Posts made by cgcafer

Hi,
V2 Board and 5"LCD works with this firmware.
Problem solved,
Many Thanks

Hi,
My on screen keyboard problem solved, many thanks.
I will waiting V2 board 5" LCD solution

https://drive.google.com/file/d/1JUmpmnN39RU9hgvowxu67gGC0sFneF2J/view?usp=sharing
https://drive.google.com/file/d/1BLFRYAHmChkUitGM5Tn8wXyLXaf9cAyy/view?usp=sharing
All V3 same result

Thanks for your answer, i have also another problem that is about V2 board and 5"LCD.
it has no problem with V1.24 but not V3.2.2. It seems to like about lcd timing problem.

Hi,
I have a problem about on screen keyboard. I pressed any letter but no any visible feedback. When i close and re open keyboard all pressed letter can visible.
My board V3 and 7"

Thank you, now things get much more mixed up for me.

Hi,
I think I checked all the directives in the buildinstruction.md file, but I still have a problem. The "Build All" operation is completed without any errors. But no Duet2CombinedFirmware.bin file is created, only makefiles (*.mk) .
Where am I making mistakes, or what is missing?

@dc42 said in Firmware 2.0RC6 and 1.21.1RC6 released:

Were you able to access the SD card via DWC or PanelDue after the error occurred, without either resetting the Duet or sending M21?

I sent M122 from DWC after that shutdown all system so i didn't test it.

Hi All,
There was a problem when i use RC6 without any problem. When it printing i changed M566 value from paneldue then error message appeared and printing stopped.
Old value was M566 X800 Y800
New value was M566 X1200 Y1200

and M122 result,
12:17:52
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.0(RTOS)RC6 running on Duet WiFi 1.02 or later + DueX2
Board ID: 08DDM-9FAM2-LW4S8-6JTDG-3SJ6P-1MXBY
Used output buffers: 1 of 20 (13 max)
=== RTOS ===
Static ram: 28380
Dynamic ram: 96516 of which 0 recycled
Exception stack ram used: 420
Never used ram: 5756
Task NETWORK ready, free stack 324
Task HEAT blocked, free stack 1256
Task MAIN running, free stack 3560
=== Platform ===
Last reset 00:39:03 ago, cause: software
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 5816 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 8
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 32.2ms
MCU temperature: min 23.5, current 25.6, max 26.3
Supply voltage: min 0.9, current 24.0, max 24.2, under voltage events: 1, over voltage events: 0
Driver 0: standstill, SG min/max 365/683
Driver 1: standstill, SG min/max 0/1023
Driver 2: standstill, SG min/max 0/616
Driver 3: standstill, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Expansion motor(s) stall indication: no
Date/time: 2018-06-05 12:17:51
Slowest loop: 53.39ms; fastest: 0.06ms
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 121, MaxWait: 141786ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 29
Bed compensation in use: mesh
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 38.73ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.21
  WiFi MAC address 5c:cf:7f:a4:04:fe
  WiFi Vcc 3.36, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 15528
  WiFi IP address 10.0.0.25
  WiFi signal strength -58dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0
  === Expansion ===
  DueX I2C errors 0

Conditional g code can be useful especially for config.g. For example you can configure it depends on 3d printer, laser or cnc mode.

Hi,
I guess you've checked it over and over again until now. but I want to ask you one more time. how are the spaces between the rod and the bearings(bushing) mechanically? and if you are using elastic coupling and the load is too much, you may have problems.

Hi,
Thank you for your answer, tomorrow morning i will check it. Which version it should be?

Hi,
I am using RTOS version and generally no problem. Today i add relay unit for controlling 24V line (M80 and M81).
It is work but when i first start the printer 7" Panel due still connection state, if i send M80 from DWC then paneldue's state change to idle. After that paneldue can send M80 and M81 without any problem.

Is this firmware problem or i made any mistake?
Thanks,

Hi David,
This is the first run for me with RTOS, here you can find M122 result

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.0(RTOS)alpha1 running on Duet WiFi 1.02 or later
Board ID: 08DAM-9K9K2-NGNSN-6J9D6-3S46J-TPSMJ
Used output buffers: 2 of 40 (31 max)
=== RTOS ===
Static ram: 28484
Dynamic ram: 97188 of which 0 recycled
Exception stack ram used: 384
Never used ram: 5016
Task NETWORK ready, free stack 316
Task HEAT blocked, free stack 572
Task MAIN running, free stack 3808

I have another duet wifi and i updated RTOS firmware via DWC. After that duet wifi continuously reset

NOTE : Duet wifi board connected usb port and no any other connection (any motor, any sensor etc only duet wifi board v1.02)

Yes you are right 1.21
laser led turned on and off(like flashing) in 3-5 seconds
I was tried M552 S1 but no success.

Hi David,
This morning i updated, after that i can't connect via wifi and fan2 (now it is connected to laser head) it was flashed one in 3-5 second.

I was busy so after that i reinstall to regular version (1.12). If you want to diagnostic i can try it again.
Thanks
Cafer

Hi resam,
i have problem by using LaserWeb 4.0.991. I am using M452 and M3 M5 command. Some laser On-Off doesn't work when i use "Laser Fill Path" strategy. So the result has a lot of missing lines.
Do you have same problem or have you any suggestion.

Note :I use Inkscape addin (J Tech Photonic Laser Tool) without any problem.
Thanks
Cafer

Hi Danny,
I am mechanical Engineer and i have my own job that we make plastic injection mold. So we have 3 EDM machines and CNCs..
I used several CAM programs and now i use PowerMill. I just build my 3D printer with duetwifi , duex2 and paneldue 7". I am suffering from slicers because i can't control everything but I get used to it all day.
I developed all electric plastic injection machine controller by using PIC32MZxx now it is testing phase.
Cafer

Hi Peter247,
When you print round shape something that is 2 or 3 mm diameter, if circularity is good probably your maximum instantaneous speed changes (M566) value is right, but if not you should decrease the value.