "Assumed Not Present"
@Phaedrux Thank you.
No damage to the board... New (but purchased several months back) .
1/28/2021, 5:23:21 PM M122 === Diagnostics === RepRapFirmware for Duet 3 MB6HC version 3.2 running on Duet 3 MB6HC v1.01 or later (SBC mode) Board ID: 08DJM-956L2-G43S8-6J9F6-3SJ6P-KA02G Used output buffers: 1 of 40 (14 max) === RTOS === Static ram: 149788 Dynamic ram: 63292 of which 76 recycled Never used RAM 145676, free system stack 128 words Tasks: Linux(blocked,101) HEAT(blocked,296) CanReceiv(blocked,817) CanSender(blocked,352) CanClock(blocked,352) TMC(blocked,19) MAIN(running,1202) IDLE(ready,19) Owned mutexes: HTTP(MAIN) === Platform === Last reset 00:15:51 ago, cause: power up Last software reset at 2021-01-27 20:22, reason: User, Move spinning, available RAM 145492, slot 1 Software reset code 0x0004 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task Linu Freestk 0 n/a Error status: 0x00 Aux0 errors 0,0,0 Aux1 errors 0,0,0 MCU temperature: min 14.2, current 34.4, max 34.6 Supply voltage: min 23.8, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes 12V rail voltage: min 12.1, current 12.2, max 12.2, under voltage events: 0 Driver 0: position 48000, standstill, reads 10707, writes 20 timeouts 0, SG min/max 0/318 Driver 1: position 0, standstill, reads 10707, writes 20 timeouts 0, SG min/max 0/315 Driver 2: position 704000, standstill, reads 10708, writes 19 timeouts 0, SG min/max 0/88 Driver 3: position 0, standstill, reads 10708, writes 20 timeouts 0, SG min/max 0/169 Driver 4: position 0, standstill, reads 10708, writes 20 timeouts 0, SG min/max 0/183 Driver 5: position 0, standstill, reads 10708, writes 20 timeouts 0, SG min/max 0/191 Date/time: 2021-01-28 17:23:22 Slowest loop: 147.61ms; fastest: 0.04ms === Storage === Free file entries: 10 SD card 0 not detected, interface speed: 37.5MBytes/sec SD card longest read time 0.0ms, write time 0.0ms, max retries 0 === Move === DMs created 125, maxWait 59073ms, bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves 28, completed moves 28, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 1], CDDA state -1 === AuxDDARing === Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === Heat === Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 === GCodes === Segments left: 0 Movement lock held by null HTTP* is doing "M122" in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger* is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 SBC is idle in state(s) 0 Daemon is idle in state(s) 0 Aux2 is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === CAN === Messages queued 3756, send timeouts 0, received 22295, lost 0, longest wait 2ms for reply type 6031, free buffers 48 === SBC interface === State: 4, failed transfers: 0 Last transfer: 2ms ago RX/TX seq numbers: 33136/33136 SPI underruns 0, overruns 0 Number of disconnects: 0, IAP RAM available 0x2c8a8 Buffer RX/TX: 0/0-0 === Duet Control Server === Duet Control Server v3.2.0 Code buffer space: 4096 Configured SPI speed: 8000000 Hz Full transfers per second: 0.91 Maximum length of RX/TX data transfers: 3092/712
; Duet 3 hardware, 6HC Main board plus 2 tool boards ; Printer name is set on the R Pi. ; Networking ;;;M552 P192.168.1.2 S1 ; Use Ethernet with a static IP ;;;M553 P255.255.255.0 ; Netmask ;;;M554 192.168.1.3 ; Gateway M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Debugging M111 S0 ; Debug off M929 P"eventlog.txt" S1 ; Start logging to file eventlog.txt ; General Preferences M555 P2 ; Set Marlin-style output G21 ; Set dimensions to millimetres G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Kinematics M669 K1 ; CoreXY mode ; Leadscrew locations (really, kinematic coupling locations) extracted from CAD model assuming back right build plate corner is (0, 0) M671 X300:5:152.5 Y316:316:-14 S10 ; Front Left: (300, 316) | Front Right: (5, 316) | Back: (-14, 152.5) ; Axis to driver mapping M569 P0 S0 D2 ; Drive 0 direction | X stepper M569 P1 S0 D2 ; Drive 1 direction | Y Stepper M569 P2 S0 ; Drive 2 direction | U Tool Changer Lock M569 P3 S0 D2 ; Drive 3 direction | Front Left Z M569 P4 S0 D2 ; Drive 4 direction | Front Right Z M569 P5 S0 D2 ; Drive 5 direction | Back Z M569 P20.0 S0 D2 ; set tool 2 extruder direction on Hermera Toolboards M569 P21.0 S0 D2 ; set tool 3 extruder direction on Hermera Toolboards M584 X0 Y1 U2 Z3:4:5 ; X and Y for CoreXY. U for toolchanger lock. Z has three drivers for kinematic bed suspension. M584 E20.0:21.0 ; Set Hermera extruder drives up on Hermera Toolboards ; Axis and motor configuration M350 X16 Y16 I1 ; Set 16x microstepping for axes. Use interpolation. M350 U4 I1 ; Set 4x for toolchanger lock. Use interpolation. M350 Z16 I1 ; Set 16x microstepping for axes. Use interpolation. M350 E16:16 I1 ; Motor Configurations M906 X2500 Y2500 Z1000 E1250 I30 ; Motor currents (mA) and Idle percentage M906 U900 I60 ; Motor currents (mA) and Idle percentage M201 X600 Y600 Z10 E1000 U1000 ; Accelerations (mm/s^2) M203 X25000 Y25000 Z400 E4000 U10000 ; Maximum speeds (mm/min) M566 X700 Y700 Z2 E3000 U200 ; Maximum jerk speeds mm/minute ;M92 X200 Y200 ; Steps/mm for X,Y with 16 tooth pulleys (preferred). M92 X160 Y160 ; Steps/mm for X,Y with 20 tooth pulleys. M92 Z3200 ; Steps/mm for Z - TR8*4 / 0.9 deg stepper M92 U11.429 ; Steps/mm for tool lock geared motor. M92 E837:837 ; Extruder - 0.9 deg/step ; Endstops and probes M574 X1 S1 P"io1.in" ; Set homing switch configuration X1 = low-end, S1 = active-high (NC) M574 Y1 S1 P"io2.in" ; Set homing switch configuration Y1 = low-end, S1 = active-high (NC) M574 U1 S1 P"io3.in" ; Set homing switch configuration U1 = low-end, S1 = active-high (NC) ;M574 Z1 S1 P"!io4.in" ; Set homing switch configuration Z1 = low-end, S1 = active-high (NC). This is used for tool probing, not actual Z height. M558 K0 P5 C"io4.in" H8 A5 T6000 S0.02 ; Z probe - Set the height of the bed when homing G28. Combined with content of bed.g as invoked by G32, levels bed. Also used for Mesh. ; P5 = Switch, NC ; C = Input Connector ; Hn = dive height ; A bigger dive height prevents a situation where the bed is out of alignment by more than the dive height ; on any corner, which can crash the hot-end into the bed while moving the head in XY. ; Probing speed and travel speed are similarly reduced in case the Z probe isn't connected properly (or ; disconnects later after moving to a point) giving the user more time to stop. ; An = Number of times to probe each point. ; Tnnn = Travel speed between probe points. ; Snnn = Tolerance when probing multiple times. Two readings inside this window and we move on. ;M558 K1 P5 C"!io4.in" ; create probe #1 for use with M585, active low ; Set axis software limits and min/max switch-triggering positions. Adjust such that (0,0) lies at the lower left corner of the build plate. M208 X-5:305 Y-10:365 Z-0.5:220 M208 U0:180 ; Temperature sensors M308 S0 P"0.temp0" Y"thermistor" T10000 B3984 A"Bed" ; Bed sensor M308 S1 P"20.temp0" Y"thermistor" T100000 B4725 C7.06e-8 ; Hemera sensors and heaters M308 S2 P"21.temp0" Y"thermistor" T100000 B4725 C7.06e-8 ; Hemera sensors and heaters ; Heaters M950 H0 C"0.out0" T0 ; Bed. H = Heater 0, C is output for heater itself, T = Temperature sensor (defined above) M950 H1 C"20.out0" T1 ; Hemera sensors and heaters M950 H2 C"21.out0" T2 ; Hemera sensors and heaters ; Further setup for bed M143 H0 S130 ; set temperature limit for heater 0 to 130C M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 ; Default heater model M307 H0 A140 C252 D0.7 S1.0 V24.0 B0 ; Tuned Bed Heater Paramaters, same as report above, also B0 to turn off bang-bang M307 H1 A452 C235 D11 V24 M307 H2 A452 C235 D11 V24 ; Default Bed Heater Parameters, before tuning / if config-override.g is missing ; Calibration 28 Oct 2019 ;Heater 0 model: gain 139.6, time constant 252.2, dead time 0.7, max PWM 1.00, calibration voltage 24.5, mode PID ;Computed PID parameters for setpoint change: P468.8, I35.594, D225.7 ;Computed PID parameters for load change: P468.8, I136.631, D225.7 ; Hemera fans M950 F5 C"20.out2+out2.tach" ; Tool 0 hot end fan with tacho M950 F6 C"20.out1" ; Tool 0 print cooling fan, no tacho M950 F7 C"21.out2+out2.tach" ; Tool 1 hot end fan with tacho M950 F8 C"21.out1" ; Tool 1 print cooling fan, no tacho M106 P5 S255 H1 T50 ; Tool 0 hot end M106 P6 S0 ; Tool 2 PCF M106 P7 S255 H2 T50 ; Tool 1 hot end M106 P8 S0 ; Tool 3 PCF ; Tool definitions M563 P0 S"Tool 0" D0 H1 F5 ; Px = Tool number, Dx = Drive Number (start at 0, after movement drives), H1 = Heater Number, Fx = Fan number print cooling fan G10 P0 S210 R160 ; Set tool 0 operating and standby temperatures(-273 = "off") M572 D0 S0.1 ; Set pressure advance on M563 P1 S"Tool 1" D1 H2 F6 ; Px = Tool number, Dx = Drive Number (start at 0, after movement drives), H1 = Heater Number, Fx = Fan number print cooling fan G10 P1 S210 R160 ; Set tool 1 operating and standby temperatures(-273 = "off") M572 D1 S0.1 ; Set pressure advance on M98 P"/sys/Toffsets.g" ; Set tool offsets from the bed. In separate file so test macro can invoke. ; Set up the dock indicator switches on the Hemera tools. These are wired NO so invert the pin (commented out for now). ;M950 J2 C"20.^!io0.in" ; GpIn 2 = tool 0 dock switch ;M950 J3 C"21.^!io0.in" ; GpIn 1 = tool 1 dock switch M575 P1 B57600 S1 ;M98 P"config-user.g" ; Load custom user config if one exists. ;M501 ; Load saved parameters from non-volatile memory ;G29 S1
Tool Board error "Assumed Not Present"
Hello! What does "Driver 0: position 1263870, 837.0 steps/mm, assumed not present" in board 20 mean??? Everything else works but the extruder drive motor is NoOp. This is the 122 dump...
