Best posts made by charliedrums

After many weeks of testing, I figured out the problem. I started re-wiring every cable to eliminate any problem with the harnesses. Once I got to the power from the Mainboard 6HC to the tool distribution board. I measured the power from this cable with a multimeter and everything was reading normal. For some reason once I rewired this harness everything seems to be working now.

I’ve done dozens of 20–50-hour prints with no problem so far. Updating this post in case someone is having the same issue. Check the power from the main board to the tool distribution board.

@phaedrux Reprinted the housing and assembled everything. My agc was a little low so I had to take it apart an shim it with a piece of paper. Now I have an agc within the range (59)

Duet3D rotating magnet filament monitor v3 on pin 121.io1.in, enabled, sensitivity 24.84mm/rev, allow 35% to 130%, check printing moves every 15.0mm, version 3, mag 131 agc 59, measured sensitivity 25.12mm/rev, min 98% max 101% over 781.5mm

I'm wating on some filament to start a couple of 15 to 17 hour prints to see if I keep getting the issue.

O and I updated to the RRF3.4 stable release.

Just if anyone was wondering, I make hand drums to play Plena (music from Puerto Rico) and I built a 24inx24inx26in printer to be able to print the drums in one go using the duet. That's why I have so many 15 to 20 hour prints to do.

@gloomyandy said in Scanning Z probe G31: invalid Z probe index:

@charliedrums said in Scanning Z probe G31: invalid Z probe index:

uet SZP firmware version 3.5.0-rc.1+ (2023-11-20 12:50:20)

Your SZP does not seem to be running 3.5.0-rc.3. Probably best to make sure all of the boards are using the same version.

Totally brain farted, this was the issue. I was trying to update the SZP board trough putty with sudo apt update but it kept saying everything was updated. Fetched the rc3 update bin file for the SZP from the github directory and uploaded it trough DWC and installed it from there. That seemed to be my problem. I don't get the G31: invalid Z probe index at start up anymore. Thanks everyone for the help.

This just happened to me on a 14 hour print. I updated to RRF3.4. Came here to see what it could be. I resumed the print and is printing fine now. the print is still going as I write.

