I have been using simplify3d on past versions of DuetWifi, now with version 2 I cannot select the tool. I have my tool set up as T0 in Duet but when I select T0 or T1 for the extruder it doesn't select the tool and throws an error. Anyone have any idea how to select the tool?
@arnold_r_clark This did it. Works as expected now! Thanks all - on to the next problem 
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
@phaedrux said in BLTouch3 + Duet2 + RRPF3 Upgrade (not working properly):
M280
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2.2 running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S8-6J9D6-3SJ6S-1A4GJ
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73244 of which 200 recycled
Never used RAM 15176, free system stack 184 words
Tasks: NETWORK(ready,186) HEAT(blocked,308) MAIN(running,449) IDLE(ready,20)
Owned mutexes:
=== Platform ===
Last reset 00:03:02 ago, cause: software
Last software reset at 2022-01-01 10:06, reason: User, GCodes spinning, available RAM 15352, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 20.8, current 25.0, max 25.2
Supply voltage: min 24.1, current 24.3, max 24.7, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2022-01-01 10:09:34
Cache data hit count 221935625
Slowest loop: 6.06ms; fastest: 0.21ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.89ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(1) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.26
WiFi MAC address 48:3f:da:a6:ef:04
WiFi Vcc 3.38, reset reason Power up
WiFi flash size 2097152, free heap 23624
WiFi IP address 192.168.1.16
WiFi signal strength -52dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 2 0 0 0 0 0
M98 P"config.g"
M98 P"config.g"
Heater 0 is disabled because its model is undefined
Heater 1 is disabled because its model is undefined
I just haven't run the tuning yet
@DIY-O-Sphere
I added that line to the the config. New config here -
; Communication and general
M111 S0 ; Debug off
M550 P"BigBot" ; Machine name (P + anything you like)
M551 P"reprap" ; Machine password (used for FTP connections)
M552 S1 ; Enable WiFi
M555 P2 ; Set output to look like Marlin
M575 P1 B57600 S1 ; Comms parameters for PanelDue
M669 k1 ; set CoreXY mode
; Configuration
M569 P0 S0 ; X Drive 0 goes forwards (change to S0 to reverse it)
M569 P1 S1 ; Y Drive 1 goes forwards.
M569 P2 S1 ; ZaZb - Motors - Forwards
M569 P3 S1 ; E0 Drive 3 goes forwards 0
M569 P4 S1 ; E1 Drive 4 goes forwards
M350 X16 Y16 Z16 E16 I1 ; Set 16x microstepping with interpolation
M92 X100 Y100 Z397 ; Set axis steps/mm.
M92 E415 ; Set extruder steps/mm.
M906 X800 Y800 Z800 E800 ; Set motor currents (mA).
M201 X1000 Y1000 Z500 E500 ; Accelerations (mm/s^2)
M203 X12000 Y12000 Z1200 E800 ; Maximum speeds (mm/min)
M566 X800 Y800 Z30 E600 ; Maximum jerk speeds mm/minute
M208 X300 Y300 Z500 ; set axis maxima (adjust to suit your machine)
M208 X0 Y0 Z0 S1 ; set axis minima (adjust to make X=0 and Y=0 the edges of the bed)
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
; Endstops
M574 X1 S1 P"xstop"
M574 Y2 S1 P"!^ystop"
; Z probe BLTouch
M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F200 T2000
G31 X39 Y50 Z1 P2.5
M557 X15:285 Y15:285 S25
; Heaters & Temp Sensors
M308 S0 P"bedtemp" Y"thermistor" T100000 B4388 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4388 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 ; disable bang-bang mode for heater and set PWM limit
; Tools
M563 P0 D0 H1 F0 ; define tool 0
; Fans
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
;*** If you are using axis compensation, put the figures in the following command
M556 S78 X0 Y0 Z0 ; Axis compensation here
M208 S1 Z0 ; set minimum Z
M501 ; Load Config-Override.g that is created using M500
T0 ; select first hot end
; M98 P/sys/homeall.g
On power up it is still cycling the test and turning solid red. Just nothing with the M280 commands. I am going to go through the PDF and see if I missed anything.
