Posts made by massimilianoconti

hello as soon as I have the data I attach them. I wanted to know what compiler you need to open the source code to change the firmware... from the asset I downloaded in zip the purge code but you need a compiler ...

I know thanks does not respond well the command compared to before now they are both activated simultaneously. there is something wrong. if I go from the dual panel it works for example but we will see thanks. I did not quite understand if the developer of the firmware is only Mr. Dozuki or beyond people.

I'm not an expert I'm just an electrical engineer but personally I face a project with this logic keeping the fundamental hinges 100% additional things instead in the background such as not to create malfunctions to the rest

you have the silicone socks I'm reviewing everything as soon as I perform a new test I attach it

I try thanks

ok of nothing

serious problem when activating the extruder to load or download filament, in dweb controll do not activate the speed keys and millimeters see figure. I repeat it is useless to add a thousand news if then the heart of the firmware is not good and always lacks something fundamental. doing so does not appear serious and reliable. I would make a software working 100% for its fundamental features then comes the rest, being careful not to unbalance everything.

duet 3 v1.01

firmware 3.4 RC1

my hot end is Phaetus dragonfly bmsBMSÕ«×Õ+⵿íÕ×ï.stl BMS Wireframes (7).pdf

10/2/2022, 13:29:16 Warning: heater behaviour was not consistent during tuning
Auto tuning heater 1 completed after 3 idle and 50 tuning cycles in 2520 seconds. This heater needs the following M307 command:
M307 H1 R2.558 K0.275:0.103 D6.31 E1.35 S1.00 B0 V23.9
Send M500 to save this command in config-override.g
10/2/2022, 13:05:33 Warning: heater behaviour was not consistent during tuning
Auto tune starting phase 4, measuring with fan on

when I start tuning takes too long something in the algorithm must be changed. if I put 3 as hysteresis comes to completion for example. something needs to be changed in the tuning procedure. my hotend is geometrically excellent, it is designed to perform every temperature and material

the wiring is fine the mechanics and thermal side are fine is an unresolved problem of the firmware, this defect was previously not there. I had pointed out copme other users the problem already in version 3.4 beta 7 the only thing maybe is the different sensor the pt1000 of e3d.

m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.0rc1 (2022-02-09 10:28:13) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-9P63L-DJMSS-6J9DD-3S46N-TVFH8
Used output buffers: 1 of 40 (22 max)
=== RTOS ===
Static ram: 150984
Dynamic ram: 95712 of which 164 recycled
Never used RAM 103548, free system stack 142 words
Tasks: NETWORK(ready,26.4%,229) ETHERNET(notifyWait,0.1%,168) HEAT(notifyWait,0.0%,238) Move(notifyWait,0.0%,262) CanReceiv(notifyWait,0.0%,944) CanSender(notifyWait,0.0%,356) CanClock(delaying,0.0%,333) TMC(notifyWait,8.1%,58) MAIN(running,65.3%,925) IDLE(ready,0.0%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:14:15 ago, cause: power up
Last software reset at 2022-02-07 21:11, reason: User, GCodes spinning, available RAM 100532, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 131
MCU temperature: min 24.6, current 39.4, max 39.5
Supply voltage: min 16.2, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: pos 192000, standstill, SG min 0, mspos 583, reads 54286, writes 23 timeouts 0
Driver 1: pos 0, standstill, SG min 0, mspos 617, reads 54286, writes 23 timeouts 0
Driver 2: pos 33603, standstill, SG min 0, mspos 649, reads 54286, writes 23 timeouts 0
Driver 3: pos 0, standstill, SG min 0, mspos 1, reads 54295, writes 14 timeouts 0
Driver 4: pos 0, standstill, SG min 0, mspos 1, reads 54296, writes 14 timeouts 0
Driver 5: pos 0, standstill, SG min 0, mspos 8, reads 54299, writes 11 timeouts 0
Date/time: 2022-02-10 12:52:42
Slowest loop: 5.17ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 5.6ms, write time 0.9ms, max retries 0
=== Move ===
DMs created 125, segments created 11, maxWait 377072ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 29, completed 29, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 1], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 7701, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 50 (min 50), ts 4280/0/0
Tx timeouts 0,0,4279,0,0,3420 last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 18.71ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• Ethernet -
  State: active
  Error counts: 0 0 0 0 0
  Socket states: 5 2 2 2 2 0 0 0
  10/2/2022, 12:51:58 Auto tune starting phase 3, measuring
  10/2/2022, 12:49:54 Auto tune starting phase 2, settling
  10/2/2022, 12:47:20 Auto tune starting phase 1, heating up
  10/2/2022, 12:47:15 M98 P"0:/macros/Tuning T0"

m115
FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC FIRMWARE_VERSION: 3.4.0rc1 ELECTRONICS: Duet 3 MB6HC v1.01 or later FIRMWARE_DATE: 2022-02-09 10:28:13

; Configuration file for Duet 3 (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Fri Dec 31 2021 12:22:58 GMT+0100 (Ora standard dell’Europa centrale)

; General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Duet 300X Dual" ; set printer name
M955 P0 C"spi.cs3+spi.cs2"
M669 K1 ; select CoreXY mode

; Network
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S1 ; physical drive 0.1 goes forwards
M569 P0.2 S0 ; physical drive 0.2 goes forwards
M569 P0.3 S0 ; physical drive 0.3 goes forwards
M569 P0.4 S0 ; physical drive 0.4 goes forwards
M584 X0.0 Y0.1 Z0.2 E0.3:0.4 ; set drive mapping
M350 X128 Y128 Z128 E128:128 I1 ; configure microstepping with interpolation
M92 X640.00 Y640.00 Z5171.72 E3367.10:3367.70 ; set steps per mm
M566 X800.00 Y800.00 Z60.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z500.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
M201 X2000.00 Y2000.00 Z20.00 E250.00:250.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800:800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
M593 P"zvd" F70

; Axis Limits
M208 X-18 Y-5 Z0 S1 ; set axis minima
M208 X305 Y305 Z260 S0 ; set axis maxima

M671 X10:295:295:10 Y280:280:5:5 P0.5
M591 D0 P5 C"e0_stop" R40:120 E3.0 S0

; Endstops
M574 X1 S1 P"io1.in" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin io1.in
M574 Y1 S1 P"io2.in" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin io2.in
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"io7.out" ; create servo pin 0 for BLTouch
M558 P9 C"^io7.in" H5 F500:100 T6000 A5 R0.1 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X12.5 Y-20 Z1.493 ; set Z probe trigger value, offset and trigger height
M557 X15:295 Y15:300 S25:20 ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin temp0
M950 H0 Q10 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S130 ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"pt1000" ; configure sensor 1 as PT1000 on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S400 ; set temperature limit for heater 1 to 400C
M308 S2 P"temp2" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 2 as thermistor on pin temp2
M950 H2 C"out2" T2 ; create nozzle heater output on out2 and map it to sensor 2
M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H2 S280 ; set temperature limit for heater 2 to 280C

; Fans
M950 F0 C"out4" Q500 ; create fan 0 on pin out4 and set its frequency
M106 P0 S0 H1:2 T45 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"out5" Q500 ; create fan 1 on pin out5 and set its frequency
M106 P1 S0 H-1 ; set fan 1 value. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F1 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
M563 P1 D1 H2 F1 ; define tool 0
G10 P1 X25 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool
M150 X0 ; set LED type to NeoPixel and set SPI frequency to 3MHz
M150 B255 P128 S65 F0
M501

duet 3 v1.01

firmware 3.4 rc1

M303 T1 S270 Y3

the problem of the heater is not solved, something must be changed in the firmware must be made more stable and reliable. it is not convenient to continuously add new features but make a stable and precise firmware then slowly add other news. otherwise you will never get to a fully functional software

then your code was put first at the beginning then at the second attempt at the end of the macro. the home I ran after the printing had started so the machine was busy. thanks for the help

no is the latest version. I just rerun the tool and says Configuration Tool v3.3.10 on Thu Jan 27 2022 19:23:58

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Sat Jan 01 2022 15:36:30 GMT+0100 (Ora standard dell’Europa centrale)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-310 Y-310 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-310 ; home X axis
G1 H1 Y-310 ; home Y axis
G1 X5 Y5 F6000 ; go back a few mm
G1 H1 X-310 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-310 ; then move slowly to Y axis endstop
G90 ; absolute positioning
G1 X15 Y35 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed
; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90

original version

the firmware must be corrected

adding the code in home all if sending home during printing is executed anyway.

I try thanks

System:

Duet 3 v1.01

firmware 3.4 beta7+7

I noticed an incorrect operation that would be eliminated that is: when the printer is being printed and even by mistake the home of the axes is done, the home operation is performed going to compromise the print and risking to damage the print. the home operation absolutely should not be performed when the machine is printing!!!!!

S= number of bed screws