=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.0rc2 (2022-02-22 17:04:17) running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956BA-NA3TN-6JTD0-3SJ6S-1V82V
Used output buffers: 10 of 40 (40 max)
=== RTOS ===
Static ram: 150984
Dynamic ram: 66520 of which 28 recycled
Never used RAM 129804, free system stack 114 words
Tasks: SBC(resourceWait:,0.7%,494) HEAT(notifyWait,0.0%,321) Move(notifyWait,1.7%,248) CanReceiv(notifyWait,0.0%,772) CanSender(notifyWait,0.0%,346) CanClock(delaying,0.0%,339) TMC(notifyWait,8.4%,58) MAIN(running,89.1%,923) IDLE(ready,0.0%,30), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 15:54:21 ago, cause: power up
Last software reset at 2022-03-09 01:00, reason: HardFault, GCodes spinning, available RAM 130308, slot 1
Software reset code 0x4063 HFSR 0x80000000 CFSR 0x00000000 ICSR 0x00400803 BFAR 0x00000000 SP 0x2041b4f8 Task MAIN Freestk 1672 ok
Stack: 20429f28 2042c2d8 2041b594 00000001 0000002e 0045c81b 0045c676 61070000 20419a7c 2042bf34 00000000 00000001 00000000 004844d7 2042bf34 00000000 00000000 0048481f 003ffff0 004849f7 20429860 ffffffff 0934d918 2042bf34 20419a7c 2042c2dc ffffffff
Error status: 0x04
Aux0 errors 0,0,0
Step timer max interval 135
MCU temperature: min 47.3, current 47.5, max 47.7
Supply voltage: min 23.9, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
Heap OK, handles allocated/used 99/1, heap memory allocated/used/recyclable 2048/160/126, gc cycles 0
Events: 2 queued, 2 completed
Driver 0: pos 60689, ok, SG min 0, mspos 928, reads 41145, writes 0 timeouts 0
Driver 1: pos 14056, ok, SG min 0, mspos 616, reads 41145, writes 0 timeouts 0
Driver 2: pos 50096, standstill, SG min 0, mspos 72, reads 41145, writes 0 timeouts 0
Driver 3: pos 0, standstill, SG min 0, mspos 664, reads 41146, writes 0 timeouts 0
Driver 4: pos 0, standstill, SG min 0, mspos 152, reads 41146, writes 0 timeouts 0
Driver 5: pos 0, standstill, SG min 0, mspos 104, reads 41145, writes 0 timeouts 0
Date/time: 2022-03-09 16:28:53
Slowest loop: 31.03ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 20, maxWait 796ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 678710, completed 678677, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state 3
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.3
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP* is doing "M122" in state(s) 0 0, running macro
Telnet is idle in state(s) 0
File* is doing "G1 X453.419006 Y257.640015 E-0.570000" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause* is idle in state(s) 0
Code queue is empty
=== Filament sensors ===
Extruder 0: no data received
=== CAN ===
Messages queued 15065, received 12407, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 268, free buffers 50 (min 47), ts 3026/3026/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
Transfer state: 4, failed transfers: 0, checksum errors: 0
RX/TX seq numbers: 15043/15043
SPI underruns 0, overruns 0
State: 5, disconnects: 0, timeouts: 0, IAP RAM available 0x2b8b0
Buffer RX/TX: 1520/2544-0, open files: 0
=== Duet Control Server ===
Duet Control Server v3.4-rc2
File /opt/dsf/sd/gcodes/Pandero11in_Escalas_0.6n_0.3mm_PLA_13h57m.gcode is selected, processing
HTTP:
Executing macro 0:/macros/Diagnostics, started by M98 P"0:/macros/Diagnostics"
> Next stack level
File:
Buffered code: G1 X453.419 Y257.64 E-.57
Buffered code: G1 E-.03 F2400
Buffered code: G1 Z63.02 F720
Buffered code: G1 X457.643 Y264.663 F10800
Buffered code: G1 Z62.62 F720
Buffered code: G1 E.6 F2400
Buffered code: G1 F4200
Buffered code: G1 X458.599 Y265.619 E.09391
Buffered code: G1 F8640
Buffered code: G1 X457.643 Y264.663 E-.35695
Buffered code: G1 E-.24305 F2400
Buffered code: G1 Z63.02 F720
Buffered code: G1 X459.911 Y269.805 F10800
Buffered code: G1 Z62.62 F720
Buffered code: G1 E.6 F2400
Buffered code: G1 F4200
Buffered code: G1 X460.905 Y270.799 E.09959
Buffered code: G1 F8640
Buffered code: G1 X459.911 Y269.805 E-.37085
Buffered code: G1 E-.22915 F2400
Buffered code: G1 Z63.02 F720
Buffered code: G1 X463.158 Y276.331 F10800
Buffered code: G1 Z62.62 F720
Buffered code: G1 E.6 F2400
==> 992 bytes
Code buffer space: 1552
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
Full transfers per second: 39.36, max time between full transfers: 44.0ms, max pin wait times: 29.1ms/8.3ms
Codes per second: 18.47
Maximum length of RX/TX data transfers: 3928/1628

Finished downgrading the 6hc and 1lc to 3.3. Going to start a 17 hour print and see how it goes will report back with findings

@phaedrux Brought it up to 70. Going to do some test prints to see if I get the error again.

M591 D0
Duet3D rotating magnet filament monitor v3 on pin 121.io1.in, enabled, sensitivity 24.84mm/rev, allow 35% to 130%, check printing moves every 15.0mm, version 3, mag 132 agc 70, measured sensitivity 24.82mm/rev, min 98% max 101% over 556.6mm

@droftarts
It was not grounded but it is now. Since it takes a couple of days to get here I went and ordered a 1LC v1.3 board to see if that changes anything.

I updated the bootloader on the 1LC and I have grounded the bracket and now the screws and the hemera are grounded. This time I started a print and it started over extruding right from the start. Maybe now with the updated bootloader and grounded everything, updaye everything to 3.5.2 and see what happens? I'll keep trying stuff until the new 1LC gets here. I'll keep the thread updated to my findings.