I have found lots of posts on this and cannot seem to get my BL up and running after upgrading to the new board/firmware.
I have to be missing something here with the new syntax - it was all just working before the upgrade. I do have to do a wire continuity test but hopefully it is just an issue with the new config.
Here is my config:
; Communication and general
M111 S0 ; Debug off
M550 PBigBot ; Machine name (P + anything you like)
M551 Preprap ; Machine password (used for FTP connections)
M552 S1 ; Enable WiFi
M555 P2 ; Set output to look like Marlin
M575 P1 B57600 S1 ; Comms parameters for PanelDue
M669 k1 ; set CoreXY mode
; Configuration
M569 P0 S0 ; X Drive 0 goes forwards (change to S0 to reverse it)
M569 P1 S1 ; Y Drive 1 goes forwards.
M569 P2 S1 ; ZaZb - Motors - Forwards
M569 P3 S1 ; E0 Drive 3 goes forwards 0
M569 P4 S1 ; E1 Drive 4 goes forwards
M350 X16 Y16 Z16 E16 I1 ; Set 16x microstepping with interpolation
M92 X100 Y100 Z397 ; Set axis steps/mm.
M92 E415 ; Set extruder steps/mm.
M906 X800 Y800 Z800 E800 ; Set motor currents (mA).
M201 X1000 Y1000 Z500 E500 ; Accelerations (mm/s^2)
M203 X12000 Y12000 Z1200 E800 ; Maximum speeds (mm/min)
M566 X800 Y800 Z30 E600 ; Maximum jerk speeds mm/minute
M208 X300 Y300 Z500 ; set axis maxima (adjust to suit your machine)
M208 X0 Y0 Z0 S1 ; set axis minima (adjust to make X=0 and Y=0 the edges of the bed)
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
; Endstops
M574 X1 S1 P"xstop"
M574 Y2 S1 P"!^ystop"
; Z probe BLTouch
M558 P9 C"^zprobe.in"H5 F200 T2000
G31 X39 Y50 Z1 P2.5
M557 X15:285 Y15:285 S25
; Heaters & Temp Sensors
M308 S0 P"bedtemp" Y"thermistor" T100000 B4388 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4388 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 ; disable bang-bang mode for heater and set PWM limit
; Tools
M563 P0 D0 H1 F0 ; define tool 0
; Fans
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
;*** If you are using axis compensation, put the figures in the following command
M556 S78 X0 Y0 Z0 ; Axis compensation here
M208 S1 Z0 ; set minimum Z
M501 ; Load Config-Override.g that is created using M500
T0 ; select first hot end
; M98 P/sys/homeall.g
Home Z (trying to get homez.g working and then I will update homeall.g)
G91 ; relative positioning
G1 H2 Z5 F4800 ; lift Z relative to current position
G90 ; absolute positioning
G1 X150 Y105 F4800 ; go to first probe point
G30 ; home Z by probing the bed```
deployprobe.g:
M280 P0 S10
retract.g:
M280 P0 S90
@dc42 Hey all - finally got time to pull it apart. I replaced the wires with a lower gauge wire and everything works perfectly again. Thanks for the quick responses.
The issue:
I printed fine last night - I have been running with no problems for the great half of the year. I uploaded a new print this morning to kick off and it gave me a driver error reporting on drivers 0 1 2 3 4 - so I rebooted it hoping it was just a glitch - no. The screen and all led lights are flickering.
First was to check the power supply and that is still staying consistent at 24v - and my lighting LEDs are on. Not sure what the issue could be - couple restarts, reseated power - no luck. See pics please.
As of right now I am dead in the water.
That was it. Ended up not having X set up properly. Now I just have bltouch problems 
Thanks
@dc42 Great. I purchased it from filastruder. Order #35977. What would I have to do to start the process?
Would something like this be covered under the warranty?