1/27/2021, 6:41:37 PM M122 B21 Diagnostics for board 21: Duet TOOL1LC firmware version 3.2 (2021-01-05) Bootloader ID: not available Never used RAM 4052, free system stack 38 words HEAT 90 CanAsync 89 CanRecv 83 TMC 54 MAIN 214 AIN 64 Last reset 01:15:48 ago, cause: power up Last software reset data not available Driver 0: position 167400, 837.0 steps/mm, standstill, SG min/max 0/496, read errors 0, write errors 0, ifcnt 43, reads 46048, writes 43, timeouts 0, DMA errors 0 Moves scheduled 10, completed 10, in progress 0, hiccups 0 No step interrupt scheduled VIN: 24.1V MCU temperature: min 18.3C, current 34.0C, max 36.0C Ticks since heat task active 229, ADC conversions started 4543552, completed 4543551, timed out 0 Last sensors broadcast 0x00000004 found 1 233 ticks ago, loop time 0 CAN messages queued 54464, send timeouts 0, received 59106, lost 0, free buffers 36 1/27/2021, 6:41:17 PM M122 B20 Diagnostics for board 20: Duet TOOL1LC firmware version 3.2 (2021-01-05) Bootloader ID: not available Never used RAM 4052, free system stack 44 words HEAT 86 CanAsync 89 CanRecv 83 TMC 60 MAIN 208 AIN 64 Last reset 01:15:28 ago, cause: power up Last software reset data not available **Driver 0: position 1263870, 837.0 steps/mm, assumed not present** Moves scheduled 18, completed 18, in progress 0, hiccups 0 No step interrupt scheduled VIN: 23.7V MCU temperature: min 13.1C, current 26.1C, max 26.6C Ticks since heat task active 4, ADC conversions started 4524398, completed 4524397, timed out 0 Last sensors broadcast 0x00000002 found 1 7 ticks ago, loop time 0 CAN messages queued 54219, send timeouts 0, received 58848, lost 0, free buffers 36
RE: Weird Behavior Duet 3 / RRF 3.2
I copied this syntax from the article by @dc42 "Converting the E3D Tool Changer to Duet 3 with Hemera Tools (Part 2). In his piece, he was replacing 2 extruders with 2 Hemera's with Tool Boards.
Is this incorrect?
; Hemera motors M569 P22.0 S0 ; set tool 2 extruder direction M569 P23.0 S0 ; set tool 3 extruder direction M584 E3:4:22.0:23.0 ; set extruder drives
RE: Weird Behavior Duet 3 / RRF 3.2
@dc42 Thank you, I did locate the intermittent switch. I should have looked at as a separate issue but I am rather frustrated at the core issue and foolishly assumed they were related.
The core problem I am having is when I am using the Hemera's with the tool boards. If I select a tool, the Hemera heats up as expected. Using the web interface, I select "Extrude/Retract" and specify a set length and feedrate and select it, but instead of the extruder motor running as expected, Drive 1 on the 6HC board runs, causing the entire tool assembly to move diagonally. If I select the opposite, say retract instead of extrude, the same motor runs the opposite way.
I tried to run Tool1 last night and the lock motor ran instead... rather unfortunately. Aside from being quite frustrating, I hate having to have to bother folks in the form with this stuff, but I am now short on ideas and fingernails
RE: Error M587:Failed to add SSID to remembered list.
Hello @Hiroaki... I have had this issue myself a few times. The advice here did solve it; but I had to do it a couple of times. Re-flashing the firmware more than once might be necessary. I also found that in BOSSA, using the setting "erase all" seemed to yield the best results. Good luck to you!