@deckingman Thanks for the help. it works fine now.

@Veti i see, Thanks a lot.

@Veti what do u mean by r parameter? sorry i dont really understand programming language.

@Veti Thanks, so its gonna be

M305 P1 T100000 B4725 C7.060000e-8 ; set thermistor + ADC parameters for heater 1

?

@deckingman Thanks alot. will give it a try now.

@Veti i see, Im actually wondering about it too. but since i dont know much about it. i just leave it as is and do a temperature tower later on.

Im using the stock Bed thermistor for CR-10S and E3D V6 Tube Thermistor for my hotend. i dont know what their names are so idk what to set my thermistor as. if you know, mind sharing it? thanks.

@deckingman Thanks. It makes a lot of sense now.
My Slicer start Gcode is only
G28 ; home all axes
G1 Z5 F5000 ; lift nozzle

should i add T0 as u said? if yes can u give me an example of the completed code?

M584 X0 Y1 Z2:3 E4 ; set drive mapping
M350 X16 Y16 Z16:16 E16 I1 ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z400.00:400.00 E415.00 ; set steps per mm
M566 X900.00 Y900.00 Z24.00:24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z2000.00:2000.00 E6000.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00:100.00: E10000.00 ; set accelerations (mm/s^2)
M906 X750 Y750 Z750:750 E650 I30 ; set motor currents (mA) and motor idle factor in per cent

as to why i have 2 Z settings. if i dont do it like this. my extruder wont even move.

Print Temp is the same as to when i calibrate Esteps. so i dont think is not hot enough.

; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S0 ; physical drive 4 goes backwards
M584 X0 Y1 Z2:3 E4 ; set drive mapping
M350 X16 Y16 Z16:16 E16 I1 ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z400.00:400.00 E415.00 ; set steps per mm
M566 X900.00 Y900.00 Z24.00:24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z2000.00:2000.00 E6000.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00:100.00: E10000.00 ; set accelerations (mm/s^2)
M906 X750 Y750 Z750:750 E650 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z400 S0 ; set axis maxima

; Endstops
M574 X1 Y1 S1 ; set active high endstops

; Z-Probe
M574 Z1 S2 ; set endstops controlled by probe
M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
M558 P9 H5 F420 T6000 A3 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X32 Y-2 Z5.19 ; set Z probe trigger value, offset and trigger height
M557 X32:300 Y10:300 S134 ; define mesh grid

; Heaters
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss